Abstract:Single-pass equal channel angular extrusion (ECAE) experiments of an extruded Mg–Zn–Y–Zr alloy with an intense initial basal texture were performed in two inter-perpendicular billet orientations and at 473 and 623K. The study was aimed to determine the effects of ECAE temperature and billet orientation on the microstructure, texture evolution and mechanical properties of the ECAEed alloy. It was found that the grain refinement achieved through the single-pass ECAE in the Orient-I billet orientation (the normal direction (ND) of the extruded plate parallel with the ECAE exit direction) was more effective than that in the Orient-II billet orientation (the ND of the extruded plate perpendicular to the ECAE exit direction). The average grain sizes after ECAE at 473K were much smaller than those after ECAE at 623K. The pole figures of the alloy ECAEed at 473K showed that most of the basal planes in the Orient-I and Orient-II samples were inclined about 40° and 35°, respectively, with respect to the longitudinal direction of the ECAE extrudate. However, for the alloy ECAEed at 623K, most of the basal planes were parallel with the longitudinal direction of the ECAE extrudate. It was remarkable that the yield strengths of the alloy ECAEed at 473K were lower than those at 623K. The peculiar relationship between ECAE temperature and the mechanical properties of the alloy was ascribed to the texture evolution during ECAE.

Influence of Equal Channel Angular Extrusion on the Properties of Mg-6Al Alloy

Preparing Mg-6Al alloy with high mechanical properties and fine grains by equal channel angular extrusion

Effect of Equal Channel Angular Extrusion on the Microstructure and Mechanical Properties of AZ31 Magnesium Alloy

The Microstructure and Mechanical Properties of AZ31 Mg Alloy Processed by Two-Step Equal Channel Angular Extrusion

Microstructure and mechanical properties of AZ31 Mg alloy processed by two-step equal channel angular extrusion

Mechanical Properties and Microstructure of AZ31 Mg Alloy Processed by Two-Step Equal Channel Angular Extrusion

Effect of Solution Treatment on Microstructure Evolution and Mechanical Properties of Mg-6.0Zn-0.6Y-0.5Zr Alloy Processed by Equal Channel Angular Extrusion

A Study of Microstructure Evolution for Mg Alloy Subjecting to Multi-Pass Equal Channel Angular Extrusion

Microstructure and Mechanical Properties of Cu–10%Al–4%Fe Alloy Produced by Equal Channel Angular Extrusion

Effect of equal channel angular extrusion process on deformation behaviors of Mg-3Al-Zn alloy

Microstructure Evolution and Mechanical Properties of AZ 31 Mg Alloy Processed by Equal Channel Angular Extrusion

Experimental and Numerical Investigation on Pure Aluminum by ECAP

Effect of ECAE Conditions on the Microstructure, Texture and Mechanical Properties of an Extruded Mg–Zn–Y–Zr Alloy

Enhancing Room Temperature Mechanical Properties of Mg–9Al–Zn Alloy by Multi-Pass Equal Channel Angular Extrusion

The effect of texture on the mechanical properties of AZ31 MG alloy by equal channel angular extrusion

Effect of Mechanical Properties of Cu-10 % Al-4 % Fe Alloy Prepared by Equal Channel Angular Extrusion

Microstructure Evolution of Processed Mg-Al-Zn Alloy by Equal Channel Angular Extrusion in Semi-Solid Isothermal Treatment

Effects of ECAE Temperature and Billet Orientation on the Microstructure, Texture Evolution and Mechanical Properties of a Mg–Zn–Y–Zr Alloy

Uniformity and Continuity of Effective Strain in Az91d Processed by Multi-Pass Equal Channel Angular Extrusion

Study on the Effect of the ECAP Deformation on the Organization and Properties of the Extruded Mg-Sn-Al Alloys

Effect of extrusion-ECA integrated large strain technology on microstructure and properties of 7075 aluminum alloy