Biofilm formation and electricity generation of a microbial fuel cell started up under different external resistances
Liang Zhang,Xun Zhu,Jun Li,Qiang Liao,Dingding Ye
DOI: https://doi.org/10.1016/j.jpowsour.2011.04.013
IF: 9.2
2011-01-01
Journal of Power Sources
Abstract:To investigate the effects of external resistance on the biofilm formation and electricity generation of microbial fuel cells (MFCs), active biomass, the content of extracellular polymeric substances (EPS) and the morphology and structure of the biofilms developed at 10, 50, 250 and 1000 Ω are characterized. It is demonstrated that the structure of biofilm plays a crucial role in the maximum power density and sustainable current generation of MFCs. The results show that the maximum power density of the MFCs increases from 0.93 ± 0.02 W m −2 to 2.61 ± 0.18 W m −2 when the external resistance decreases from 1000 to 50 Ω. However, on further decreasing the external resistance to 10 Ω, the maximum power density decreased to 1.25 ± 0.01 W m −2 because of a less active biomass and higher EPS content in the biofilm. Additionally, the 10 Ω MFC shows a highest maximum sustainable current of 8.49 ± 0.19 A m −2 . This result can be attributed to the existence of void spaces beneficial for proton and buffer transport within the anode biofilm, which maintains a suitable microenvironment for electrochemically active microorganisms. Keywords External resistance Microbial fuel cell Power density Sustainable current generation Biofilm structure 1 Introduction Microbial fuel cell (MFC) is an economical pathway to a sustainable energy future. In a typical MFC, electron donors, such as organic materials in waster, are oxidized by the electrochemically active bacteria mostly growing as a biofilm on the anode surface [1,2] . Although experiencing a significant development in recently years, the power generation is still insufficient for the practical applications. In order to improve the MFC performance, efforts have been made to enrich more electrochemically active bacteria [3–5] , to improve reactor configuration [6–10] , to identify better electrode materials [6,8–12] , as well as to optimize process parameters [6,13] . Optimizing the growth conditions for the electrochemically active bacteria in the anode was also an important consideration for improving the performance of MFCs. Many factors, such as nutrient supply, flow rate, pH, temperature [2,6,7,14,15] , have been found to strongly affect the MFC performance and start-up time. One of the most important and most investigated factors is the anode potential at which the MFC is operated, as it controls the theoretical energy gain for microorganisms [16] . Finkelstein et al. [17] reported that a larger and earlier maximum current were obtained at a more positive applied potential due to the increased energy yield for microbial colonization. In addition, Aelterman et al. [4] found that the anode potential had no influence on the start-up time but an improved current and power generation can be obtained at an optimal anode potential of −200 mV vs. Ag/AgCl. Wang et al. [18] reported that a poised potential of 200 mV (vs. Ag/AgCl) accelerated the start-up of MFCs. Recently, Wei et al. [19] investigated the current and biomass production of G. sulfurreducens growing on anodes at a potential of −160, 0, and 400 mV (vs. SHE). The results indicated that faster start-up times, higher current generation and greater biomass production were achieved when the anode set to 0 and 400 mV. Besides the anode potential, the effect of external resistance applied to the electrical circuit also received wild attention since controlling the growth condition for the electrochemically active bacteria by changing the external resistance is more feasible than poising the anode potential in MFC applications. Generally speaking, MFC performance increases with decreasing the applied external resistance. Liu et al. [20] demonstrated that the lower external resistance was applied, the higher maximum power output was obtained. Aelterman et al. [12] reported a significant increase both in continuous current generation and in power generation when the external resistance of MFCs was lowered from 50 to 25 and then to 10.5 Ω when the MFC was operated at each resistance for 9–11 days. In addition, the changes in the microbial diversity and metabolism were also noted when different external resistances were applied to the MFCs. Lyon et al. [21] observed large differences in power generation and structure of microbial community when MFCs were operated at different external resistances. Rismani-Yazdi et al. [22] investigated the effect of external resistance on bacterial diversity and metabolism in MFCs. They found that changes in the external resistance affected not only the power generation, but also the microbial metabolism. Mclean et al. [23] described how difference in external resistances affect cellular electron transfer rates on a per cell basis and overall biofilm development in Shewanella oneidensis strain MR-1 by monitoring the real-time microscopic imaging of anode population. They found that the anode of a MFC started up at a low resistance (100 Ω) has a thinner biofilm and higher current per cell, compared with that at a high external resistance (1 MΩ). Moreover, the power production and coulombic efficiency of MFCs can be substantially improved using an automatic control strategy of external resistance as reported by Premier et al. [24] . The external resistance may also influence the MFC performance by affecting the structure of the biofilm in the anode. For an MFC using organic matters as substrate, a lower external resistance usually leads to a higher amount of electrons per unit of time from the biofilm to electrode, and therefore a higher proton production rate in the interior of the biofilm. As a result, when the MFC is operated under a low external resistance, the higher proton production rate will cause a pH drop within the biofilm, which in turn would lead to unfavorable microenvironments for the growth of the electrochemically active bacteria. On the other hand, it is well known that the architecture of the biofilm adapts in response to environmental stresses, such as low nutrient availability, high shear forces, unfavorable pH value and toxic compounds. Therefore, it was reasonable to postulate that the morphology and structure of the biofilm developed at various external resistances would be different dues to the different proton producing rates within the biofilm. In the present study, four biofilm samples were established in the anode of a two-chamber MFC using acetate as substrate employing anaerobic mixed consortia as anodic inoculums under an external resistance of 10, 50, 250 and 1000 Ω. The objectives of the present study were to assess the effects of external resistance on the start-up process, biofilm formation and structure, as well as the electricity generation of the MFCs. 2 Materials and methods 2.1 MFC configuration and operation The experiments were conducted using four two compartment MFCs. Each MFC consisted of a proton exchange membrane (PEM) (Nafion 117, Dupont), two carbon cloth electrodes (E-TEK, B-1A, America) and two plexiglass plates with a flow channel holding a volume of 2.7 mL. The PEM and electrodes had an apparent surface area of 25 cm 2 . The anode compartment was inoculated with the effluent from a MFC running on acetate. Both anode and cathode compartments were equipped with Ag/AgCl reference electrodes. All MFC tests were conducted in a temperature-controlled room at 25 °C and were repeated three times to check reproducibility of the data. In order to evaluate the impact of external resistances, the MFCs were started at an external resistance of 10, 50, 250, and 1000 Ω (denoted as MFC-10, MFC-50, MFC-250 and MFC-1000, respectively). After 7 days of operation, fresh anolyte, containing sodium acetate 2.7 g L −1 , 6 g L −1 Na 2 HPO 4 , 3 g L −1 KH 2 PO 4 , 0.1 g L −1 NH 4 Cl, 0.5 g L −1 NaCl, 0.1 g L −1 MgSO 4 ·7H 2 O, 15 mg L −1 CaCl 2 ·2H 2 O and 1.0 mL L −1 of a trace elements solution, was fed at a rate of 1.5 L day −1 . To minimize the influence of the cathode potential on the overall cell performance, a 50 mM potassium ferricyanide solution was continuously supplied to the cathode at a rate of 1 mL min −1 during the start-up stage and steady-state operation. 