Design of A Ka Band Circular Polarization Mircostrip Array

Feng Tao,Fu Yuan

DOI: https://doi.org/10.3969/j.issn.1008-8652.2006.03.013

2006-01-01

Abstract:Based on principle of resonance mircostrip multiplex power divider,a design method of standing-wave circular polarization mircostrip array is provided through analyzing design of a Ka band and simulation result of the design is also summarized.

What problem does this paper attempt to address?

A High Gain Circularly Polarized Microstrip Array Antenna At Millimeter-Wave Band

Youjian Hu,Qingwen Deng,Xiaojun Ying,Siyi Shen,Yuming Zeng,Zhiwei Xu

DOI: https://doi.org/10.1109/GSMM53250.2021.9511956

2021-01-01

Abstract:This paper presents the design of a <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$\mathrm{4} \times \mathrm{4}$</tex> elements circularly polarized microstrip patch array at millimeter-wave band. The sequential rotation method and series-parallel feed network are employed in the power distribution circuit for antenna performance improvement. The feed network is integrated on the same substrate layer of the antenna array in order to facilitate processing and manufacturing, and the total size of the design is <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$\mathrm{10} \text{mm}\times \mathrm{12} \text{mm}\times \mathrm{0.127} \text{mm}$</tex> . The simulated return loss exhibits an impedance bandwidth of 7%, and the 3-dB axial ratio bandwidth of 10% with respect to 78.5 GHz is obtained. Besides, the maximal gain is 17.6dBi at 78.5GHz.
Design of Circular/Dual-Frequency Linear Polarization Antennas Based on the Anisotropic Complementary Split Ring Resonator

Hui Zhang,You-Quan Li,Xi Chen,Yun-Qi Fu,Nai-Chang Yuan

DOI: https://doi.org/10.1109/tap.2009.2029400

IF: 5.7

2009-01-01

IEEE Transactions on Antennas and Propagation

Abstract:A novel kind of circular polarization and dual-frequency linear polarization microstrip antennas is proposed. The designs are based on the anisotropic property of the complementary split ring resonator. When the complementary split ring resonator is etched on the patch of the probe-fed microstrip antenna, the gap orientation asymmetric or symmetric to the current propagating direction will render the antenna to radiate circular polarization waves or dual-frequency linear polarization waves. Details of the experimental results compared with the simulated results are presented and discussed.
Design of Circular Polarisation Microstrip Patch Antennas with Complementary Split Ring Resonator

H. Zhang,Y. -Q. Li,X. Chen,Y. -Q. Fu,N. -C. Yuan

DOI: https://doi.org/10.1049/iet-map.2008.0346

2008-01-01

Abstract:A novel design of circular polarization microstrip patch antenna based on the complementary split ring resonator is evaluated numerically and experimentally verified. Unlike the previous application of its resonant performance, the non-resonant property of complementary split ring resonator is used as an asymmetric perturbation to excite the square microstrip patch antenna for a good circular polarization radiation. Good agreement is observed between the measurement and simulation results.
Compact dual-band circularly polarized microstrip patch array

Yan HE,Changjiang DENG,Zhenghe FENG,Hu YANG

DOI: https://doi.org/10.11887/j.cn.201606030

2016-01-01

Abstract:A dual-band circularly polarized patch array using a sequential-phase feeding network was presented.The array includes four metal patches and a metal square ring.Each rectangle patch was cut in diagonal corners,and was excited by feeding lines on the edge.The feeding lines are microstrip which are connected to the middle metal square ring.In addition,four patches are rotated arrangement.The middle mental square ring is not only a feeding network which provides increasing phase for circularly polarization,but also a radiator which enhances the performance of the array.With this feeding way,the patch array just has single-layer substrate and it is compact.In addition,it radiates circularly polarized patterns in two working bands.Through fabrication,test and measurement,the -10 dB impedance bandwidth of the patch array is 5. 17 GHz~5. 59 GHz and 5. 99 GHz~6. 27 GHz.The measured 3 dB AR bandwidth is 5. 19 GHz~5. 49 GHz and 6. 1 GHz~6. 18 GHz.
A Ka-Band Monopulse Microstrip Antenna Array

