The Design of Full-digital Hybrid Electric Vehicle Drive System Based on F2407a DSP Chip

Hu Qingbo,Lv Zhengyu

2006-01-01

Abstract:This paper adopts a Buck+Full_bridge circuit in a 50kW hybrid electric vehicle system. In addition, the control system used F2407a DSP chip can realize motor operation and generator modes. Experimental results prove that this system has good performance and it can be applied in hybrid electric vehicle.

What problem does this paper attempt to address?

Design on Driving System of Hybrid Transducer Type Ultrasonic Motor Based on DSP

FU Ping,WANG Jiang,GUO Ji-feng

DOI: https://doi.org/10.3969/j.issn.1001-6848.2005.02.018

2005-01-01

Abstract:According to the characteristics of driving controlling system of ultrasonic motor,in this paper,a two-phase resonant inverter for driving ultrasonic motor wiht MOSFET is designed,the frequency and phase difference Through the series inductance,we can get good performance of driving wave.
Sensorless Brushless DC Motor Control System Based on DSP

刘勇

DOI: https://doi.org/10.3969/j.issn.1004-7018.2004.01.016

2004-01-01

Abstract:A control system for sensorless brushless DC motor based on DSP is presented.The back-EMF commutation method is used.The start method by means of rotor pre-setting for the brushlese DC motor without position sensor is analyzed in this paper.And the software and hardware design solutions for this system are described.
Design of Speed Control System Based on Fuzzy-PID Hybrid Control for DC Motor

XIAO Jinfeng,SHENG Yifa,XU Zuhua,ZHOU Dao

DOI: https://doi.org/10.3969/j.issn.1001-6848.2011.05.015

2011-01-01

Abstract:In this paper,a new hybrid speed regulating method based on Fuzzy-PID was proposed.It can be used in the speed loop for speed and current closed loop control DC motor control system.When the error between reference speed and real speed is bigger than some threshold value,uses the fuzzy control.But when the error reduces to the threshold value below,changes the PID adjustment.The simulation research on the hybrid speed regulating system of DC motor was carried out.The simulation results show that the system based on this hybrid speed regulating has better dynamic and static performance than the system based on PID speed regulating.A speed control system of DJ23 DC motor used in DDSZ-1 electrical machinery and electrical technology test installation was introduced.The system based on this new hybrid speed regulating method has a control unit of the single-chip Atmega128,using PWMcontrol signal to control DC motor.The results of experiment show that the system is of better robustness and strong practicality and simple structure.
Analyses and Design of a High Power Bidirectional 48V-12V DCDC Converter System for Electric Vehicle Application.

Hai Liu,Lenian He

DOI: https://doi.org/10.1109/iecon48115.2021.9589662

2021-01-01

Abstract:This paper proposes the theoretical analyses, design method, design process and design results of a high power bidirectional 48V-12V DCDC converter system in electric vehicle (EV) application. The design is divided into 3 levels that are topology level, control method level, and block level based on IC with 3 steps respectively. In topology level, full-bridge CLLC is chosen for its high efficiency and good stability. 8 stages are designed for full-bridge CLLC in one switching period. Topology design mainly focuses on determining resonant components by inherent frequency and quality factor. In control method level, FPD (Frequency, Phase shift, and Duty) influence the performance of the whole system in their own way and FPD control method is chosen for this system. In block level, a main control loop that consists of 3 interlaced loops is illustrated by functional blocks and achieved actually by IC design. The whole design is verified by analog IC simulation whose results confirm the basic function and expected performance of the system. The output voltage accuracy enters 0.1% range and efficiency is up to 99.15% in buck mode with full load. The performances of the converter system in other conditions are also competitive.
Study on the Vehicle Controller of Hybrid Electric Vehicle Based on Fuzzy Logic

