Abstract:This paper aims to review our recent results on the microstructure and mechanical properties of nanocrystalline and nanoquasicrystalline alloys in Al-based system obtained by rapid solidification. The nanocrystalline alloys consist of nanoscale fcc-Al particles with a particle size of 3 to 5 nm embedded in an amorphous matrix. The homogeneous dispersion of the nanoscale fcc-Al particles caused the remarkable increase in tensile fracture strength (sigma(f)) by about 1.4 times as compared with those for the corresponding amorphous single phase and the highest value reached as high as 1560 MPa. The high sigma(f) has been interpreted to result mainly from the extremely high sigma(f) of the Al particles caused by the absence of internal defects, based on the result that no internal defects are observed in the nanoscale Al particles. The nanoquasicrystalline alloys are composed of spherical icosahedral (I) particles with a particle size of 10 to 50 nm surrounded by an Al layer with a thickness of about 10 nm and the volume fraction of the I-phase is as high as about 70 %. The nanoquasicrystalline base alloys exhibit high sigma(f) reaching 1350 MPa combined with good bending ductility. The internal structure is interpreted to consist of a new nonequilibrium phase with a short-range disorder and long-range I-structure by high-resolution TEM. The formation of the unique nonequilibrium structure is presumed to be the origin for the achievement of high sigma(f) and good ductility. It is also shown that the bulk I-based alloys produced by extrusion of the atomized I-based powders exhibit high sigma(f) of 500 to 850 MPa and large epsilon(f) of 6 to 25 %. These properties are excellent enough to demonstrate the validness of the structure control to nanocrystalline and nanoquasicrystalline phases.

A SAXS study of rapidly solidified Al-base amorphous alloys containing nanometer-scale precipitates

Nanometer-Scale Structure of Rapidly Solidified Al<SUB>92</SUB>V<SUB>3</SUB>Fe<SUB>3</SUB>Zr<SUB>2</SUB> Alloy

Structure and Mechanical Strength of Al-V-Fe Melt-Spun Ribbons Containing High Volume Fraction of Nanoscale Amorphous Particles

Microstructure and Novel Properties of Nanocrystalline and Nanocrystalline Alloys Prepared in Al-Based Systems by Rapid Solidification

The Crystallization Kinetics Study of Finemet-Co Amorphous Alloys

Formation And High Strength Of Nanoamorphous Structure In Rapidly Solidified Al-Cr-Co-Ce And Al-V-Fe Alloys

Microstructural Characteristics and Electrical Resistivity of Rapidly Solidified Co-Sn Alloys

Present State and Future Prospect of Rapidly Solidified Aluminum-based Alloys.

Microstructure of Rapidly Solidified High Strength Al94V4Fe2 Alloy

Development of High Specific-Strength Al-Based Alloys by the Use of Rapidly Solidified Amorphous and Quasicrystalline Powders.

High-Strength Al-V-M (m=fe, Co or Ni) Alloys Containing High-Volume Fraction of Nanoscale Amorphous Precipitates

Change in the Nano-Structure of Al-base Alloy Ribbons in Response to Tensile Stress – a Small-Angle X-ray Scattering Study

Microstructural characterization of a rapidly solidified Al–10 Sb alloy

High Mechanical Strength of Al–(V, Cr, Mn)–(Fe, Co, Ni) Quasicrystalline Alloys Prepared by Rapid Solidification

Formation and High Mechanical Strength of Al-Based Alloys Containing A Nanoscale Icosahedral Phase As A Main Constituent

X-ray Diffraction Study of Amorphous Al 77.5 Mn 22.5 and Al 56 Si 30 Mn 14 Alloys

SAXS analysis of rapidly solidified Al92V3Fe3Zr2 ribbon

Microstructure of a Rapidly Solidified Al–4V–2Fe Ultrahigh Strength Aluminum Alloy

MICROSTRUCTURES OF RAPIDLY SOLIDIFIED Al-In IMMISCIBLE ALLOYS

Crystallization and High Mechanical Strength of Al-Based Amorphous Alloys

Microstructural Characterization of Rapidly Solidified Al90ce10 Alloy