Abstract:<p>We present a multi-level delumping method suitable for thermal enhanced oil recovery processes. At low pressures, the temperature variable is the most critical factor impacting the displacement process through viscosity reduction and evaporation/condensation effects. Hydrocarbon components are vaporized under high temperatures, move downstream in the gas phase and condense back to the liquid phase. That process is governed by the <em>K</em>-values of the components, evaporating out of the liquid phase sequentially with increasing temperatures. To reduce the computational cost, it is standard practice to reduce the number of (pseudo-)components used in thermal reservoir simulation. Depending on the number and type of hydrocarbon pseudo-components retained in the simulations, we may not be able to capture the correct displacement due to large errors in the lumped phase behavior (flash) computations. We address that problem through a multi-level method: we use data obtained from a short simulation using the most detailed fluid description available, and leverage that information to guide a delumping process. We use temperature as a proxy variable for composition, and select reference temperatures. We extract the corresponding reference compositions from the detailed run and use them to extend the lumped pseudo-components to an approximate detailed composition. We compute the phase mole fractions as well as the gas compressibility factor. We test our method using six heavy oil samples, and under two different recovery processes: hot nitrogen injection and in-situ combustion (air injection and exothermic oxidation reactions). The average error on the liquid mole fraction is reduced by 4-12 times (depending on the oil samples) compared to the flash using pseudo-components, and the maximum error by 6-48 times. We illustrate that the method is amenable to manually adding more information about the physics of some oil samples. We also discuss how to efficiently pick the reference temperatures. For uniformly sampled temperatures (between a minimum and maximum temperature), we conduct a sensitivity study which led us to use six temperatures. We ran both local (Pattern Search, PS) and global (Particle Swarm Optimization, PSO) gradient-free optimization methods. PS is able to find the closest local minimum to the uniform set, giving a limited improvement of 6.5%. The known increased cost for PSO is worth the investment in at least one of the cases we considered, leading to a 67% improvement.</p>

Adaptive Mesh Refinement Method for Thermal Recovery of Heavy Oil with Light Component Using Steam Injection

DESIGNING AND DEVELOPING AMR SOFTWARE PACKAGE FOR RESERVOIR NUMERICAL SIMULATION INTHERMAL RECOVERY OF HEAVY OIL BY STEAM INJECTION

WOA with Adaptive Mutation Operator to Estimate Parameters of Heavy Oil Thermal Cracking Model

Adaptive Mesh Refinement for Heat Transfer Problems in Electronic Devices

Adaptive mesh refinement algorithm for steam injection process in complex faulted reservoir

Adaptive Mesh Refinement For One-Dimensional Three-Phase Flow With Phase Change In Porous Media

Numerical simulation of bitumen recovery via supercritical water injection with in-situ upgrading

Pore-scale Experimental Study on EOR Mechanisms of Combining Thermal and Chemical Flooding in Heavy Oil Reservoirs

Experimental and simulation studies on steam stimulation with multiple fluids for offshore heavy oil reservoirs

Numerical Modelling of Hybrid Steam and In-Situ Combustion Performance for Oil Sands

Theoretical Insight into the Effect of Steam Temperature on Heavy Oil/Steam Interface Behaviors Using Molecular Dynamics Simulation

Multi-level delumping strategy for thermal enhanced oil recovery simulations at low pressure

Enhanced Oil Recovery and in Situ Upgrading of Heavy Oil by Supercritical Water Injection

Experimental and numerical investigation on extra-heavy oil recovery by steam injection using vertical injector -horizontal producer

Study of Multi-component Thermal Fluid Recovery on Offshore Heavy Oilfield in Bohai Bay of China

Analysis for Flow and Heat Transfer of Thermal Recovery Well with Steam and Multiple Thermal Fluids Injection

A Semi-Compositional Approach to Model Asphaltene Precipitation and Deposition in Solvent-Based Bitumen Recovery Processes

Numerical Simulation of the Effect of Light Component Volatility on Heavy-Oil Production by Steam Injection

Adaptive Mesh Refinement Method for Speeding Up Numerical Simulation of Electroslag Remelting Process

Thermal Hydraulic Analysis Using GIS on Application of HTR to Thermal Recovery of Heavy Oil Reservoirs

Experimental Investigation and Numerical Simulation of Dynamic Characteristics for Multithermal Fluid-Assisted SAGD in Extraheavy Oil Reservoir