Abstract:Anion exchange membrane water electrolysis (AEMWE) is operated in an alkaline environment and has a similar membrane-electrode assembly (MEA) structure to that of proton exchange membrane water electrolysis (PEMWE). The use of non-noble metals as the electrocatalysts and operation at high current densities are inherently possible, so they are expected to be low-cost, high-performance candidates for next-generation water electrolysis systems. Improving the anion conductivity of the AEM and the activity of the non-precious metal catalysts is essential for the practical application of AEMWEs. 1 The non-noble electrocatalysts used in the MEA in this study were Ni 0.8 Co 0.2 O 2 and Ni 0.8 Fe 0.2 O, 3 which have a fused-aggregate network structure, and the electrolyte was a hydrocarbon-based AEM (QPAF-4) 4 , all of which were developed at the University of Yamanashi. The catalyst ink for the anodes was prepared by mixing the Ni 0.8 Co 0.2 O catalyst (University of Yamanashi) with solvent (water/methanol) and QPAF-4 (IEC = 2.0 meq g -1 , University of Yamanashi) binder solution. The anode ink was coated by using pulse-swirl-spray (PSS, Nordson) on the QPAF-4 membranes (IEC = 1.5 meq g -1 ) to make the catalyst-coated membranes (CCMs) with the anode. Catalyst inks for the cathodes was prepared by mixing Ni 0.8 Fe 0.2 O catalyst (University of Yamanashi) or Pt/CB catalyst (TEC10E50E, Tanaka Kikinzoku) with solvent (water/methanol) and QPAF-4 (IEC = 2.0 meq g -1 ) binder solution. The cathode ink was coated by using PSS on the gas diffusion layer (GDL, TGP-H-120, Toray) to make the gas diffusion electrodes (GDEs) for the cathodes. Ni mesh (Bekaert.co.jp) was used for the anode GDLs. The single cell (Figure 1, cell structure developed by Yokohama National University) performances were measured while supplying 1 M KOH at 80 °C to both electrodes. Figure 2 (a) shows the I-V performance of cells using Ni 0.8 Co 0.2 O for the anode and Ni 0.8 Fe 0.2 O or Pt/CB for the cathode. The electrolysis voltage observed for the cell with non-noble metal catalysts on both electrodes was higher than that for the cell with Pt/C on the cathode but was below 2 V at a current density of 1.2 A cm -2 . The value of the onset electrolysis voltage was nearly the same as that of the corresponding rotating disk electrode, 3 suggesting that the intrinsic performance of the cathode catalyst is being realized in the MEA. Increasing the amount of the cathodic catalyst loading scarcely affected the polarization. It is supposed that the fused-aggregate network structure of the Ni 0.8 Fe 0.2 O catalyst contributes to the favorable mass transfer. Figure 2 (b) shows the time dependence of the cell voltage of these cells. The increased loading amount improved the durability of the cathode. It is considered that the increase in the thickness of the cathode catalyst layer alleviated the damage of the GDL fibers to the membrane. These results indicate the possibility of adopting non-precious metal catalysts for both electrodes in AEMWE and thereby significantly reducing the catalyst cost. Acknowledgement This work was partially supported by NEDO of Japan through the AWE-1 project. References 1) A. Lim et al., J. Ind. Eng. Chem ., 76 , 410 (2019). 2) G. Shi et al., ACS Catal ., 12 , 14209 (2022). 3) G. Shi et al., ACS Omega , 8 , 13068 (2023). 4) H. Ono et al., J. Mater. Chem . A , 5 , 24804 (2017). Figure 1

Study on a Novel Manufacturing Process of Membrane Electrode Assemblies for Solid Polymer Electrolyte Water Electrolysis

Development of Cathode Ordered Membrane Electrode Assembly Based on TiO2 Nanowire Array and Ultrasonic Spraying

Influence and Improvement of Membrane Electrode Assembly Fabrication Methods for Proton Exchange Membrane Water Electrolysis

Comprehensive study and optimization of membrane electrode assembly structural composition in proton exchange membrane water electrolyzer

Highly Proton Conductive and Mechanically Robust SPEEK Composite Membranes Incorporated with Hierarchical Metal–organic Framework/carbon Nanotubes Compound

A Novel Approach to Fabricate Membrane Electrode Assembly by Directly Coating the Nafion Ionomer on Catalyst Layers for Proton-Exchange Membrane Fuel Cells

Optimization of catalyst-coated membranes for enhancing performance in proton exchange membrane electrolyzer cells

Ordered Membrane Electrode Assembly with Drastically Enhanced Proton and Mass Transport for Proton Exchange Membrane Water Electrolysis

(Invited) Progress and Perspective Towards Low-Cost High-Performance Anion Exchange Membrane Water Electrolysis

Investigation of membranes-electrodes assemblies in anion exchange membrane fuel cells (AEMFCs): Influence of ionomer ratio in catalyst layers

Performance and Durability of Membrane-Electrode Assemblies Using Non-Precious Metal Catalyst and a Hydrocarbon-Based Electrolyte for Anion Exchange Membrane Water Electrolysis

Development and application of ordered membrane electrode assemblies for water electrolysis

AEM Water Electrolysis with Ni-Based Catalysts and Tailored Poly(arylene piperidinium) Materials for Improved Stability

Ionomer Segregation in Composite MEAs and Its Effect on Polymer Electrolyte Fuel Cell Performance

Oriented intergrowth of the catalyst layer in membrane electrode assembly for alkaline water electrolysis

A novel preparation for a self-humidifying membrane electrode assembly and performance of its fuel cell

Optimizing proton exchange membrane fuel cell performance at low-humidity via constructing additional anodic water-retaining membrane layer containing sulfonated multi-walled carbon nanotubes

Hybrid 3D‐Ordered Membrane Electrode Assembly (MEA) with Highly Stable Structure, Enlarged Interface, and Ultralow Ir Loading by Doping Nano TiO 2 Nanoparticles for Water Electrolyzer

Electrochemical Deposition Processes for Fabrication of Cathodes/Anodes of Alkaline Water Electrolysis Device

(Invited) Novel Design of Low-Loaded Membrane Electrode Assemblies for Advanced Low-Temperature Water Electrolyzers

Advanced development of anion-exchange membrane electrolyzers for hydrogen production: from anion-exchange membranes to membrane electrode assemblies