Abstract:The preparation process-dependent phase morphology of blends composed of nylon 6 and acrylonitrile-butadiene-styrene (ABS) over a composition range of 30-70 wt% using a styrene-maleic anhydride (SMA) copolymer as the compatibilizing agent with a constant content (5phr) was investigated. The results of the scanning electron microscope (SEM) observation revealed that compared with the binary blends of nylon 6 and ABS, the existence of SMA caused a composition shift of phase inversion to a higher weight fraction of nylon 6 when ABS was blended with the preblended nylon 6/SMA blend, while the co-continuous structures could be observed over a considerably narrower composition range when nylon 6 was blended with the pre-blended ABS/SMA blend. An examination through dynamic mechanical analysis (DMA) tests confirmed the results obtained with SEM. It is found that near the phase inversion region a remarkable change in the dynamic storage modulus (G') and the loss tangent (tan delta) appears. Moreover, the influence of blending sequence on the size of dispersed particles has been probed for uncompatibilized and compatibilized blends of nylon 6 and ABS over a wide range of compositions below or beyond the phase inversion points. For the blends of ABS dispersed in a nylon 6 matrix, little discernible effects of blending sequence on particle size could be observed. Furthermore, there exists a significant difference in morphologies of the blends prepared by nylon 6 particles dispersing in a ABS matrix in cases of different blending sequences used. Some possible factors responsible for the above asymmetric behaviors have been proposed.

Fractal Analysis of Morphology of PE/PA Blends: Composition

Morphology Development in Multi-Component Polymer Blends: I Composition Effect on Phase Morphology in PP/PET Polymer Blends

Analysis of phase morphology and dynamics of immiscible PP/PA1010 blends and its partial-miscible blends during melt mixing from SEM patterns

The Fractal Analysis in Q Space for the Phase Morphology of Polypropylene/Polydecamethylene Sebacamide Blends During Melt Mixing

Multifractal Analysis on Dispersion of Immiscible High-Density Polyethylene/Polystyrene Blends Processed Via Polymer Vane Plasticating Extruder

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Research Progress of Dispersed Phase Morphology of HDPE/PA Blends

Ultrasonic characterization of phase morphology of high density polyethylene/polyamide 6 blend melts

The Effects of Dispersed Phase Morphology Induced by Flow on the Bulk Viscosity of HDPE/PA Blends

Molecular Dynamics of Different Polymer Blends Containing Poly(2,6-Dimethyl-1,4-phenylene Ether).

The Effect of Blending Sequence on Phase Morphology of Nylon 6/abs/sma Blends

Morphologies and Mechanical Properties of Syndiotactic Polypropylene (spp)/ Polyethylene (PE) Blends

Multifractal Analysis of the Fracture Surfaces of Foamed Polypropylene/polyethylene Blends

Fractal analysis on compatibilization of PP-g-MAH in PP/PA 6 blending system

Development of Dispersed Phase Size and Its Dependence on Processing Parameters

Morphology and Dynamic Mechanical Properties of High Density Polyethylene/petroleum Resin/polyethylene–octylene Elastomer Blends

Investigation on Morphology Development of PP/PA6 Blend along Single Screw Extruder

Morphology and Rheology of PP/POE Blends in High Shear Stress Field

Effect of Epdm-G-Mah on the Morphology and Properties of Pa6/Epdm/Hdpe Ternary Blends

Investigation on Phase Separation Kinetics of Polyolefin Blends Through Combination of Viscoelasticity and Morphology.

Prediction of Phase Morphology of PP/POE/PA6 Ternary Blend and Influence by Mixing Sequence