Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Advance in Kinetics Model of Diesel Hydrodearomatization Reaction

Kinetic Model for Hydroisomerization Reaction of C8-aromatics

Kinetic model for hydroisomerization reaction of C<sub>8</sub>-aromatics

Kinetic Model and Simulation Analysis for Toluene Disproportionation and C9-Aromatics Transalkylation

Eight Lumps Kinetic Model for Residual Oil Catalytic Cracking

Lumped Kinetics Model and Its On-Line Application to Commercial Catalytic Naphtha Reforming Process

Kinetics toward mechanism and real operation for ultra‐deep hydrodesulfurization and hydrodenitrogenation of diesel

Modeling and Order Reduction for the Thermodynamics of a Diesel Oxidation Catalyst with Hydrocarbon Dosing

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Enhancement of the Ammonia Kinetic Mechanism for Nitrogen-Based Pollutant Chemistry

The Influence of Hydrodearomatisation Reaction Kinetics on the Modelling of Sulphur and Aromatics Removal from Diesel Fuel in an Industrial Hydrotreating Process

MODELING OF HYDROTREATING PROCESSES VIA MOLECULAR F EED RECONSTRUCTION AND MOLECULE-BASED MONTE CARLO KINET ICS

Hydrogen solubility prediction for diesel molecules based on a modified Henry equation

Reduced Kinetic Mechanism of N‐heptane Oxidation in Modeling Polycyclic Aromatic Hydrocarbon Formation in Diesel Combustion

Introduction of adsorption, deactivation and dehydrogenation descriptors to promote the single-event kinetics model composed of elementary steps catalogued by the carbenium ions type for ethylene oligomerization and aromatization

Chemical Kinetic Model for Polycyclic Aromatic Hydrocarbon Formation During Gasoline Surrogate Fuel Combustion

Assessment of H2-CH4-air Mixtures Oxidation Kinetic Models Used in Combustion

Modeling of Soot and Polycyclic Aromatic Hydrocarbons in Diesel Diffusion Combustion

Simplified modeling of butane dehydrogenation: deeper understanding of the system's dynamics

A simplified chemical kinetic model with a reaction mechanism based on a multidimensional average error iteration method for ammonia and ammonia/hydrogen combustion

Detailed and Simplified Kinetic Models of N-Dodecane Oxidation: the Role of Fuel Cracking in Aliphatic Hydrocarbon Combustion