Abstract:As one of the important load-bearing components of a truck, the drive axle housing must meet the requirements of stiffness and strength. The traditional design method uses redundancy design to meet the performance requirements. The joint design between the three-dimensional mathematical model and finite element model is adopted, and the optimal design of the drive axle housing is realized based on topology optimization and multiobjective optimization. Firstly, the static analysis of the drive axle housing of a rear axle drive truck was carried out with four typical working conditions. It was concluded that the four working conditions all operate under the yield limit of the material, and it was found that the maximum equivalent stress of the four working conditions occurs at the step of the half-shaft casing. Among the four working conditions, the most critical one is the maximum vertical force working condition. Then, based on the maximum vertical force working condition, the fatigue life analysis is conducted, and the minimum fatigue life appears at the transition position of the half-shaft sleeve and the arc transition position of the main reducer chamber. The remaining parts can meet the design requirements. The overall safety factor of the drive axle housing is mainly between 1 and 5 when operating under this working condition. Then, through modal analysis, the first to sixth natural frequency and vibration modes of the drive axle housing are extracted. Based on the modal analysis, the dynamic characteristics of the drive axle housing are further studied by harmonic response analysis and random vibration analysis. Finally, two kinds of lightweight optimization schemes for the drive axle housing are given. Topology optimization reduces the mass of the drive axle housing by 17.4%, but the overall performance slightly decreases. Then, the five dimensional parameters of the drive axle housing are selected as design variables. The mass, maximum deformation, equivalent stress, service life, and the first-, second- and third-order natural frequencies are defined as objective functions. Through the optimal space-filling design method, the experimental designs are performed and the sample points are obtained. Based on the results of experiment design, the multiobjective genetic algorithm and response surface method are combined to optimize the objective functions. The analysis results show that the mass is reduced by 4.35%, the equivalent stress is reduced by 21.05%, the minimum life is increased by 72.28%, and the first-, second-, and third-order natural frequency are also increased to varying degrees. Two different optimization strategies are provided for the design of the drive axle housing.

Optimization and Experimental Research on a New-Type Short Cylindrical Cup-Shaped Harmonic Reducer

Study and Performance Test of Full Complement Cycloidal Ball Reducer with Ceramic Balls as its Gear Teeth

Deformation and stress analysis of short flexspline in the harmonic drive system with load

Solid Modeling And Finite Element Analysis Of Harmonic Drive With Wide Slot Involute Tooth Profile

Analysis of the Partial Axial Load of a Very Thin-Walled Spur-Gear (Flexspline) of a Harmonic Drive

Circular Spline Tooth Longitudinal Modification Design and Contact Analysis for Harmonic Drives with Short Flexspline

Modeling and Fatigue Characteristic Analysis of the Gear Flexspline of a Harmonic Reducer

Contact Analysis for Short Harmonic Reducer in Robotic Joints

Non-circular Interference Fit Analysis in Harmonic Reducer Based on Sequential Assembling and Loading Simulation

Double-circular-arc tooth profile design and parametric analysis on the comprehensive performance of the harmonic drive

Design and Testing of a New Type of Planetary Traction Drive Bearing-Type Reducer

A novel method based on mechanical analysis for the stretch of the neutral line of the flexspline cup of a harmonic drive

Dynamic design and transmission performance analysis based on CF/PEEK composite for short flexspline harmonic drive

Influence of cycloid pinwheel reducer structure parameters on transmission performance and optimized design with considering friction loss

Optimization Design of the Composite Hub Connection Structure Based on ANSYS Software Technology

Contact analysis of output mechanism of cycloidal pinwheel reducer

A harmonic drive model considering geometry and internal interaction

Sensitivity Analysis of Cup-shaped Flexible Gear Parameters to Its Stress Based on ANSYS

Topology Optimization and Multiobjective Optimization for Drive Axle Housing of a Rear Axle Drive Truck

Double-stage multi-objective optimized design for cycloid pinwheel reducer based on genetic algorithm

Deformation Analysis of the Flexspline of Harmonic Drive Gears Considering the Driving Speed Effect Using Laser Sensors