2.2 Data acquisition and analysis Cell voltages ( U ), currents ( I ), anode and cathode potentials of each MFC were collected every 15 s via an Agilent 34970A data acquisition unit connected to a PC. In the measurement, the external resistance was varied in a range of (5–1.0) × 10 5 Ω to control the condition of discharging and record the voltage–current curves. After each change in the electrical resistance, the MFCs were held until the current and cell voltage reached steady-state. The power density of the MFCs was calculated according to Eq. (1) : (1) P = U × I A where A is the surface area of the electrode, I and U are the sustainable current and cell voltage after the MFC reached steady-state, respectively. The cyclic voltammetry (CV) experiments were carried out in a range from −0.6 to +0.37 V vs. SHE at a scan rate of 5 mV s −1 using a Zennium electrochemical workstation (Zahner, Germany) with the anode as the working electrode. The cathode was used as the counter electrode and the reference electrode was an Ag/AgCl reference electrode. The metabolic energy gain (MEG) for the electrochemically active bacteria was calculated with the following equation described by Wei et al. [19] : (2) M E G = ∫ 0 t ( E andoe ( t ) − E 0 ′ ) I ( t ) d t where E anode ( t ) and I ( t ) are the anode potential and current at time t during start-up period respectively. E 0 ′ is the standard potential of CO 2 /acetate (−0.29 V). The unavailable part of MEG for the electrochemically active bacteria was neglected because this portion make up less than 20% of the MEG when the MFC was started up by applying an external resistance to the electrical circuit [19] . 2.3 SEM characterization The morphology of biofilms formed under different external resistances was analyzed by a scanning electron microscopy (SEM) (3400N, HITACHI instrument). At the removal from the anode compartment, the samples was immediately sliced by a sterilized bistoury, and fixed by phosphate buffer saline (PBS) with 2.5% glutaraldehyde (pH 7.2–7.4) for 1 h. The samples were then washed three times with the same buffer and dehydrated stepwise with a graded series of ethanol solutions (30, 50, 70, 80, 90 and 100%). The electrode samples were finally critical-point dried with tert-butyl ethanol and sputter coated with a thin layer of gold. The biofilm was observed in high vacuum using SEM in the secondary electron imaging mode. 2.4 Quantization of biofilm components 2.4.1 Biomass quantification by phospholipid method For the evaluation of total active biomass, small pieces of anode electrode with biofilms were taken from the MFCs and analyzed according to the procedure reported by Verstraete [4] as soon as the current generation was stable. The phosphate concentration released from phospholipids was determined using a Leng Guang 756mc spectrophotometer at 610 nm. Phosphate concentration was then correlated to total active biomass using the conversion factor of 191.7 μg of biomass-C per 100 mmol of phospholipid [25] . 2.4.2 EPS characterization The characteristics of biofilm EPS (extracellular polymeric substances) in each reactor were analyzed according to Fang et al. [26] . Four biofilm-coated samples were removed from each MFC after the start-up and immersed in 50 mL of a pH 7.5 TE buffer containing 10 mM Trizma base, 10 mM EDTA and 2.5% NaCl. Biofilm was scrapped from each sample, and centrifuged at 3500 rpm for 20 min. The concentrated biomass was then re-suspended in 10 ml of a 0.85% sodium chloride solution containing 0.22% formaldehyde at 80 °C for 30 min for EPS extraction. The EPS dissolved in the formaldehyde solution was recovered by further centrifugation at 3500 rpm for 30 min. The carbohydrate content of EPS (EPS c ) in the extracted solution was measured using the phenol/sulfuric-acid method [27] and the protein content (EPS p ) using the Lowry method [28] . The sum of EPS p and EPS c represented the total EPS of the samples. Lactose and bovine serum albumin were used to make calibration curves for the determination of carbohydrates and proteins EPS, respectively. 3 Results and discussion 3.1 Influence of external resistance on the start-up process During the start-up period, the anode compartment was inoculated with the effluent from a MFC running on acetate in a continuous feed mode. As shown in Fig. 1 a , both current generation, anode and cathode potential of the MFCs were significantly affected by the external resistance. The lag period for MFC-10 was 2.2 day, reaching 14.6 mA after 6.3 days ( Fig. 1 ). Correspondingly, the potential of the anode and the cathode evolved from their initial potentials to −0.14 V and +0.41 V (vs. SHE), respectively. For MFC-50, a steady state current of about 11.2 mA and anode potential of −0.19 V (vs. SHE) were obtained after a 4.3-day start-up period. Fig. 1 also shows a steady current of 2.8 and 0.7 mA, a steady anode potential of −0.23 and −0.25 V (vs. SHE) and a start-up time of 3.0 and 2.6 days for MFC-250 and MFC-1000, respectively. From these results, it is clear that the MFC with a lower resistance showed a higher steady anode potential and current generation after start-up. During start-up, the power of MFC-10, MFC-50, MFC-250 and MFC-1000 increased from 0 to 1.96, 6.05, 1.95 and 0.64 mW, respectively. Fig. 1 also illustrates that there was no obvious change in current generation and anode potential for the four MFCs after the replacement of fresh anolyte, suggesting successful biofilm establishment on the surface of carbon cloth in the anode chamber. 3.2 Influence on active biomass and energy gain for microorganisms The influence of external resistance on the accumulated active biomass and the energy gain of the biofilms formed at 10, 50, 250 and 1000 Ω during the period of start-up is presented in Fig. 2 a . It can be seen that the energy gain for the electrochemically active bacteria decreased with the increase of external resistance from 10 to 1000 Ω. Such a result was expected because a lower external resistance induced a higher current generation and a higher potential difference between the anode potential and the redox potential of acetate, both leading to a higher energy gain for the microorganisms (Eq. (2) ). It is also interesting to note that the energy gain for the electrochemically active bacteria grown at 10 Ω (1112.4 J) was significantly higher than the previously reported range of 0–180 J [19] . This result can be mainly attributed to the higher current densities (6.0 A m −2 ) obtained in this study compared with the previous study (0–2.0 A m −2 ). From Fig. 2 a, it also can be seen that the active biomass of the MFCs increased with the decrease of external resistance from 1000 to 50 Ω, and then decreased with external resistance from 50 to 10 Ω. This trend is inconsistent with previous reports in which a higher biomass production was observed at a lower external resistance because of the increased energy gain for the microorganisms at low resistances [3,12] . This probably related to the fact that a higher portion of energy was consumed for the synthesis of EPS rather than for bacterial growth in the case of MFC-10, as will be shown in the following paragraph. It is commonly accepted that the energy for microorganism is essential for the maintenance of the bacterial vitality [29] . However, the microorganisms may also produce EPS during growth on the anode surface, consuming energy which is available for bacterial growth [30] . EPS could contribute up to 50–90% of the total organic carbon of biofilms and serves many functions such as promoting the initial attachment of cells to solid surfaces, maturing biofilm structure, and enhancing biofilm resistance to environmental stress and disinfectants. The existence of EPS on the anode surface of bio-electrochemical systems fed with various substrates has been noted in recent studies [31–33] . In this study, the EPS content of the anode biofilms developed at various external resistances after start-up was also estimated and elucidated in Fig. 2 b. It appears that the EPS content of biofilm increased as the external resistance increased. For instance, the EPS content of biofilm established during start-up decreased from 296.8 ± 42.9 to 51.9 ± 4.2 mg g carbon-cloth − 1 when the external resistance was increased from 10 to 1000 Ω. Considering that the active biomass of the biofilm developed at 10 Ω was lower than that of 50 Ω, whereas the energy gain was higher, this result suggested that a greater portion of energy was consumed for EPS synthesis in the case of the biofilm developed at 10 Ω. 3.3 Influence on electrochemical behavior of biofilms In order to evaluate the importance