Zhang Dawei,Wu Shijing,Luo Xiaohua,Ren Hui

DOI: https://doi.org/10.1109/mace.2010.5535693

2010-01-01

Abstract:This paper describes a kind of Parallel Hybrid Electric Vehicle (PHEV) with the torque and speed alternating-coupled planetary gear and Continuously Variable Transmission (CVT). By improving PHEV mode-transformation efficiency, it is easy to achieve the goal of improving fuel-economy and reducing emissions. The main components of the Vehicle Controller such as fuzzy control units, assistant control units and components control units are researched and designed successfully in the use of relative hardware and software based on the fuzzy logic control strategy of maximal state of charge of the battles, in order to realize real-time control of PHEV.
Design of Fuzzy Control System for PMSM Based on DSP

WANG Tengda,WANG Zhengshi

DOI: https://doi.org/10.3969/j.issn.1001-6848.2013.06.008

2013-01-01

Abstract:In application of fuzzy PID control,the paper designed a new servo system for permanent magnet synchronous motor.In the proposed scheme,DSP TMS320F2809 was used as the controlling center and IPM was designed as the hardware foundation.The control system uses the classic double-loop structure,the current loop is vector control strategy and the position loop is self-adaptive fuzzy PID controller.In the traditional PID control system,when the PMSM fast startup or shutdown,accelerate or decelerate,it always shows up high overshoot or slow dynamic response problems.By experimental testing and comparing,it is proved that this controlling system can provide significant improvement on these problems.
Design of Experimental Switched Reluctance Drive System Based on DSP

周春,潘再平

DOI: https://doi.org/10.3969/j.issn.1006-7167.2004.04.016

2004-01-01

Abstract:The paper introduced a method to design a small power SRD for experimental teaching by the basic principle of SRD and the characteristics of a serial of DSP——TMS320LF2407. The experimental system can satisfy the request of experiment teaching for SRM.
Design of a 300 Kw Partial Power Processing Based DC-DC Converter for Electric Vehicles Extreme Fast Charging Stations

Bin Guo,Xin Zhang,Zhengqing Zhang,Hao Ma,Xiang Jin,Yongmao Wang

DOI: https://doi.org/10.1109/peac56338.2022.9959484

2022-01-01

Abstract:This paper proposes a design approach of a partial power processing (PPP) based dc-dc converter for electric vehicle extreme fast charging stations. The partial power converter is made up of two stages: the front-end stage is an input-series output-parallel (ISOP) LLC converter, which acts as a dc-dc transformer (DCX). The rear-end stage is a three-phase interleaved buck converter to realize flexible constant current/voltage (CC/CV) charging control. With the proposed topology structure, only less than one fifth of the total charging power is processed. Thus, compared with full rated charging converters, its efficiency and power density are significantly improved. The operation principles with modulation strategy is presented in depth. In addition, a simple control strategy is proposed to realize current-sharing control of the three-phase interleaved buck converter. The system design approach is provided in detail. Finally, simulation and experimental tests on a 300-kW prototype validate its appropriate performance.
Hybrid Electric Vehicles Battery Management System Based On Dsp

Xuan Zhiyuan,Gao Dawei,Wei Jieyuan,Cao Jianhua

2010-01-01

Abstract:The paper researches on the design of Battery Management System (BMS) used in parallel hybrid electric vehicles. After analyzing the function desired in BMS, the author confirms a digital standard to stand by in the after design. Using the software PRETEL and Code Composer Studio 3.3, the hardware and software design are carried out. The article mainly forces on the function of DSP TMS320F28335 produced by TI Company in order to use its several function models properly. At last, the experiments in laboratory and 40001cm road test provide enough evidences that the BMS is accurate and stead-going Copyright Form of EVS25.
Design of a Three-Phase Hybrid Stepping Motor Pulse Subdivision Controller Based on DSP

Gangfeng Yan

2007-01-01

Abstract:Hybrid stepping motor is similar to permanent magnet synchronous motor in functional principle,therefore,it can be controlled by the advanced control technology of permanent magnet synchronous motor.A new control method is obtained from control at aspect of synchronous motor instead of control of phase currency.A three-phase hybrid stepping motor pulse subdivision controller based on TMS320LF2407 DSP is designed based on this theory.
Design of Vehicle Control Unit Based on DSP for a Parallel HEV