Huang Hai-Yan,Wang Bing-Zhong,Li Feng,Zhao Lu

DOI: https://doi.org/10.1109/IMWS.2008.4782278

2008-01-01

Abstract:A 1 times 8 monopulse microstrip patch antenna array in Ka-band has been proposed. The radiating element is a modified circular patch antenna, designed for getting circular polarization. The feed network is composed of six Wilkinson power dividers, a 3 dB hybrid, and a microstrip to waveguide transition. Both the array and the feed network are placed on the same layer.
Ka-Band Wide-Angle Scanning Phased Array with Dual Circular Polarization

Lei Zhang,Jianyong Yin

DOI: https://doi.org/10.3390/electronics13122238

IF: 2.9

2024-06-08

Electronics

Abstract:A wide-angle scanning phased array with dual circular polarization in the Ka-band is presented in this paper. To improve the scanning capability of the phased array, the microstrip element is modified by loading many metal posts at its center and periphery. In addition, a stripline coupler is designed to achieve dual circularly polarized (CP) radiation, and the inner conductor of the subminiature micro-push-on (SSMP) connectors for feeding the coupler is extended to the top layer of the multilayer element by introducing an open stub, which simplifies the assembly process between the SSMP connector and multilayer printed circuit board (PCB) due to through-hole soldering instead of blind-hole soldering. The proposed element can cover a frequency range from 28 GHz to 30.5 GHz with a relative bandwidth of 8.5% in the Ka-band. An 8 × 8 phased array is constructed based on this proposed element, and a wide-angle scanning range from −65° to +65° is obtained for the dual circular polarization. The proposed array has a gain fluctuation of 5.1 dB and an axial ratio (AR) of less than 3.3 dB during beam-steering. The prototype is fabricated and measured, with a good agreement between the measured and simulated results. The proposed phased array can be applied in a Ka-band millimeter-wave (MMW) communication system.

engineering, electrical & electronic,computer science, information systems,physics, applied
A Low‐cost, Wideband, Dual‐circularly Polarized Traveling Wave Antenna Array

Jin Liu,Jia-Lin Li

DOI: https://doi.org/10.1002/mmce.22532

IF: 1.987

2021-01-01

International Journal of RF and Microwave Computer-Aided Engineering

Abstract:This article presents a low-profile dual-circularly polarized array based on the series feed and sequential rotation techniques. The basic radiation element is the microstrip based corner-cut square patch that could achieve dual-circularly polarized radiations. By rotating four basic elements in sequence to constitute a 2 x 2 subarray and series feeding with a phase difference of 90 degrees, the axial ratio bandwidth can be greatly enhanced. Further, by symmetrically positioning four of such 2 x 2 subarrays coupled with out-of-phase feeding of the four subarrays, the beam deflection against frequency is corrected. To validate the proposed design, an 8 x 8 dual-circularly polarized array operating at 6.0 GHz was developed and examined experimentally. Measurements and simulations confirm the design well.
Design and Measurement of A Circularly Polarized Ka-Band Reflectarray Antenna

Ang Yu,Fan Yang,Atef Z. Elsherbeni,John Huang

2009-01-01

Abstract:Reflectarray antennas are composed of phased elements to mimic conventional curved reflectors. An important step of the reflectarray antenna design is the selection of array elements, whose performance strongly determines the system behavior. This paper compares the bandwidth, fabrication tolerance, and design flexibility characteristics of several types of elements for Ka-band operation. Based on this investigation, a Ka-band circularly polarized reflectarray antenna is designed and a prototype is fabricated and measured in a planar near field measurement system. This designed antenna provides a possible choice for the sub-array of a recently developed single-layer multi-band reflectarray antenna.
A Ka-Band Circularly-Polarized Filtering Antenna Array with A Hybrid Feeding Network