of mediators produced by the microorganisms for electricity generation, CV tests were conducted on the anode during stable current generation and with depleted substrate. From the voltammograms in Fig. 3 , all the biofilms during stable current generation ( Fig. 3 a) show catalytic behavior for the bioelectrooxidation of acetate by the appearance of an oxidation current at an onset potential of −0.26 V (vs. SHE) during the anodic scan. In the cathodic scan, additional oxidation peaks can be observed around −0.16 V (vs. SHE) and no reduction peaks were found. It is obvious from Fig. 3 a that the voltammograms of all the samples exhibited no significant difference, except that the oxidation peak (0.11 V vs. SHE) of the biofilms established at 50 Ω was significantly higher than that obtained from the other samples. This improvement can be attributed to the higher active biomass within the biofilm of MFC-50, as indicated in Fig. 2 a. In comparison, all the curves for the anodes with depleted substrate ( Fig. 3 b) exhibited oxidation peaks at −0.1 V (vs. SHE) and reduction peaks at −0.18 V (vs. SHE). These results are consistent with previous studies [20,34] , which were indicative of the existence of mediators produced by the mixed culture. The similarities among these results also suggest that the dominant species in the biofilms were slightly influenced by changes in the external resistance from 10 to 1000 Ω [35] . In addition, considering that the current responses of the anodes during stable current generation were much stronger than that of the redox peaks with depleted substrate, it is reasonable to postulate that direct electron transfer was the main mechanism for current generation by the biofilms. 3.4 Influence on biofilm formation Fig. 4 displays SEM microphotographs of the surface of the anode biofilms grown under different external resistances. Although the morphology of the biofilm may have been altered by the dehydration process, the SEM results provided good comparative information demonstrating clear differences in the architectures of the biofilm established at various external resistances. It can be clearly seen from Fig. 3 a–d that the biofilms did not totally cover the electrode surface except for the biofilm developed at 10 Ω. For MFC-10, the entire anode surface was covered by the biofilm, converting the porous, rough electrode surface to a smooth, uniform one. The SEM images at higher magnification ( Fig. 4 e–h) provide further insight into the morphology of the biofilms formed at different external resistances. Compared with Fig. 4 f–h, Fig. 3 e indicates that the biofilm established at 10 Ω contained greater amounts of EPS than that of the biofilm developed at 50, 250 and 1000 Ω. This observation corroborates the EPS results seen in Fig. 2 b. The cross sectional morphology of the biofilm samples was also obtained in this study by SEM ( Fig. 5 ). SEM images show that the biofilms were only developed on the surface of the electrode and only few bacteria grew into the porous carbon cloth matrix. This could be attributed to both the small pore size and the limited substrate supply within the carbon cloth matrix. Similar phenomenon was also observed when reticulated vitreous carbon was used as anode support [31] . In addition, as can be seen in Fig. 5 , all the biofilms exhibited substantial heterogeneity in thickness. The average thicknesses of the biofilms formed under 10 ( Fig. 5 a) and 50 Ω ( Fig. 5 b) was significantly higher than that at 250 ( Fig. 5 c) and 1000 Ω ( Fig. 5 d). This result can be mainly attributed to the higher active biomass and EPS content in the biofilm samples established at 10 and 50 Ω. It is also interesting to note that although the biofilm formed at 10 Ω contained less active biomass than that at 50 Ω, both biofilms were of similar thickness. Putting these results together and recalling that the biofilm formed at 10 Ω contained more EPS than that at 50 Ω, one could assumed that the bacteria was more loosely packed in the biofilm developed at 10 Ω. In order to further confirm this point, the microstructures of the biofilms formed at different external resistances were observed in higher magnification ( Fig. 5 e–h). It can be clearly seen from these figures that the extensive voids were found to be distributed within biofilm established at 10 Ω. These voids were beneficial for mass transport within the biofilm by forming water channels that facilitate the substrate and buffer supply, as well as product removal. It should be pointed out, however, that the existence of void spaces within the biofilms would also lead to imperfect contact between the electroactive microorganisms and the anodes, causing a decrease in the electrical conductivity of the biofilm matrixes and consequently the lowered performance of the MFCs. By contrast, the biofilm formed at 50, 250 and 1000 Ω ( Fig. 5 f–h) appeared quite homogeneous throughout its thickness and few voids can be discerned. Based on the results from the surface and cross-sectional SEM images, it is apparent that the biofilms developed at 50, 250 and 1000 Ω showed a compact structure, in which cells are tightly linked together by visible polymeric viscous materials. 3.5 Influence on electricity generation Fig. 6 compared the polarization curves of the MFCs (10 kΩ to 5 Ω) started up at different external resistances. The details of the MFC performance were summarized in Table 1 . As illustrated in Fig. 6 and Table 1 , the maximum power density of the MFCs decreased in the following order: MFC-50 > MFC-250 > MFC-10 > MFC-1000. The best performance of MFC-50 may come from the highest active biomass production ( Fig. 2 a) on the surface of the carbon paper. The lower performance of MFC-10, despite the higher active biomass, might be due to the significant ohmic loss ( Table 1 ) resulting from the existence of void spaces in the interior of the biofilm. More importantly, it is clear from Fig. 6 b that there were steep falls of cell voltage at relatively high current densities in the case of MFC-50, MFC-250 and MFC-1000, whereas a gradually decrease in the cell voltage with the increase of current density can be noted for MFC-10. The experiments were repeated three times with similar results. The rapid fall of cell voltage at high current densities is a common phenomenon for both single [36–38] and stacked MFCs [39] . In order to further study this phenomenon, the variation of the voltage of the MFCs with step-change of external resistance during performance evaluation were recorded and shown in Fig. 7 . As can be seen in Fig. 7 , a slow decrease of voltage with time followed by a steep fall of voltage output was observed when an external resistance of 150, 50 and 20 Ω was connected to the electrical circuit of MFC-1000, MFC-250 and MFC-50, respectively. Whereas in the case of MFC-10, a stable voltage was reached within 20 min even when the external resistance as low as 5 Ω was applied. As a consequence, MFC-10 exhibits a highest maximum sustainable current density ( I max ) of 8.49 ± 0.19 A m −2 ( Table 1 ), while MFC-50, MFC-250 and MFC-1000 reached a limit of 5.78 ± 0.39, 2.46 ± 0.02 and 1.25 ± 0.01 A m −2 , respectively. The observed differences can be explained by the improved buffer access and proton removal in the case of the biofilm developed at 10 Ω. It is well known that the electrochemical oxidation of acetate is an acid-producing process. In the anode compartment, acetate is oxidized according to the following reaction: C H 3 COO − + 2 H 2 O → 2 C O 2 + 7 H + + 8 e − As shown in the above equation, the oxidation of every mole of acetate produces 7 mol of proton, which can result in a pH decrease within the biofilm microenvironment. This can lead to an increase in the potential for acetate oxidation and an inhabitation of microbial metabolism, both negatively influencing the MFC performance [40] . When a MFC was operated at a high current density or a low resistance, this problem becomes more serious due to the higher proton production rate. For MFC-50, MFC-250 and MFC-1000, the compact structure of the biofilms ( Fig. 5 f–h) hindered the buffer access and proton removal, leading to gradual accumulation of proton in the interior of the biofilm. When the proton concentration within the biofilm exceeded a critical value, the current generation of the MFCs became unsustainable over time due to the inhibition of the electrochemically active bacteria. Correspondingly, steep drops in cell voltage were observed ( Fig. 7 a–c). By contract, the biofilm formed at 10 Ω has a looser structure ( Fig. 5 e) with void spaces within the biofilm. These characteristics facilitated water and buffer access as well as proton removal. As a result, the highest sustainable current can be obtained by MFC-10 due to the maintenance of the favorable microenvironment for the microorganisms within the anode biofilm. 