Weimin Li,Guoqing Xu,Hang Tong,Yangsheng Xu

DOI: https://doi.org/10.1109/ical.2007.4338827

2007-01-01

Abstract:This paper presents a DSP based vehicle control unit (VCU) for hybrid electric vehicle (HEV). Digital Signal Processor (DSP) based real time controller plays a key role in HEV system operation. It provides an efficient platform to run complex optimization algorithms for energy management strategy. First, the hardware design of VCU is introduced in detail. Then software design of VCU and C code automatic generation technical based on RTW are discussed. A flexible and configurable method is described to automatically deploy the Simulink-model into the VCU. Experimental results have demonstrated the reliability of hardware design and flexibility of software design of the proposed VCU.
Vector Control System of PMSM Based on DSP

Rongxiang Zhao

2006-01-01

Abstract:Permanent magnet synchronous motor(PMSM) gradually becomes the most popular executive component in high performance serve system.Vector control system of PMSM based on TMS320F240 was presented,and the design of hardware and software were also introduced.
An Open-loop Vector Microstepping Drive System of Two Phase Hybrid Stepping Motor Based on DSP

QU Liang,QIU Jianqi,SHI Cenwei

DOI: https://doi.org/10.3969/j.issn.1001-6848.2011.05.016

2011-01-01

Abstract:An open-loop vector microstepping drive system of two phase hybrid stepping motor was built.In order to modulate the current of two phase windings,two H-bridges were controlled by PWM based on DSP in terms of software.Dead time compensation must be added,according to the principle of PWM on DSP.This paper talked about the principle of the system,the frame of the structure and the scheme of realization.From the result,the system has a good performance,and can be easy to control.
MC56F8013 Digital Signal Processor and Its Applications in Brushless DC Motor Control System

Wei Zhang

2008-01-01

Abstract:In this paper,the core and peripheral blocks of Freescale MC56F8013 DSP is presented.And this paper introduces the CodeWarrior IDE and PC Master briefly as well.A brushless DC motor control system with speed closed-loop is put forward,aiming at its advantages in motor control.And the experiment results show that the design of hardware and software is valid and practical.
Fault Tolerant Permanent Motor Drive System Based on DSP28069

wang zhuang,zhao wenxiang,ji jinghua,zhu jihong

DOI: https://doi.org/10.3969/j.issn.1673-6540.2014.08.001

2014-01-01

Abstract:A control hardware system was built for permanent magnet motor,in which DSP28069 is core controller,and CPLD plays supplementary role. In the whole system,DSP and CPLD send commands to each phase.The proposed fault-tolerant drive was constituted of H-bridge. Phase current,rotor position and speed were acquired by using Hall current sensor and resolver respectively. Schmitt trigger and CPLD were combined to avoid overcurrent.The output voltage and phase current were measured by the speed and current dual-loop control in which a three-phase9 /6 pole permanent magnet motor was drived. The experimental results show that the designed hardware system is safe,reliable and practical.
New space vector PWM drive for the control of two-phase BLDC

Chun-hong LU,Wei ZHANG

DOI: https://doi.org/10.3969/j.issn.1001-4551.2017.01.014

2017-01-01

Abstract:Aiming at the low utilization rate of dc voltage H-bridge inverter and the complicated structure and the poor economic effect of double-H-bridge inverter in the control of two-phase BLDC,study on the inverter and the control strategy of two-phase BLDC was carried out,and a space vector pulse-width modulation(SVPWM) system of two-phase BLDC which used six-switch inverter was proposed.A two-phase BLDC control system which used double close loops of speed and current control was simulated through Matlab/Simulink.The control performance and the dc voltage utilization rate were tested by using PSoC.The results indicate that the system can realize the quick control of speed and the current of two-phase BLDC,and improve the utilization rate of bus voltage.The method is proved to be of great significance.
Remote Networked Motor Control System Based on DSP

DU Xin-hu,HAN Zhi-xia,YANG Jian-hua

DOI: https://doi.org/10.3969/j.issn.1000-8829.2007.12.011

2007-01-01

Abstract:A design of remote networked motor control system based on DSP is presented,and the drive circuit,position detection,commutating control and electrocircuit protection are discussed,and the hardware circuit is designed.In the module of network communication,the hardware circuit of embedded remote network communication based on the Ethernet controller CS8900A is designed.This design has simple circuit,high reliability and good value of application.
Design of AC Drive System Based on DSP TMS320F2812