Ling-Feng Zhang,Lin-Sheng Wu,Jun-Fa Mao

DOI: https://doi.org/10.1109/iws52775.2021.9499509

2021-01-01

Abstract:A circularly-polarized filtering antenna array is designed in 23~27.5 GHz. Its hybrid feeding network is built up hybridly with stripline and air-filled substrate integrated waveguide (AFSIW) structures, for both antenna efficiency and design flexibility. The filtering response is achieved by stacked patch radiators, embedded stripline lowpass filters, the AFSIW network and a substrate integrated waveguide bandpass filter. The stripline-fed 4×4 subarrays are fabricated and measured. For the whole 16×16 array, the simulated in-band realized gain is 23.03~26.31 dBi, the out-of-band suppression is higher than 23.29 dB, and the x-polarized suppression is better than 31.13 dB.
Design of a Ka/Ku Dual-Band Dual-Polarized Array

Lin Yi,He Yan,Manyuan Dai,He Wang,Hu Yang

DOI: https://doi.org/10.1109/apcap.2014.6992499

2014-01-01

Abstract:In this paper, with the application of dielectric resonator antennas(DRA), a novel design of a shared-aperture dual-band dual-polarized (DBDP) array working in the Ka/Ku bands is proposed. At Ka-band, aperture-coupled microstrip patches are selected as the radiating elements. At Ku-band, Crossed dielectric resonator antennas(DRA) are selected as the radiating elements. The array which comprises 2×2 Ku-band elements interleaved with 4×4 Ka-band elements is discussed in detail. The antenna array proposed here is able to be scaled to a larger radiating aperture.
A Single Layer Broadband Circularly Polarized Reflectarray Based On The Element Rotation Technique

Ang Yu,Fan Yang,Atef Z. Elsherbeni,John Huang

DOI: https://doi.org/10.1109/APS.2009.5171594

2009-01-01

Abstract:This paper investigates the performance of the single slot ring element for Ka-band reflectarray designs. Using the element rotation technique, two Ka-band circularly polarized reflectarray prototypes are designed and implemented, with different thicknesses of the substrate. The bandwidth is significantly enhanced when a thick substrate is used.
Design of A Low-Profile Dual-Band Shared-Aperture Circularly Polarized Phased Array

Wendong Liu,Yuanxi Cao,Juan Chen,Sen Yan

DOI: https://doi.org/10.1109/lawp.2023.3329153

IF: 4.2

2023-01-01

IEEE Antennas and Wireless Propagation Letters

Abstract:A dual-band circularly polarized phased array is proposed for satellite communications. The low-band and high-band radiators are realized by a circular slot etched on a substrate integrated waveguide (SIW) and a magnetoelectric (ME) dipole positioned at the center and the corners of the SIW, respectively. The low-band design combines two modes with broadside radiation patterns and a wide axial ratio (AR) bandwidth. The measurement of the array with four low-band and seven high-band elements demonstrates that both the -10 dB impedance bandwidth and the 3 dB AR bandwidths of broadside beams can cover 12.5-14.2 GHz and 16.8-18.5 GHz for the low and high band, respectively. For broadside beams, the 3 dB AR beamwidths in the phi = 0° plane are 76° and 32° at 13 and 18 GHz, respectively. For maximum scanning beams, the ARs within the 3 dB beamwidth are below 3 dB and 4.6 dB at 13 and 18 GHz, respectively.

telecommunications,engineering, electrical & electronic
A Broadband Low-Profile Dual-circularly Polarized Reflect-Array Based on A Single-layer Microstrip Patch for Ka -Band Application

Xi Wang Dai,Yu Hui Zhang,Weiliang Yu,Leilei Liu,Guo Qing Luo

DOI: https://doi.org/10.1109/tap.2023.3249119

IF: 5.7

2023-01-01

IEEE Transactions on Antennas and Propagation

Abstract:A broadband low-profile dual-circularly polarized (dual-CP) reflect-array (RA) cells covering both K- and Ka-bands is presented in this article. As an anisotropic impedance surface, the functional layer is designed based on a multi-resonant structure and printed on a substrate with a thickness of 0.762 mm. The circuit is composed of an elliptical ring, arc-shaped and rectangular metal microstrip lines. The air layer between the functional layer and the metal plate can effectively extend the cell bandwidth (BW), and the overall profile is 1.8 mm. The dynamic phase and Berry phase can be adjusted by changing the size of the arc-shaped microstrip lines and the rotation of the cells. The diffraction results show that the phase of left-handed (LH) circularly polarized (CP) and right-handed (RH) CP waves can be controlled independently and reflected by high purity with the cross-polarization BW of 64% (19.72 $sim $ 38.44 GHz). A dual-CP RA with 1013 cells is designed to realize reflect beams at $ heta $ = −20° for LHCP wave and $ heta $ = 15° for RHCP wave at 30 GHz. Furthermore, the 3 dB gain BW can cover the Ka-band and is expected to be used in wireless and satellite communication systems.

