Abstract:A phenomenon seemingly unique to hybrid miniemulsion polymerization was observed where monomer conversion would either plateau at a limiting value or quickly switch to a dramatically lesser rate. This phenomenon has been attributed to a combination of three factors. The first factor is the degree to which the monomer and resinous component are compatible. Second is the resultant particle morphology after circa 80% monomer conversion, which roughly corresponds to the portion of reaction where this morphology is established. The third factor is the degree of interaction between the growing polymer and resin (grafting). Of these three, the first two factors were found much more significant in contributing to the limiting conversion. When particle morphology was found to be core/shell, a hard shell (high T-g polymer, PMMA) was found to form a barrier against newly formed initiator radicals derived in the aqueous-phase after appropriate conversion. Residual unreacted monomer solubilized in the resin-dominated particle core was thereafter unreachable by new radicals; hence a limited monomer conversion. In cases where the acrylic polymer (PBA) exhibited a glass transition significantly below the reaction temperature, instead of a core/shell morphology one where the acrylic polymer (and monomer) comprised the continuous particle-phase with small internal resinous island domains was observed. A portion of the monomer concentration was again found to be solubilized within the resin domains, yet in this case newly formed initiator radicals encountered a viscous environment instead of an effective barrier. Rate was found to be limited by the feed of monomer to local polymerization in the continuous particle phase from those resinous islands where residual monomer is solubilized. This is what led to continued polymerization, but at a considerably lesser rate.

Growth of Polymer Nanoparticles in Microemulsion Polymerization Initiated with Γ Ray

Growth of polymer particles in microemulsion polymerization of methyl methacrylate

Graft Copolymerization of Styrene and Acrylonitrile in the Presence of Poly(Propylene Glycol): Particle Growth

Microemulsion Polymerization of Styrene Initiated with Gamma Ray

Microemulsion Seeded Polymerization of Styrene

Ab Initio Emulsion and Miniemulsion Polymerization of Styrene Mediated by a Cyclohexenyl-Functionalized Amphiphilic RAFT Agent

Seeded Microemulsion Polymerization of Butyl Acrylate

Simulation Studies on the Origin of the Limiting Conversion Phenomenon in Hybrid Miniemulsion Polymerization

Micro-emulsion Polymerization of Methyl Methacrylate Initiated with Potassium Persulphate

Formation of Monodisperse PMMA Particles by Radiation-Induced Dispersion Polymerization—i. Synthesis and Polymerization Kinetics

Γ-Ray-initiated Dispersion Polymerization of PMA in Microreactor

Formation of Microporous Polymeric Materials by Microemulsion Radiation Polymerization of Butyl Acrylate

Microemulsion Polymerization of Methyl Methacrylate Initiated with BPO

Formation of Monodisperse Poly(methyl Methacrylate) Particles by Radiation-Induced Dispersion Polymerization. II. Particle Size and Size Distribution

High Monomer Content Batch Microemulsion Polymerization of Butyl Acrylate and Acrylonitrile Initiated with Gamma Ray

Radiation-induced Polymerization of Methyl Methacrylate in Microemulsion with High Monomer Content

Radiation Copolymerization of Acrylamide and Cationic Monomer in an Inverse Emulsion

Fluorescence microscopy tracking of dyes, nanoparticles and quantum dots during growth of polymer spherulites

Effect of Dose Rate on Emulsion and Microemulsion Polymerization of Styrene

Complex-radical Terpolymerization of Styrene, Maleic Anhydride, and N-vinyl Pyrrolidone Via Γ-Ray Radiation: Synthesis, Characterization, and Micellization

Single-Step Confined Growth Of Cdse/Polyacrylamide Nanocomposites Under Gamma-Irradiation