Abstract:Background: The band and loop space maintainer is used to maintain the missing space of deciduous molars which are lost early. When the second deciduous molar is lost prematurely, the stress on the first permanent molar during different degrees of development may vary when it is the abutment. The design and use of the space maintainer may also lead to damage of the loop. The purpose of this article is to use the finite element method to study the stress on the first permanent molar and the loop with or without occlusal contact, with the first permanent molar of four different degrees of development serving as the abutment. We aimed to guide the clinical design and use of the space maintainer. Methods: We developed finite element models of the mandibular first permanent molar and the band and loop space maintainer, and simulated alveolar bone, periodontal ligament (PDL), enamel and dentin. The four developmental stages were 1/2 (I), 2/3 (II), 3/4 (III) and full development (IV). Ansys Workbench was used to analyze the effects of root development and occlusal contact between the loop and the opposite jaw on abutment teeth and the loop. Abutment teeth were statically loaded vertically and obliquely with a force of 70 N. The loop was statically loaded vertically with a force of 14 N. The stress on all structures and the displacement trends of the loop were calculated. Results: The stress on enamel, dentin, PDL and alveolar bone were similar, and the concentration was consistent. But if there was occlusal contact, the loop produced maximum displacement at the near middle edge of contact with the anterior teeth. When the loop was in occlusal contact with the opposing occlusal tooth, the peak value of the equivalent stress on the space maintainer under vertical load was: group I > group IV > group III > group II, and the maximum principal stress peak change was: group I > group III > group II > group IV. The change of the equivalent stress peak value of the loop under oblique load was: group I > group III > group IV > group II, and the maximum principal stress peak change was: group III > group I > group II > group IV. When the loop was not in occlusal contact with the opposing occlusal tooth, the peak value of the equivalent stress on the space maintainer under vertical load was: group IV > group I > group II > group III, and the maximum principal stress peak change was: group IV > group I > group II > group III. The change of the equivalent stress peak value of the space maintainer under oblique load was: group I > group IV > group II > group III, and the maximum principal stress peak change was: group I > group IV > group II > group III. Conclusions: Our results suggested that whenever possible, choosing the teeth with nearly complete root development as the abutment of the space maintainer is advisable. The design and use of the band and loop space maintainer should avoid occlusal contact with the occlusal teeth to prevent deformation of the loop.

Effect of Loop Configuration on Appliance Stiffness of Stainless Steel Round Wire

Influence of Fluoride-Containing Acidic Artificial Saliva on the Mechanical Properties of Nickel-Titanium Orthodontics Wires.

[Comparison of Mechanical Properties on Different Phase Transformation Points of Nickel-Titanium Orthodontic Wires].

Modeling and Experimentation of the Unidirectional Orthodontic Force of Second Sequential Loop Orthodontic Archwire

Establishment, FEM Analysis and Experimental Validation of Tooth Movement Prediction Model of Orthodontic Archwire T-loop

Orthodontic Force Prediction Model of T-loop Closing Spring Based on Dynamic Resistance Model

Bending Property Analysis and Experimental Study of Orthodontic Wires

Synergistic Effect of Wire Bending and Salivary Ph on Surface Properties and Mechanical Properties of Orthodontic Stainless Steel Archwires

A theoretical analysis on mechanical character of multiloop edgewise arch wire

Load-deflection characteristics of superelastic and thermal nickel-titanium wires

Stress induced on permanent mandible first molar and space maintainer under normal masticatory forces: a finite element study

Stress change of periodontal ligament of the anterior teeth by using a torque preadjusted arch wire of lingual appliance: a 3-dimensional finite element analysis

[Design of nonlinear locking mechanism for shape memory alloy archwire of miniature orthodontic device]

[Three-Dimensional Finite Element Analysis of the Biomechanical Effects of Multiloop Edgewise Archwire (MEAW)].

Mechanical properties and clinical applications of orthodontic wires

Novel approach for characterizing clinical load application of superelastic orthodontic wires

Stiffness and frictional resistance of a superelastic nickel-titanium orthodontic wire with low-stress hysteresis

Experimentation and Simulation of Second Sequential Loop Orthodontic Moment Prediction Modeling

Effect of different combinations of bracket, archwire and ligature on resistance to sliding and axial rotational control during the first stage of orthodontic treatment: An in-vitro study

Multiloop Edgewise Archwire Therapy Techniques Analysis Using Three-Dimensional Finite Element Analysis

THREE DIMENSIONAL MECHANICAL ANALYSIS FOR THE ORTHODONTIC FORCES OF ORTHODONTIC WIRES