HUANG Da-wei,ZHANG Wen-kai,YU Ai,YANG Geng

DOI: https://doi.org/10.3969/j.issn.1000-100x.2005.02.001

IF: 5.967

2005-01-01

IEEE Transactions on Power Electronics

Abstract:The paper presents the configuration of control board based on DSP TMS320F2812,which is used in motion control system,discusses some details in the designing hardware and programming with C language,and finally,provides experimental results of the system.Great attention has been paid to specialties of TMS320F2812 power supply system and A/D modle in hardware.C language program is used for designing the software.It is of benefit to modularization,mainte-nance and transplant of software by usage of DSP′s high operation ability and its variant internal and external resources.Parts of experimental results show the feasibility of design.
DSP-based Drive System for Transverse Flux and Linear Switched Reluctance Motor

Nan ZHAO,Bao-ming GE

DOI: https://doi.org/10.3969/j.issn.1000-128x.2006.06.009

2006-01-01

Abstract:The control system based on TMS320LF2407A is proposed for the drive system of transverse flux and linear switchedreluctance motor (TFLSRM), making full use of the rich interface resources and the fast calculation speed of DSP. In the light of the runningrequirement of the TFLSRM, automatic reciprocating movement is realized with position detection of linear motor. The test results verify thedesign target. The linear motor automatically reciprocating moves in the secondary track and realizes efficiently the 4qs movement.
A Ship Electric Propulsion Control System Based on DSP

SU Feng-fei,QIU A-rui

DOI: https://doi.org/10.3969/j.issn.1000-100x.2007.05.015

IF: 5.967

2007-01-01

IEEE Transactions on Power Electronics

Abstract:This paper introduces a Permanent Magnetic Synchronous Motor(PMSM) control system for ship electric propulsion.Based on Digital Signal Processor(DSP) of TMS320LF2407,the system is composed of hardware and software.The hardware completes the tasks of sampling,drive,protection etc.And the software carries out calculations for vector control,PI adjustment,Space Vector Pulse Width Modulation(SVPWM) etc.Experimental results indicate that the controller can run steadily and the timing effect is well,which provides a feasible scheme for ship electric propulsion control system.

The Design of Full-digital Hybrid Electric Vehicle Drive System Based on F2407a DSP Chip

Design on Driving System of Hybrid Transducer Type Ultrasonic Motor Based on DSP

Sensorless Brushless DC Motor Control System Based on DSP

Design of Speed Control System Based on Fuzzy-PID Hybrid Control for DC Motor

Analyses and Design of a High Power Bidirectional 48V-12V DCDC Converter System for Electric Vehicle Application.

Study on the Vehicle Controller of Hybrid Electric Vehicle Based on Fuzzy Logic

Design of Fuzzy Control System for PMSM Based on DSP

Design of Experimental Switched Reluctance Drive System Based on DSP

Design of a 300 Kw Partial Power Processing Based DC-DC Converter for Electric Vehicles Extreme Fast Charging Stations

Hybrid Electric Vehicles Battery Management System Based On Dsp

Design of a Three-Phase Hybrid Stepping Motor Pulse Subdivision Controller Based on DSP

Design of Vehicle Control Unit Based on DSP for a Parallel HEV

Vector Control System of PMSM Based on DSP

An Open-loop Vector Microstepping Drive System of Two Phase Hybrid Stepping Motor Based on DSP

MC56F8013 Digital Signal Processor and Its Applications in Brushless DC Motor Control System

Fault Tolerant Permanent Motor Drive System Based on DSP28069

New space vector PWM drive for the control of two-phase BLDC

Remote Networked Motor Control System Based on DSP

Design of AC Drive System Based on DSP TMS320F2812

DSP-based Drive System for Transverse Flux and Linear Switched Reluctance Motor

A Ship Electric Propulsion Control System Based on DSP