4 Conclusions In the present study, the effects of external resistance on the biofilm formation and electricity generation were investigated. Structural and morphological characterizations of the biofilms formed at various external resistances indicate that a suitable biofilm structure is crucial for the maximum power density and sustainable current generation of the MFCs. The experimental results showed that the biofilm established at a higher external resistance tended to form a compact structure with a less active biomass and a lower EPS content. This led to an increase of the maximum power density with the decrease of external resistance. However, when the external resistance became lower than the optimum value, a loose biofilm structure with a less active biomass and a higher EPS content was developed, resulting in more void spaces beneficial for proton and buffer transport and reduction of the electrical conductivity within the biofilm. Therefore, a lower maximum power density and higher maximum sustainable current generation can be obtained. Acknowledgements This work was supported by the National Natural and Science Foundation of China (Nos. 50806087 and 50825602 ), and Fundamental Research Funds for the Central Universities (No. CDJXS11142230 ). The authors also wish to thank Ms. Lu at the Central laboratory of Third Military Medical University for assistance in SEM measurements. References [1] B.E. Logan B. Hamelers R. Rozendal U. Schröder J. Keller S. Freguia P. Aelterman W. Verstraete K. Rabaey Environ. Sci. Technol. 40 2006 5181 5192 [2] K. Rabaey W. Verstraete Trends Biotechnol. 23 2005 291 298 [3] S. Freguia K. Rabaey Z. Yuan J. Keller Environ. Sci. Technol. 41 2007 2915 2921 [4] P. Aelterman S. Freguia J. Keller W. Verstraete K. Rabaey Appl. Microbiol. Biotechnol. 78 2008 409 418 [5] X. Cao X. Huang N. Boon P. Liang M. Fan Electrochem. Commun. 10 2008 1392 1395 [6] H. Liu R. Ramnarayanan B.E. Logan Environ. Sci. Technol. 38 2004 2281 2285 [7] S. You Q. Zhao J. Zhang J. Jiang C. Wan M. Du S. Zhao J. Power Sources 173 2007 172 177 [8] Q. Deng X. Li J. Zuo A. Ling B.E. Logan J. Power Sources 195 2010 1130 1135 [9] Y. Feng Q. Yang X. Wang B.E. Logan J. Power Sources 175 2010 1841 1844 [10] H. Liu S. Cheng L. Huang B.E. Logan J. Power Sources 179 2008 274 279 [11] U. Schröder J. Nießen F. Scholz Angew. Chem. Int. Ed. 115 2003 2986 2989 [12] P. Aelterman M. Versichele M. Marzorati N. Boon W. Verstraete Bioresour. Technol. 99 2008 8895 8902 [13] G.C. Gil I.S. Chang B.H. Kim M. Kim J.K. Jang H.S. Park H.J. Kim Biosens. Bioelectron. 18 2003 327 334 [14] G.S. Jadhav M.M. Ghangrekar Bioresour. Technol. 100 2009 717 723 [15] T. Catal P. Kavanagh V. O’Flaherty D. Leech J. Power Sources 196 2011 2676 2681 [16] R.C. Wagner D.F. Call B.E. Logan Environ. Sci. Technol. 44 2010 6036 6041 [17] D.A. Finkelstein L.M. Tender J.G. Zeikus Environ. Sci. Technol. 40 2006 6990 6995 [18] X. Wang Y. Feng N. Ren H. Wang H. Lee N. Li Q. Zhao Electrochim. Acta 54 2009 1109 1114 [19] J. Wei P. Liang X. Cao X. Huang Environ. Sci. Technol. 44 2010 3187 3191 [20] H. Liu S. Cheng B.E. Logan Environ. Sci. Technol. 39 2005 658 662 [21] D.Y. Lyon F. Buret T.M. Vogel J.M. Monier Bioelectrochemistry 78 2010 2 7 [22] H.R. Rismani-Yazdi A.D. Christy S.M. Carver Z. Yu B.A. Dehority O.H. Tuovinen Bioresour. Technol. 102 2011 278 283 [23] J.S. Mclean G. Wanger Y.A. Gorby M. Wainstein J. Mcquaid S.I. Ishii O. Bretschger H. Beyenal K.H. Nealson Environ. Sci. Technol. 44 2010 2721 2727 [24] G.C. Premier J.R. Kim I. Michie R.M. Dinsdale A.J. Guwy J. Power Sources 196 2011 2013 2019 [25] R.H. Findlay G.M. King L. Watling Appl. Environ. Microbiol. 55 1989 2888 2893 [26] H.H.P. Fang L.C. Xu K.Y. Chan Water Res. 36 2002 4709 4716 [27] A.F. Gaudy Ind. Water Wastes 7 1962 17 22 [28] O.H. Lowry N.J. Rosebrough A.L. Farr R.J. Randall J. Biol. Chem. 193 1951 265 275 [29] U. Schröder Phys. Chem. Chem. Phys. 9 2007 2619 2629 [30] N. Qureshi B.A. Annous T.C. Ezeji P. Karcher I.S. Maddox Cell. Fact 4 2005 24 44 [31] C.I. Torrres R. Krajmalnik-brown P. Parameswaran A. Kato Marcus G. Wanger Y.A. Gorrby B.E. Rittmann Environ. Sci. Technol. 43 2009 9519 9524 [32] H. Yi K.P. Nevin B.C. Kim A.E. Franks A. Klimes L.M. Tender D.R. Lovely Biosens. Bioelectron. 24 2009 3498 3503 [33] A. Larrosa-Guerrero K. Scott K.P. Katuri C. Godinez I.M. Head T. Curtis Appl. Microbiol. Biotechnol. 87 2010 1669 1713 [34] J.R. Kim S.H. Jung J.M. Regan B.E. Logan Bioresour. Technol. 98 2007 2568 2577 [35] S.A. Patil F. Harnisch B. Kapadnis U. Schröder Biosens. Bioelectron. 26 2010 803 808 [36] B. Min Ó.B. Román I. Angelidaki Biotechnol. Lett. 30 2008 1213 1218 [37] D.P.B.T.B. Strik H. Terlouw H.V.M. Hamelers C.J.N. Buisman Appl. Microbiol. Biotechnol. 81 2008 659 668 [38] A. Heijne H.V.M. Hamelers M. Saakes C.J.N. Buisman Electrochim. Acta 53 2008 5697 5703 [39] P. Aelterman K. Rabaey H.T. Pham N. Boon W. Verstraete Environ. Sci. Technol. 40 2006 3388 3394 [40] C.I. Torres A.K. Marcus B.E. Rittmann Biotechnol. Bioeng. 100 2008 872 881
What problem does this paper attempt to address?
-
Performance of a Batch Two‐chambered Microbial Fuel Cell Operated at Different Anode Potentials
Xin Wang,Yujie Feng,Jia Liu,He Lee,Nanqi Ren
DOI: https://doi.org/10.1002/jctb.2558
2011-01-01
Abstract:BACKGROUND: For a microbial fuel cell (MFC), the anode potential is an important electrochemical parameter for the growth, electron distribution and electrical activity of exoelectrogenic bacteria.RESULTS: The performance of a batch-flow two-chambered MFC was investigated operated at anode potentials of -400, -200, 0, +200 and +400 mV versus Ag/AgCl reference electrode. Glucose was used as substrate and ferricyanide as cathodic electron acceptor. At potentials from -400 to +200 mV, increasing maximum current outputs were obtained, ranging from 6.0 to 8.6 mA. However, the maximum current output decreased to 6.9 mA when the anode potential was further increased to +400 mV. More positive potentials resulted in higher Coulombic efficiencies (CEs), with values increased from 64% (-400 mV) to 88% (+400 mV). Electrons deposited as H(2) and CH(4) resulted in lower CEs at more negative potentials (-400, -200 and 0 mV). When +400 mV was applied to the anode, the growth yield dropped from 0.25 +/- 0.05 to 0.11 mol biomass mol(-1) COD (chemical oxygen demand) with inhibition of electrical activity.CONCLUSIONS: The most positive anode potential reduced growth yield and inhibited bacterial growth, but electrical activity increased for potentials ranged from -400 to +200 mV. When the potential was increased to +400 mV, growth yield was limited, affecting MFC performance. (C) 2011 Society of Chemical Industry
-
External circuit loading mode regulates anode biofilm electrochemistry and pollutants removal in microbial fuel cells
Han Xu,Xiao-Li Yang,Zhi-Hao Zhang,Yang-Guang Xia,Hai-Liang Song
DOI: https://doi.org/10.1016/j.biortech.2024.131300
Abstract:This study investigated the effects of different external circuit loading mode on pollutants removal and power generation in microbial fuel cells (MFC). The results indicated that MFC exhibited distinct characteristics of higher maximum power density (Pmax) (named MFC-HP) and lower Pmax (named MFC-LP). And the capacitive properties of bioanodes may affect anodic electrochemistry. Reducing external load to align with the internal resistance increased Pmax of MFC-LP by 54.47 %, without no obvious effect on MFC-HP. However, intermittent external resistance loading (IER) mitigated the biotoxic effects of sulfamethoxazole (SMX) (a persistent organic pollutant) on chemical oxygen demand (COD) and NH4+-N removal and maintained high Pmax (424.33 mW/m2) in MFC-HP. Meanwhile, IER mode enriched electrochemically active bacteria (EAB) and environmental adaptive bacteria Advenella, which may reduce antibiotic resistance genes (ARGs) accumulation. This study suggested that the external circuit control can be effective means to regulate electrochemical characteristics and pollutants removal performance of MFC.
-
Power generation in fed-batch microbial fuel cells as a function of ionic strength, temperature, and reactor configuration.
