Abstract:One dimensional (1D) and three dimensional (3D) ultrasound sources were applied to modulate the solidification process of FeCoCrNi2.1Al high entropy alloy whose liquidus temperature is up to 1614 K with the acoustic signal in liquid alloy in-situ measured. It was found that 1D ultrasound significantly refined the lamellar eutectic structure by decreasing both the eutectic cell width and the aligned alpha(B2)/gamma(FCC) phase spacing. If ultrasound amplitude and dimension were increased, lamellar eutectic gradually transformed into anomalous eutectic without synergetic orientation. Meanwhile, a metastable sigma phase enriched with Cr precipitated from gamma phase in anomalous eutectic under 3D ultrasounds. Based on the combined analysis of eutectic structural evolution and sound field characteristics, the ultrasonic solidification mechanism was further clarified. The promoted depen-dent nucleation by stable cavitation and the fast growth rate caused by acoustic streaming were the main reasons for the significantly refined eutectic structure under 1D ultrasound. The induced independent eutectic nucleation and growth by transient cavitation, together with the enhanced solute and thermal diffusion by the intensive acoustic streaming under 3D ultrasounds were responsible for the formation of anomalous eutectic and the precipitation of metastable sigma phase. The maximum ultimate strength and total elongation under ultrasound were simultaneously increased by 28% and 93%, showing comprehensive mechanical performance superior to those prepared by conventional approaches. The prominent strain hardening in gamma phase and increase in alpha/gamma interfaces induced by refining effect were the strengthening mechanisms, and the improvement of ductility was attributed to the intensified strain hardening in gamma phase.

Structure and Mechanical Strength of Al-V-Fe Melt-Spun Ribbons Containing High Volume Fraction of Nanoscale Amorphous Particles

Synthesis and high mechanical strength of Al-based alloys consisting mainly of nanogranular amorphous particles

Synthesis, microstructure and thermal stability of novel Al-V-Fe alloy powders by mechanical alloying

Microstructure Control and Micromechanical Property Enhancement of CoCrFeNiZr 0.5 Alloy under Melt Quenching and Electrostatic Levitation Conditions

Effect of Sn and Al Additions on the Microstructure and Mechanical Properties of Amorphous Ti–Cu–Zr–Ni Alloys

The Crystallization Kinetics Study of Finemet-Co Amorphous Alloys

Fabrications and mechanical properties of bulk amorphous, nanocrystalline, nanoquasicrystalline alloys in aluminum-based system

Ultrasounds Induced Eutectic Structure Transition and Associated Mechanical Property Enhancement of FeCoCrNi2.1Al High Entropy Alloy

The phase structure and electrochemical properties of the melt-spun alloy Zr0.7Ti0.3Mn0.4V0.4Ni1.2

Preparation of Al-based bulk amorphous alloys and properties of Al/Al-Fe-V amorphous composites

Structure and mechanical properties of Mg85Cu5Zn5Y5 amorphous alloy containing nanoscale particles

Microstructure of Amorphous and Nanocrystalline Al_(65)Si_(35)Alloy Prepared by Supercooling

Nano-amorphous—crystalline Dual-Phase Design of Al80Li5Mg5Zn5Cu5 Multicomponent Alloy

High-Strength Nanotwinned Al Alloys with 9R Phase

Structure and mechanical behavior of ultrafine-grained aluminum-iron alloy stabilized by nanoscaled intermetallic particles

Microstructure and Mechanical Behavior of a Novel Co20Ni20Fe20Al20Ti20 Alloy Fabricated by Mechanical Alloying and Spark Plasma Sintering

An investigation on the microstructural stability of rapidly solidified AlFeVSi alloy ribbon

Structure and Properties of Nanostructured A357 Alloy Produced by Melt Spinning Compared with Direct Chill Ingot

Mechanical Properties of Bulk Amorphous Zr-Al-Cu-Ni-Ag Alloys Containing Nanoscale Quasicrystalline Particles

Structure of melt—spun Al—2.5Ti—2.5Fe—2.5V alloy and structural changes during annealing

Microstructure and correlated mechanical properties study of Ni-(Fe, Co)-Mn-(Al, In) as-spun ribbons