Abstract:Currently, in the two technological approaches for using diesel pilot injection to ignite methanol and partially substituting diesel fuel with methanol, neither can fully achieve carbon neutrality in the context of internal combustion engines. Compression-ignition direct-injection methanol marine engines exhibit significant application potential because of their superior fuel economy and lower carbon emissions. However, the low cetane number of methanol, coupled with its high ignition temperature and latent heat of vaporization, poses challenges, especially amidst increasingly stringent marine emission regulations. It is imperative to comprehensively explore the impacts of the engine geometry, intake boundary conditions, and injection strategies on the engine performance. This paper first investigates the influence of the compression ratio on the engine performance, subsequently analyzes the effects of intake conditions on methanol ignition characteristics, and finally compares the combustion characteristics of the engine under different fuel injection timings. When the compression ratio is set at 13.5, only an injection timing of −30 °CA can initiate methanol compression ignition, but the combustion is not ideal. For compression ratios of 15.5 and 17.5, all the injection timings studied can ignite methanol. Reasonable increases in the intake pressure and intake temperature are beneficial for methanol compression ignition. However, when the intake temperature rises from 400 K to 500 K, a decrease in the thermal efficiency is observed. Particularly, at an injection timing of −30 °CA, both the peak cylinder pressure and peak cylinder temperature are higher, the ignition occurs earlier, the combustion process shifts forward, and the combustion efficiency and indicated thermal efficiency are at higher levels. Furthermore, the overall emissions of NOX, HC, and CO are relatively low. Therefore, selecting an appropriate injection timing is crucial to facilitate the compression ignition and combustion of methanol under low-load conditions.

Combustion Characteristics of SI Engine Fueled with Methanol-Gasoline Blends During Cold Start

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

Combustion and Emission Characteristics of a DI Diesel Engine Fueled by Diesel-Methanol Blends

Experimental Investigation of Cold-Start Unregulated Emissions and Combustion Characteristics of Low-Percent Methanol-Gasoline Engine

Study on Combustion Characteristics of a DI Diesel Engine Operating on Diesel/Methanol Blends

Experimental Investigation on the Emissions of a Port Fuel Injection Spark Ignition Engine Fueled with Methanol–Gasoline Blends

Unregulated Emissions and Combustion Characteristics of Low-Content Methanol−Gasoline Blended Fuels

Measurement of Unregulated Emissions from a Light-Duty Vehicle Fuelled with Low-Proportion Methanol-Gasoline Blends During Cold Start

Research on Emission Characteristics of Methanol-Gasoline Blend Direct Injection HCCI Combustion

Effects of Injection Parameters and EHN Mixing on the Combustion Characteristics of Fueling Pure Methanol in a Compression Ignition Engine

Combustion and Emission Characteristics of Methanol–Diesel Dual Fuel Engine at Different Altitudes

Experimental and numerical study on a SI engine fueled with gasohol and dissociated methanol gas blends at lean conditions

Study on combustion control of a methanol SICI engine

Comparison of efficiency and emission characteristics in a direct-injection compression ignition engine fuelled with iso-octane and methanol under low temperature combustion conditions

Optical investigations on ignition and combustion characteristics of polyoxymethylene dimethyl ethers/methanol blends

Performance of a Methanol-Fueled Direct-Injection Compression-Ignition Heavy-Duty Engine under Low-Temperature Combustion Conditions

Influence of methanol gasoline blend fuel on engine and catalyst performance

Experimental study of effects of exhaust gas recirculation and combustion mode on combustion, emission, and performance of DME‐methanol ‐fueled turbocharged c ommon‐rail engine

Effects of injection and spark timings on combustion, performance and emissions (regulated and unregulated) characteristics in a direct injection methanol engine

Experimental Study on the Combustion and Emission Characteristics of Methanol/Gasoline Fuels in Direct Injection Miller Cycle Gasoline Engines

Influence of ignition timing on performance and emission characteristics of an SI engine fueled with equi-volume blend of methanol and gasoline