Hong Liu,Shaoan Cheng,Bruce E Logan
DOI: https://doi.org/10.1021/es050316c
IF: 11.4
2005-01-01
Environmental Science & Technology
Abstract:Power density, electrode potential, coulombic efficiency, and energy recovery in single-chamber microbial fuel cells (MFCs) were examined as a function of solution ionic strength, electrode spacing and composition, and temperature. Increasing the solution ionic strength from 100 to 400 mM by adding NaCl increased power output from 720 to 1330 mW/m(2). Power generation was also increased from 720 to 1210 mW/m(2) by decreasing the distance between the anode and cathode from 4 to 2 cm. The power increases due to ionic strength and electrode spacing resulted from a decrease in the internal resistance. Power output was also increased by 68% by replacing the cathode (purchased from a manufacturer) with our own carbon cloth cathode containing the same Pt loading. The performance of conventional anaerobic treatment processes, such as anaerobic digestion, are adversely affected by temperatures below 30 degrees C. However, decreasing the temperature from 32 to 20 degrees C reduced power output by only 9%, primarily as a result of the reduction of the cathode -potential. Coulombic efficiencies and overall energy recovery varied as a function of operating conditions, but were a maximum of 61.4 and 15.1% (operating conditions of 32 degrees C, carbon paper cathode, and the solution amended with 300 mM NO). These results, which demonstrate that power densities can be increased to over 1 W/m(2) by changing the operating conditions or electrode spacing, should lead to further improvements in power generation and energy recovery in single-chamber, air-cathode MFCs.
-
Anode biomass rather than soluble organic matter is fuel for electricity production in microbial fuel cell at longer hydraulic retention time
Fumichika Tanaka,Li Xie,Yosuke Ishii,Shinji Kawasaki,Naoko Yoshida
DOI: https://doi.org/10.1016/j.jclepro.2023.140544
IF: 11.1
2024-01-27
Journal of Cleaner Production
Abstract:This study presents a novel method for independently calculating organic matter (OM) removal and electricity generation in a microbial fuel cell (MFC) treating sewage. This methodology used OM concentration as the exclusive variable for input, facilitating the prediction of electricity generation with variable Coulombic efficiency. The employed MFC, of tubular design, incorporates an air core surrounded by a carbon-based cathode, an anion exchange membrane , nonwoven graphite fabric, and encircled by twelve carbon brush anodes. This setup successfully reduced chemical oxygen demand (COD) from 180 to 50 mg L −1 and biological oxygen demand (BOD) from 84 to 15 mg L −1 within a 35 h hydraulic retention time (HRT). The resulting effluent BOD satisfies Japanese wastewater treatment standards. In the early HRT phase, the MFC exhibited rapid OM reduction, followed by a stabilization of OM concentration. Despite varying HRTs and the sustained OM levels at prolonged HRTs, the MFC consistently generated 0.29 ± 0.14 A m −2 . This apparent contradiction prompted the consideration of additional OM sources from the anode biomass ( C b ). Calculating electricity production based on OM concentration rather than OM degradation was achieved by assessing anode resistance ( R A n ) across different levels of OM supplementation, employing the Butler–Volmer equation. This approach, incorporating considerations for C b and R A n , accurately reproduced MFC performance. It was observed that OM supplementation from C b constituted 50% at 11 h HRT and escalated to 90% at 27 h HRT. Further analysis, including 16S rRNA gene-based microbial community profiling, indicated that higher cathode resistance ( R Cat ) at 1.0 Ω m 2 , compared to a minimum R A n of 0.10 Ω m 2 , favored methanogenesis over electrogenesis on the carbon brushes. This finding underscores the importance of reducing R Cat and minimizing electrode distance, coupled with enhancing the specific surface area of both electrodes, as crucial factors for the advancement of MFC technology.
environmental sciences,green & sustainable science & technology,engineering, environmental
-
Intermittent Contact of Fluidized Anode Particles Containing Exoelectrogenic Biofilms for Continuous Power Generation in Microbial Fuel Cells
Jia Liu,Fang Zhang,Weihua He,Xiaoyuan Zhang,Yujie Feng,Bruce E. Logan
DOI: https://doi.org/10.1016/j.jpowsour.2014.03.071
IF: 9.2
2014-01-01
Journal of Power Sources
Abstract:Current generation in a microbial fuel cell can be limited by the amount of anode surface area available for biofilm formation, and slow substrate degradation kinetics. Increasing the anode surface area can increase the amount of biofilm, but performance will improve only if the anode material is located near the cathode to minimize solution internal resistance. Here we demonstrate that biofilms do not have to be in constant contact with the anode to produce current in an MFC. Granular activated carbon particles enriched with exoelectrogenic biofilm are fluidized (by stirring) in the anode chamber of the MFC, resulting in only intermittent contact between the particles and the anode current collector. The maximum power density generated is 951 +/- 10 mW m(-2), compared to 813 +/- 2 mW m(-2) for the control; without stirring (packed bed), and 525 +/- 1 mW m(-2) in the absence of GAC particles and without stirring. GAC-biofilm particles demonstrate capacitor-like behavior, but achieve nearly constant discharge conditions due to the large number of particles that contact the current collector. These results provide proof of concept for the development of flowable electrode reactors, where anode biofilms can be electrically charged in a separate storage tank and then rapidly discharged in compact anode chambers. (C) 2014 Elsevier B.V. All rights reserved.
-
Bacterial Competition for the Anode Colonization under Different External Resistances in Microbial Fuel Cells
Alexiane Godain,Naoufel Haddour,Pascal Fongarland,Timothy M. Vogel
DOI: https://doi.org/10.3390/catal12020176
IF: 3.9
2022-01-29
Catalysts
Abstract:This study investigated the effect of external resistance (Rext) on the dynamic evolution of microbial communities in anodic biofilms of single-chamber microbial fuel cells fueled with acetate and inoculated with municipal wastewater. Anodic biofilms developed under different Rext (0, 330 and 1000 ohms, and open circuit condition) were characterized as a function of time during two weeks of growth using 16S rRNA gene sequencing, cyclic voltammetry (CV) and fluorescence microscopy. The results showed a drastic difference in power output of MFCs operated with an open circuit and those operated with Rext from 0 to 1000 ohms. Two steps during the bacterial community development of the anodic biofilms were identified. During the first four days, nonspecific electroactive bacteria (non-specific EAB), dominated by Pseudomonas, Acinetobacter, and Comamonas, grew fast whatever the value of Rext. During the second step, specific EAB, dominated by Geobacter and Desulfuromonas, took over and increased over time, except in open circuit MFCs. The relative abundance of specific EAB decreased with increasing Rext. In addition, the richness and diversity of the microbial community in the anodic biofilms decreased with decreasing Rext. These results help one to understand the bacterial competition during biofilm formation and suggest that an inhibition of the attachment of non-specific electroactive bacteria to the anode surface during the first step of biofilm formation should improve electricity production.