telecommunications,engineering, electrical & electronic
An X-Band Circularly Polarized Reflectarray Using Split Square Ring Elements And The Modified Element Rotation Technique

ang yu,fan yang,atef z elsherbeni,john huang

DOI: https://doi.org/10.1109/APS.2008.4619758

2008-01-01

Abstract:Using split square ring elements and the modified element rotation technique, an X-band circularly polarized reflectarray is designed and implemented through microstrip technology. At 8.4 GHz, the reflectarray prototype has a gain of 30.4 dB and an aperture efficiency of 53.7%. The fractional axial ratio bandwidth is 6%, while the 3 dB gain bandwidth is 7%.
A Dual-fed Multi-Layer Circularly-polarized Microstrip Antenna for Phased Array

闫鹏,李阳,李振海,白旭东,金荣洪,耿军平,梁仙灵

DOI: https://doi.org/10.3969/j.issn.1673-5692.2012.01.015

2012-01-01

Abstract:A planar dual-back-fed circularly-polarized microstrip antenna is proposed based on the air mi- crostrip structure. The element has 13% impedance bandwidth and the axial ratio of maximum radiation direction is 2.5 dB. Based on the element design, a rotationally symmetric four-element array is also de- signed. Furthermore, in order to verify the circularly-polarized beam scanning characteristics of antenna array, an eight-element array is composed by eight elements and two power splitters to realize the beam pointing to the normal direction and 30° deviation respectively. The antenna owns good circular polarization axial ratio and is easy for beam scanning, which is very suitable for the active phased array applications.
Design Of A Dualband Omnidirectional Planar Microstrip Antenna Array

K. P. Wei,Z. J. Zhang,Z. H. Feng

DOI: https://doi.org/10.2528/PIER11112101

2012-01-01

Abstract:This paper proposes and designs a new method of dualband omnidirectional planar microstrip antenna array. A cascade of transposed microstrip lines have been adapted to produce effective antenna structures that radiate omnidirectionally, with high efficiency, low reflection, and useful radiation patterns. In this paper, the antenna structure has been found to have low-pass characteristics due to the periodic discontinuities at the transposed junctions. The analysis and design of the low-pass characteristic are performed according to the filter theory of periodic structures and full-wave simulation. Therefore, a relatively higher frequency radiating array is appropriately designed with a low-pass filtering attribute, which prevents the lower frequency radiators from resonating at the relatively higher frequency. An air gap between adjacent transposed sections is proposed in order to enhance impedance matching, and a fork shape stub at the end is used as a virtual short point to enhance radiation at the higher frequency. Finally a single port dualband omnidirectional antenna array is obtained by locating the higher frequency radiating array with low-pass filtering attribute near the antenna feed and a relatively lower frequency radiating array at the end. An example of a dualband omnidirectional planar array is demonstrated experimentally, which operates at 2.32 similar to 2.56 GHz and 5.65 similar to 6.10 GHz with S-11 < -10 dB and a stable radiation pattern, and corresponding gains of 7.0 similar to 7.6 dBi and 6.9 similar to 7.9 dBi respectively.
Study on Circularly Polarized Antenna and its Phased Array

XIAO Shao-qiu,ZHAO Liang,RAN Min,WANG Bing-zhong

2010-01-01

Abstract:Wide-angle circularly polarized antenna and its array can be applied extensively to vehicle,aircraft and airborne radar systems.It is used to receive or transmit electromagnetic wave in large space range.This paper presents a wide-angle circular polarized microstrip antenna element,and a 1×4 element linear array is designed by the elements.The array has some advantages,such as,compact size,light weight and wide-angle scanning with circular polarization radiation characteristics.
Design of a Wideband Meander-Line Circular Polarizer for Ka-band Applications

