Abstract:Abstract Chemical enhanced oil recovery (CEOR) plays a major role in sustaining production, extending the life of field and improves the recoverable reserves which is of economic benefit. The injected polymer will eventually propagate to the production wells where it is co-produced with production fluids. The presence of polymer in the back produced water may increase the residual oil levels and suspended solids in the produced water. This causes production systems bottlenecks, have a detrimental effect on water treatment processes, and increase in Oil in Water levels higher than admissible specs for discharge or reinjection. Several CEOR projects are introduced to producing fields where an established water treatment process already exists. These processes are initially designed to perform under a set of fluid and operating conditions. Polymer breakthrough can change the back produced water characteristics and impact the performance of the process. Upgrading of processes may require substantial investment. Chemical additives are widely considered as pragmatic alternative to improve water quality to desired levels. The selection of chemicals is very important as there are other associated challenges to be considered e.g. of the use of inorganic coagulants such as polyaluminum chloride (PAC) has been shown in studies to generate significant amounts of viscous sludge with low dry solids creating, sludge handing and equipment issues in the field. In this study, a new product combination has been developed to solve some of the drawbacks of traditional chemical such as sludge production while maintaining the performance of treatment. The composition of the product was determined through series of lab experiments and using design of experiments (DOE) methodology. The experiments were initially performed using a synthetic mixture of 400 parts per million (ppm) of hydrolyzed polyacrylamide (HPAM with hydrolysis degree ~ 30%) in saline water. The results were benchmarked to PAC and shown to produce a lower amount of sludge (25-50%) with the same performance in the same range of dosage (300-400 ppm). The sludge generated from the new combined product was also less viscous compared to the benchmark product. The investigation also revealed that a composition containing both inorganic/organic coagulant and cationic polymer improved performance. Results were validated with a field sample containing approx. 300 ppm of HPAM polymer. It was found that to generate less sludge and remove maximum total suspended solids, complete removal of polymer is not required. This new product offers several benefits including a reduction in the operating costs (product dosage is about half of benchmark product, polyaluminum chloride), reduction in the chemical footprint, improves the operational efficiency of the water treatment process and allows to operate within their environmental specifications.

Research of Cationic Polymer on Oily Sewage Treatment in Polymer Flooding Oilfield

[Effects of Polyacrylamide on Settling and Separation of Oil Droplets in Polymer Flooding Produced Water].

Optimization of and Mechanism for the Coagulation–flocculation of Oil-Field Wastewater from Polymer Flooding

The analysis of formation of polymer‐containing oily sludge produced during the wastewater treatment in offshore oilfield

A novel interface-active cationic flocculant for the oil-water separation of oily wastewater produced from polymer flooding

The effect of molecular structure on the properties of cationic polyacrylate and its flocculation‐flotation performance of oilfield oily wastewater treatment

Cumulative Experience With Short- and Long-Term Toxicity to 6-Mercaptopurine in the Treatment of Crohn's Disease and Ulcerative Colitis

The effect of polymer on the floatation-flocculation performance of flocculant for treating polymer flooding produced water

Evaluation of newly developed reverse demulsifiers and cationic polyacrylamide flocculants for efficient treatment of oily produced water

Effect of polyaluminium silicate sulphate with different alkyl chain lengths on oily sewage in oil fields

Preparation of Cationic Polyacrylamide Suspension and Its Application in Oilfield Wastewater Treatment

Influence of suspended microcrystalline polymer system on characteristics of produced water from High Ca and Mg oilfields and corresponding oil removal methods

Study on Activated Sludge Treatment of Polyacrylamide Wastewater from Oilfield

Preliminary research of bio-treatment for sewage produced polymer flooding in oil field

Evaluation of the self-assembled functional PPFS-P-AM composite for treating oilfield sewage

Main Controlling Factors Affecting the Viscosity of Polymer Solution due to the Influence of Polymerized Cations in High-Salt Oilfield Wastewater

Preparation of a selective flocculant for treatment of oily wastewater produced from polymer flooding and its flocculant mechanism

A New Macromolecular Flocculant in the Treatment of Oily Wastewater in Oilfields

Ultrasound-initiated synthesis of cationic polyacrylamide for oily wastewater treatment: Enhanced interaction between the flocculant and contaminants

Study on Flocculant XN98 Treating with Oily Sewage from Polymer Flooding of Oilfield

Optimizing the Performance of Produced Water Chemical Treatment Following CEOR Polymer Breakthrough