chemistry, physical
-
Micro Computed Tomography As Powerful Tool for Analyzing Post Mortem Biofilm and Carbonate on Operated Cathode in Single Chamber Microbial Fuel Cell
Maurizio Santini,Manfredo Guilizzoni,Massimo Lorenzi,Plamen Atanassov,Enrico Marsili,Stephanie Fest-Santini,Pierangela Cristiani,Carlo Santoro
DOI: https://doi.org/10.1149/ma2016-01/36/1848
2016-04-01
ECS Meeting Abstracts
Abstract:The cathode performances are one of the main limitations related with microbial fuel cell (MFC) that strongly limit the overall output. The low power produced is an important problem that has to be addressed for the scale up of the MFCs. Cathodic overpotential is particularly high at circumneutral pH when carbonaceous or metallic catalysts are used [1]. Overpotentials are much lower for enzymes but enzymatic biocathodes are expensive and not durable [2]. Single chamber membrane-less MFCs are preferred due to the lower cost and higher power output. In membrane-less MFCs, both electrodes (anode and cathode) are exposed directly to the electrolyte or carbon-rich solution. The presence of growing bacteria inside the chamber generates electron acceptor-rich and electron donor-rich zones, which serve as cathode and anode, respectively. In fact, bacteria consume rapidly the oxygen inside the chamber creating anaerobic conditions that are useful for electrogenic bacteria for colonizing the anode electrode and oxidize organics. The cathode used is an air-breathing cathode and it is porous and allows oxygen to penetrate through the anodic solution. A biofilm is formed also on the cathode surface consuming the oxygen and forming a natural and cheap membrane that separate the cathode from the solution and stop the oxygen leaking inside the chamber, thus ensuring anaerobic conditions. Strict anaerobes grow quickly within 1 week of operations as recently showed [3]. It has been showed previously that the biofilm formation on the cathode initially increased the cathodic reduction reaction [4]. In this work, we analyzed the cathode performances and the MFC overall performance along 6 months operations [5]. At the end of the experimentation, the cathode has been examined with X-Ray Micro Computed Tomography (microCT), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX) for characterizing the organic/inorganic layer on the cathode surface facing the solution [5]. Single chamber MFC with volume of 125 mL was used and the cell was fed with raw wastewater and sodium acetate. The results obtained showed that cathode reduction reaction increased in the first 15 days but then decreased continuously over time [5]. The initial increase might be due to the formation of an initial biofilm layer that probably enhanced the cathodic reduction reaction. Over time, precipitation of compounds and fouling might take place. It has been speculated that thick biofouling decreased the performances. After 6 months, part of the cathode was dried and analyzed with SEM/EDX and the other part was analyzed as it is using microCT [5]. SEM has the great potential of very high resolution but images have to be taken after treating the sample and consequently change the morphology of the biofilm after drying it. Moreover, SEM is not able to pass through objects and consequently only the surface can be analyzed. The coupling with EDX allowed to identify sodium (Na) on the external part of the cathode and calcium (Ca) on the internal face [5]. Na and Ca were present in form of carbonate. The production of OH- due to the cathodic reaction, caused the alkalinization of solution at the interface with the cathode making the precipitation of carbonate species on the cathode is very probable. MicroCT images allowed making a complete 3D scan of the entire cathode analyzed. Interestingly, the different components (cathode, carbonate and biofilm) were clearly distinguishable (Figure 1). In fact, a compact and continuous thick layer of carbonate was clearly visible between the cathode and the biofilm (Figure 1, white color). Those results obtained using microCT clearly showed that the thick, not porous carbonate layer and not the biofilm itself might increase the proton mass transport resistance from the solution to the catalytic sites and lowering dramatically the cathode output during long terms operation. Reference [1] C. Santoro, F. Soavi, A. Serov, C. Arbizzani, P. Atanassov. Biosensors and Bioelectronics. 2016, 78, 229-235. [2] C. Santoro, S. Babanova, B. Erable, A. Schuler, P. Atanassov. Bioelectrochemistry. 2016, 108, 1-7. [3] M. Grattieri, S. Babanova, C. Santoro, E. Guerrini, S.P.M. Trasatti, P. Cristiani, M. Bestetti, P. Atanassov. Electroanalysis, 2015, 27(2), 327-335. [4] P. Cristiani, M.L. Carvalho, E. Guerrini, M. Daghio, C. Santoro, B. Li. Bioelectrochemistry, 2013, 92, 6-13. [5] M. Santini, M. Guilizzoni, M. Lorenzi, P. Atanassov, E. Marsili, S. Fest-Santini, P. Cristiani, C. Santoro. Biointerphases. 2015, 10, 031009. Figure 1. Cross Section of the cathode analyzed using microCT. Figure 1
-
Increased Power Generation in a Continuous Flow MFC with Advective Flow Through the Porous Anode and Reduced Electrode Spacing
S Cheng,H Liu,BE Logan
DOI: https://doi.org/10.1021/es051652w
IF: 11.4
2006-01-01
Environmental Science & Technology
Abstract:The maximum power generated in a single-chamber air-cathode microbial fuel cell (MFC) has previously been shown to increase when the spacing between the electrodes is decreased from 4 to 2 cm. However, the maximum power from a MFC with glucose (500 mg/L) decreased from 811 mW/ m(2) (R-ex = 200 Omega, Coulombic efficiency of CE = 28%) to 423 mW/m(2) (Rex = 500 Omega, CE = 18%) when the electrode spacing was decreased from 2 to 1 cm (batch mode operation, power normalized by cathode projected area). This decrease in power was unexpected as the internal resistance decreased from 35 Omega (2-cm spacing) to 16 Omega (1-cm spacing). However, providing advective flow through the porous anode toward the cathode substantially increased power, resulting in the highest maximum power densities yet achieved in an air-cathode system using glucose or domestic wastewater as substrates. For glucose, with a 1-cm electrode spacing and flow through the anode with continuous flow operation of the MFC, the maximum power increased to 1540 mW/m(2) (51 W/m(3)) and the CE increased to 60%. Using domestic wastewater (255 +/- 10 mg of COD/L), the maximum power density was 464 mW/m(2) (15.5 W/m(3); CE = 27%). Although flow through the anode could lead to plugging, especially for particulate substrates such as domestic wastewater, the system was operated using glucose for over 42 days without clogging. These results show that power output in this air-cathode single-chamber MFC can be increased by reducing the electrode spacing if the reactors are operated in continuous flow mode with advective flow through the anode toward the cathode.
-
Effects of Anode Materials on Electricity Generation and Organic Wastewater Treatment of 6 L Microbial Fuel Cells
Wei-jun DING,Li-liang YU,Jie CHEN,Shao-an CHENG
DOI: https://doi.org/10.13227/j.hjkx.201611106
2017-01-01
Abstract:Anode material is one of the most important tactors on the application of microbial fuel cells tor wastewater treatment due to its key role in forming exoelectrogenic biofilm and transferring electrons along with the high investment cost.In this study,carbon brush (CB),carbon cloth (CC) and graphite felt (GF) were investigated as alternative anode materials for 6 L single-chamber dual aircathode microbial fuel cells (MFCs) in terms of starting-up rate and electricity production with artificial wastewater and slaughter wastewater.The cost effectiveness of anode materials was also evaluated.The results showed that anode materials had no obvious effect on the start-up of MFC.All MFCs finished their started-up on day 24.Using artificial wastewater [acetate 1 g·L-1 in 50 mmol·L-1 phosphate buffer (PBS)] as substrate,the maximum power densities for the CB,CC and GF-MFCs were (56.3 ± 1.8) W·m-3,(46.0± 1.7) W·m-3,and (40.8 ± 1.5) W·m-3,while with slaughter wastewater MFCs could produce (19.5 ± 0.8) W· m-3,(16.9 ±0.6) W·m-3,and (11.9 ±0.5) W·m-3,respectively.COD removals of all the MFCs were approximately 90％ with both artificial wastewater and slaughter wastewater.The CB-MFCs had a cost of (3.44 ± 0.08) mW·yuan-with the artificial wastewaterand (0.97 ±0.05) mW·yuan-1 with slaughter wastewater,which were 18.6％,12.8％ higher than that of CC-MFCs and 38.7％,80％ higher than that of GF-MFCs,respectively.These results demonstrate that carbon brush is the most suitable material used in large-scale MFC.
-
Anodic Biofilm in Single-Chamber Microbial Fuel Cells Cultivated under Different Temperatures
Lihong Liu,Olga Tsyganova,Duu-Jong Lee,Ay Su,Jo-Shu Chang,Aijie Wang,Nanqi Ren
DOI: https://doi.org/10.1016/j.ijhydene.2012.03.084
IF: 7.2
2012-01-01
International Journal of Hydrogen Energy
Abstract:The microorganisms in anodic biofilms of a microbial fuel cell (MFC) oxidize substrates to generate electrons, protons, and metabolic products. This study started up two single-chamber MFCs at different temperatures (25 degrees C for MFC A and 15 degrees C for MFC B); after successful startup, the cell temperatures were swapped. The MFC A had peak voltage at 540 mV at 25 degrees C, which was decreased rapidly as fed substrate was consumed. At 15 degrees C, the MFC A yielded a nearly constant voltage of 500 mV over complete feed cycle. Conversely, the MFC B produced higher maximum power than MFC A, and can deliver nearly constant voltage over the entire feed cycle at either 15 or 25 degrees C. Electrochemical analysis revealed that the MFC B had lower internal resistance than MFC A, with the former having much lower anodic resistance than the latter. Microbial analysis showed that the MFC started up at low temperatures had anodic biofilm enriched with psychrophilic bacteria Simplicispira psychrophila LMG 5408(T)[AF078755] and Geobacter psychrophilus P35(T)[AY653549]. This study suggests the strategy to promote the development of anodic biofilms at low temperatures that are capable of yielding electricity at constant voltage. Copyright (c) 2012, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.