REN Wang,WU Xi-dong,LIU Guo-dong

2012-01-01

Abstract:This paper proposes a new approach to design circularly polarized antennas for Ka-band millimeter-wave satellite communications.Circular polarization can be obtained through the use of a meander-line polarizer(MLP) located in front of a linearly polarized horn antenna without any internal changes.It can be compatible with existing linearly polarized millimeter-wave antenna seamlessly with the advantages of low cost,low design complexity and high flexibility.The influences of the MLP parameters on antenna axial ratio are investigated by parametric studies using CST.The antenna is fabricated and tested.Using the proposed method,a circularly polarized antenna with an axial ratio(AR) lower than 3dB over the 27.5-32.5GHz frequency band can be achieved.
Design of a High Efficiency Low Sidelobe Dual-Polarization Cavity Antenna Array at Ku-band

Shan Jiang,Qingyuan Zhang,Chang Chen,Zhiping Yin,Weidong Chen

DOI: https://doi.org/10.1109/apusncursinrsm.2018.8608700

2018-01-01

Abstract:A 16 × 4 dual-polarization antenna array with high efficiency and low sidelobe is designed. To achieve good radiation efficiency, cavity antenna is used in this work as the basic element and stripelines are utilized to form the feeding networks. The feeding circuits for exciting different polarizations are stacked and carefully weighted. The simulated results show that the bandwidths of VSWR <; 1.6 for both of the polarizations are about 7.89% (14.6GHz-15.8GHz) and the isolation between the two ports is better than 40dB. In addition, 63% radiation efficiency (center frequency) with higher than 25.5dB gain is achieved.
8-Element circularly polarized microstrip array antenna

Qianqian Wu,Jingzhao She,Zhenghe Feng

DOI: https://doi.org/10.1109/ICMMT.2008.4540412

2008-01-01

Abstract:In this paper, the development of an eight-element circularly polarized microstrip array at 5.8 GHz is presented. Theory and experiment demonstrate both axial ratio 3 dB bandwidth and the voltage standing wave ratio (VSWR) 2:1 bandwidth of 8.6%. Different half power beamwidth at horizontal plane (16deg) and vertical plane (36deg) is achieved, and the measured array peak gain is 14 dBi at center frequency. The sequential rotation method for the element arrangement and array arrangement is employed to meet these objectives. The use of coplanar corporate feeds for microstrip patch arrays leads to constructional simplicity.

Design of A Ka Band Circular Polarization Mircostrip Array

A High Gain Circularly Polarized Microstrip Array Antenna At Millimeter-Wave Band

Design of Circular/Dual-Frequency Linear Polarization Antennas Based on the Anisotropic Complementary Split Ring Resonator

Design of Circular Polarisation Microstrip Patch Antennas with Complementary Split Ring Resonator

Compact dual-band circularly polarized microstrip patch array

A Ka-Band Monopulse Microstrip Antenna Array

Ka-Band Wide-Angle Scanning Phased Array with Dual Circular Polarization

A Low‐cost, Wideband, Dual‐circularly Polarized Traveling Wave Antenna Array

Design and Measurement of A Circularly Polarized Ka-Band Reflectarray Antenna

A Ka-Band Circularly-Polarized Filtering Antenna Array with A Hybrid Feeding Network

Design of a Ka/Ku Dual-Band Dual-Polarized Array

A Single Layer Broadband Circularly Polarized Reflectarray Based On The Element Rotation Technique

Design of A Low-Profile Dual-Band Shared-Aperture Circularly Polarized Phased Array

A Broadband Low-Profile Dual-circularly Polarized Reflect-Array Based on A Single-layer Microstrip Patch for Ka -Band Application

An X-Band Circularly Polarized Reflectarray Using Split Square Ring Elements And The Modified Element Rotation Technique

A Dual-fed Multi-Layer Circularly-polarized Microstrip Antenna for Phased Array

Design Of A Dualband Omnidirectional Planar Microstrip Antenna Array

Study on Circularly Polarized Antenna and its Phased Array

Design of a Wideband Meander-Line Circular Polarizer for Ka-band Applications

Design of a High Efficiency Low Sidelobe Dual-Polarization Cavity Antenna Array at Ku-band

8-Element circularly polarized microstrip array antenna