-
[Effect of the Initial Anode Potential on Electricity Generation in Microbial Fuel Cell].
Ming-Zhi Fan,Peng Liang,Xiao-Xin Cao,Xia Huang
DOI: https://doi.org/10.3321/j.issn:0250-3301.2008.01.044
2008-01-01
Abstract:The initial anode potential of the microbial fuel cell (MFC) was changed by additional circuit in the anode chamber, and the influence of the initial anode potential on the electricigens was studied. When the initial anode potential was 350 mV (vs Hg/Hg2 Cl2), the growth of microorganisms was much slower than that of the microorganisms which grew on the anode with an initial potential of -200 mV or 200 mV (vs Hg/Hg2 Cl2). After stable electricity generation, the anode resistances of the three MFCs, which had initial anode potentials of 350 mV, 200 mV and -200 mV respectively, were 71 Omega, 43 Omega and 80 Omega. The community structures in MFCs, before and after the electricity generation, were also studied by denaturing gradient gel electrophoresis (DGGE). Clostridium sticklandii, Pseudomonas mendocina and Paenibacillus taejonensis were the three most enriched strains on the anode.
-
[Electricity Generation Using the Short-Arm Air-Cathode Microbial Fuel Cell].
Kun Guo,Ding-jie Li,Hao-ran Li,Zhu-wei Du
DOI: https://doi.org/10.3321/j.issn:0250-3301.2009.10.045
2009-01-01
Environmental Sciences
Abstract:The short-arm air-cathode microbial fuel cell (ACMFC) was constructed using a cramp to fix the proton exchange membrane (PEM) and carbon paper with 0.5 mg/cm2 onto the short-arm side of the anode chamber. Exoelectrogens on the surface of graphite rod were enriched by a sludge microbial fuel cell from the anaerobic digestion sludge. And the cyclic voltammetry result showed these microbes had electrochemical activities. Using the graphite rod covered by exoelectrogens as the anode and sodium acetate as the substrate, the short-arm ACMFC showed a maximal power density (Pm) of 738 mW/m2, internal resistance (Ri) of 280 omega and open circuit voltage (OCV) of 741 mV. Continuous sparging the anode chamber with nitrogen or removal of the proton exchange membrane enhance the Pm of the cell to 745 mW/m2 and 759 mW/m2 respectively. When both of the two measures were used together, the Pm reached up to 922 mW/m2. Under these three conditions the Ri of the cell was kept around 280 omega. When the substrate concentration was 12.62-100.96 mg/L and external resistance was 510 omega, the maximal voltage of the cell and the substrate concentration showed an obvious linear relation (R2 = 0.99). But when the concentration was above 100.96 mg/L, the maximal voltage stably kept around 302mV(the external resistance was 510 omega). However, the Coulombic efficiency of the short-arm ACMFC gradually increased with the increase of the substrate concentration, from 31.83% to 45.03%.
-
Scale-up of Membrane-Free Single-Chamber Microbial Fuel Cells
Hong Liu,Shaoan Cheng,Liping Huang,Bruce E. Logan
DOI: https://doi.org/10.1016/j.jpowsour.2007.12.120
IF: 9.2
2008-01-01
Journal of Power Sources
Abstract:Scale-up of microbial fuel cells (MFCs) will require a better understanding of the effects of reactor architecture and operation mode on volumetric power densities. We compared the performance of a smaller MFC (SMFC, 28mL) with a larger MFC (LMFC, 520mL) in fed-batch mode. The SMFC produced 14Wm−3, consistent with previous reports for this reactor with an electrode spacing of 4cm. The LMFC produced 16Wm−3, resulting from the lower average electrode spacing (2.6cm) and the higher anode surface area per volume (150m2m−3 vs. 25m2m−3 for the SMFC). The effect of the larger anode surface area on power was shown to be relatively insignificant by adding graphite granules or using graphite fiber brushes in the LMFC anode chamber. Although the granules and graphite brushes increased the surface area by factors of 6 and 56, respectively, the maximum power density in the LMFC was only increased by 8% and 4%. In contrast, increasing the ionic strength of the LMFC from 100 to 300mM using NaCl increased the power density by 25% to 20Wm−3. When the LMFC was operated in continuous flow mode, a maximum power density of 22Wm−3 was generated at a hydraulic retention time of 11.3h. Although a thick biofilm was developed on the cathode surface in this reactor, the cathode potentials were not significantly affected at current densities <1.0mAcm−2. These results demonstrate that power output can be maintained during reactor scale-up; increasing the anode surface area and biofilm formation on the cathode do not greatly affect reactor performance, and that electrode spacing is a key design factor in maximizing power generation.
-
Tubular Membrane Cathodes for Scalable Power Generation in Microbial Fuel Cells.
Yi Zuo,Shaoan Cheng,Doug Call,Bruce E. Logan
DOI: https://doi.org/10.1021/es0627601
IF: 11.4
2007-01-01
Environmental Science & Technology
Abstract:One of the greatest challenges for using microbial fuel cells (MFCs) for wastewater treatment is creating a scalable architecture that provides large surface areas for oxygen reduction at the cathode and bacteria growth on the anode. We demonstrate here a scalable cathode concept by showing that a tubular ultrafiltration membrane with a conductive graphite coating and a nonprecious metal catalyst (CoTMPP) can be used to produce power in an MFC. Using a carbon paper anode (surface area Aan = 7 cm2, surface area per reactor volume Aan,s = 25 m2/m3), an MFC with two 3-cm tube cathodes (Acat = 27 cm2, Acat,s = 84 m2/m3) generated up to 8.8 W/m3 (403 mW/m2) using glucose [0.8 g/L in a 50 mM phosphate buffer solution (PBS)], which was only slightly less than that produced using a carbon paper cathode with a Pt catalyst (9.9 W/m3, 394 mW/m2; Acat= 7 cm2, Acat,s= 25 m2/m3). Coulombic efficiencies (CEs) with carbon paper anodes were 25-40% with tube cathodes (CoTMPP), compared to 7-19% with a carbon paper cathode. When a high-surface-area graphite brush anode was used (Aan = 2235 cm2, Aan,s = 7700 m2/m3) with two tube cathodes placed inside the reactor (Acat = 27 cm2, Acas, = 93 m2/m3), the MFC produced 17.7 W/m3 with a CE = 70-74% (200 mM PBS). Further increases in the surface area of the tube cathodes to 54 cm2 (120 m2/m3) increased the total power output (from 0.51 to 0.83 mW), but the increase in volume resulted in a constant volumetric power density (approximately 18 W/m3). These results demonstrate that an MFC design using tubular cathodes coated with nonprecious metal catalysts, and brush anodes, is a promising architecture that is intrinsically scalable for creating larger systems. Further increases in power output will be possible through the development of cathodes with lower internal resistances.
-
Set up of a Microbial Fuel Cell for the Treatment of a Garden Compost Leachate: Impact of the External Polarizing Electric Resistance Upon the Chemical Oxygen Demand Removal
Imene Laaz,Mostefa Kameche,Christophe Innocent
DOI: https://doi.org/10.14416/j.asep.2023.05.005
2023-05-24
Applied Science and Engineering Progress
Abstract:Microbial fuel cells (MFCs) are new and growing renewable energy devices. They transform chemical products into electricity with the help of microorganisms (enzymes, bacteria, microbes, etc.) acting as biocatalysts. They are nowadays displaying technological development since they concomitant simultaneously the wastewater treatment and the electric power generation. These two novelties incite researchers in the field, the utilization of this promising technology. As a matter of fact, a bioelectrochemical fuel cell has been elaborated and set up for garden compost leachate treatment. Following a previous study on the microbial anode formed from wastewater under the application of an electric potential either positive or negative by using chronoamperometry. In this work, we propose the simple method of connecting the two electrodes (anode and cathode) by electrical resistance, to flow a current. The impact of the polarizing electric load on the achievement of the MFC has therefore been studied. Moreover, the chemical oxygen demand (COD) removal for the MFC running for 7 days has been also investigated. It decreased and showed simultaneously an increase in the cell voltage. Thus, the effects of the external load on the current and power generation, as well as on pollutant removal, have been studied by modifying each time the external load. The external polarizing resistance (EPR) was increased from 1 to 10 kΩ, to assess the pollutant decay of the organic matter contained in the wastes. As a result of this, the voltage was increased, whilst the current was decreased, with increasing values of the EPR. The results have been discussed with respect to the type and the predominant microorganisms (electrogenic/fermentative) being involved during the generation of the electric current. This new technology is very promising for converting waste into electricity by offering a way to clean up the polluted environment.
-
External Resistances Applied to MFC Affect Core Microbiome and Swine Manure Treatment Efficiencies
Anna Vilajeliu-Pons,Lluis Bañeras,Sebastià Puig,Daniele Molognoni,Albert Vilà-Rovira,Elena Hernández-del Amo,Maria D. Balaguer,Jesús Colprim
DOI: https://doi.org/10.1371/journal.pone.0164044
IF: 3.7
2016-10-04
PLoS ONE
Abstract:Microbial fuel cells (MFCs) can be designed to combine water treatment with concomitant electricity production. Animal manure treatment has been poorly explored using MFCs, and its implementation at full-scale primarily relies on the bacterial distribution and activity within the treatment cell. This study reports the bacterial community changes at four positions within the anode of two almost identically operated MFCs fed swine manure. Changes in the microbiome structure are described according to the MFC fluid dynamics and the application of a maximum power point tracking system (MPPT) compared to a fixed resistance system (Ref-MFC). Both external resistance and cell hydrodynamics are thought to heavily influence MFC performance. The microbiome was characterised both quantitatively (qPCR) and qualitatively (454-pyrosequencing) by targeting bacterial 16S rRNA genes. The diversity of the microbial community in the MFC biofilm was reduced and differed from the influent swine manure. The adopted electric condition (MPPT vs fixed resistance) was more relevant than the fluid dynamics in shaping the MFC microbiome. MPPT control positively affected bacterial abundance and promoted the selection of putatively exoelectrogenic bacteria in the MFC core microbiome (Sedimentibacter sp. and gammaproteobacteria). These differences in the microbiome may be responsible for the two-fold increase in power production achieved by the MPPT-MFC compared to the Ref-MFC.
multidisciplinary sciences
-
Anode biofilm communities and the performance of microbial fuel cells with different reactor configurations
Qingqing Jiang,Defeng Xing,Rui Sun,Lu Zhang,Yujie Feng,Nanqi Ren
DOI: https://doi.org/10.1039/c6ra08790f
IF: 4.036
2016-01-01
RSC Advances
Abstract:The performance and anode biofilm formation of two types of microbial fuel cells (MFCs) were studied in this paper. During 175 days of operation of single-chamber microbial fuel cells (SMFCs), the voltage exceeded 300 mV over 74.9% of the running time and was over 500 mV for 49.3% of the time. For dual-chamber microbial fuel cells (DMFCs), the voltage exceeded 300 mV for 54.3% of the running time and was over 450 mV 50.9% of the time. The removal rate of COD reached 83.6% and 80.0% in the SMFCs and DMFCs, respectively. The maximum power outputs were 686 mW m(-2) and 776 mW m(-2) for the two types of MFCs during polarization. In this study, the 454 pyrosequencing technique, a massively parallel sequencing technology, was utilized to survey the microbial community of the anode biofilms in different MFC reactors. A variation existed between the biofilm communities of the two MFC anodes. This was presumably caused by different electron acceptors, which affected the extracellular electron transfer speed.
-
Study on Electricity Generation from Bio-cathode Microbial Fuel Cell
Deng-jie ZHONG,Xia HUANG,Peng LIANG,Xue XIA
DOI: https://doi.org/10.19853/j.zgjsps.1000-4602.2010.01.004
2010-01-01
Abstract:The effect of external resistance, initial substrate concentration and buffer solution on the electricity generation from a bio-cathode microbial fuel cell ( MFC) was studied. The results show that the MFC can operate stably when the external resistance is equal to or above 50Ω. The coulomb efficiency increases when the external resistance decreases. The MFC can operate longer when the initial substrate concentration is higher. The coulomb efficiency decreases while the initial substrate concentration increases. The buffer solution can improve output voltage and coulomb efficiency of the MFC. The solution pH value is kept neutral, which is optimal for microbial growth.
-
High Electric Production by Membraneless Microbial Fuel Cell with Up Flow Operation Using Acetate Wastewater
Aris Mukimin,Nur Zen,Hanny Vistanty,Purwanto Agus
DOI: https://doi.org/10.21771/jrtppi.2020.v11.no2.p19-27
2020-11-19
Jurnal Riset Teknologi Pencegahan Pencemaran Industri
Abstract:Microbial fuel cell (MFC) is a new proposed technology reported to generate renewable energy while simultaneously treating wastewater. Membraneless microbial fuel cell (ML-MFC) system was developed to eliminate the requirement of membrane which is expensive and prone to clogging while enhancing electricity generation and wastewater treatment efficiency. For this purpose, a reactor was designed in two chambers and connected via three pipes (1 cm in diameter) to enhance fluid diffusion. Influent flowrate was maintained by adjusting peristaltic pump at the base of anaerobic chamber. Carbon cloth (235 cm2) was used as anode and paired with gas diffusion layer (GDL) carbon-Pt as cathode. Anaerobic sludge was filtered and used as starter feed for the anaerobic chamber. The experiment was carried out by feeding synthetic wastewater to anaerobic chamber; while current response and potential were recorded. Performance of reactor was evaluated in terms of chemical oxygen demand (COD). Electroactive microbe was inoculated from anaerobic sludge and showed current response (0.55-0.65 mA) at 0,35 V, range of diameter 1.5-2 μm. The result of microscopics can showed three different species. The microbial performance was increased by adding ferric oxide 1 mM addition as acceptor electron. The reactor was able to generate current, voltage, and electricity power of 0.36 mA, 110 mV, and 40 mWatt (1.5 Watt/m2), respectively, while reaching COD removal and maximum coulomb efficiency (EC) of 16% and 10.18%, respectively.
-
Role of electrode and proton exchange membrane configurations on microbial fuel cell performance toward bioelectricity generation integrated wastewater treatment
Surajbhan Sevda,Vijay Kumar Garlapati,T R Sreekrishnan
DOI: https://doi.org/10.1080/10934529.2023.2168998
Abstract:In the present study, the effects of electrode surface area, proton exchange membrane area, and volume of the anodic chamber were investigated on the performance of five different dual chamber microbial fuel cells (MFC) using synthetic wastewater toward wastewater treatment coupled electricity generation. In the batch mode, the five different MFC's were operated with the anodic chamber volumes of 93-890 mL, 17.33-56.77 cm2 electrode surface area, obtained volumetric power densities of 137.72-58.13 mW/m3, and unit area power densities ranging from 27.04 to 11.94 mW/m2. Fed-batch studies were done with the MFC having 740 mL anodic chamber volume at different wastewater COD concentrations. The power density per unit area increased from 22.93 mW/m2 to 36.25 cm2 when the distance between electrodes was reduced from 10 to 6 cm. A maximum volumetric power density of 135.21 mW/m3 has been attained with a 6 cm electrode distance with the accomplished COD reduction of 93.21%. The presence of biofilm on the anode has been visualized through the SEM images. The higher COD concentration of wastewater and the fed-batch operation resulted in increased power output and wastewater treatment efficiency.