Abstract:In this paper, the modal strain energy index for detecting damaged diagonal member(s) of an offshore jacket structure using partial modal information is investigated. Only the first two mode shapes, with merely horizontal translational degree of freedoms (DOF) in each mode, are utilized in the damage detection procedure. Meanwhile, the damage detection with mass change on the deck of the platform model is also considered. First a numerical model of an offshore jacket structure as baseline (pre-damaged) is developed by a finite element method. Several damages are simulated by reducing the elastic modulus of the structural element(s). Then the modal strain energy method is applied to detect the damaged location(s). Numerical results demonstrated that this damage detection method only uses a few lower modes and partial DOF of the whole structure, and can detect the damaged location(s) when the deck mass is changed. stiffness, damping or mass of the structure, and so as to change the modal parameters such as modal frequencies and mode shapes. That is to say, changes of modal parameters can be used as a damage indicator. The advantage of vibration based damage detection is the use of ambient vibration as excitation. The interference of the detection process to the normal operation of the structure can be minimized. Furthermore, vibration based damage detection makes it possible online structural health monitoring. Cawley and Adams (1979) proposed a method of predicting the site of damage based on changes in the natural frequencies. Salawu (1997) reviewed the detection of structural damage through changes in frequency: The main idea of this type of method is based on the premise that the ratio of frequency in two modes is a function of the damage location only, if changes in stiffness are independent of frequency. Positions where this theoretically determined ratio equals the experimentally measured value are therefore possible damage sites. But changes in frequencies can only be used to identify the mere existence of damage. In other words, the frequencies generally cannot provide spatial information about structural changes. Mayes (1992) presents a method for model error localization based on mode shape changes. Damage typically is a local phenomenon. Local response is captured by higher frequency modes whereas lower frequency modes tend to capture the global response of the structure and are less sensitive to local changes in a structure. From a testing standpoint it is more difficult to excite the higher frequency response of a structure as more energy is required to produce measurable response at these higher frequencies than at the lower frequencies. An alternative to using mode shapes to obtain spatial information about vibration changes is using mode shape derivatives, such as curvature. Pandey et. al. (1991) demonstrated that absolute changes in mode shape curvature could be a good indicator of damage for the FEM beam structures. But Salawu and Williams (1994) demonstrate that the curvature change does not typically give a good indication of damage using experimental data. They point out that the most important factor is the selection of which modes are used in the analysis. Another class of damage identification methods uses the dynamically measured

Damage Detection of A Circular Cylindrical Shell with Frequency Sensitivities

DAMAGE DETECTION FOR AN AXIAL SYMMETRICAL SHELL STRUCTURE

Damage Detection of Composite Structures Using Dynamic Analysis

Damage Detection Method for Cylindrical Structure Using Guided Waves

Damage Detection in Cylindrical Shell Structures with Wavelet Analysis

Damage Detection of an Offshore Jacket Structure from Partial Modal Information: Numerical Study

Damage Detection for an Elastic Thin Plate Based on Gauss Curvature Modal Difference

Damage Detection Using Modal Frequency Curve and Squared Residual Wavelet Coefficients-Based Damage Indicator

Damage Detection of Mono-Coupled Periodic Structures Based on Sensitivity Analysis of Modal Parameters

Output-Only Damage Identification Using Enhanced Structural Characteristic Deflection Shapes and Adaptive Gapped Smoothing Method

A Methodology for Evaluating Damage in Thin-Walled Cylindrical Shells Using Bounded Ultrasonic Beam Scattering

Robust Structural Damage Detection and Localization Based on Joint Approximate Diagonalization Technique in Frequency Domain

Theory and Simulation of Damage Detection in Reticulated Shell

Complex Damage Detection Method Based on CMSE and NicheGA

Adaptive mesh refinement for finite element analysis of the free vibration disturbance of cylindrical shells due to circumferential micro-crack damage

A Damage Detection Method: CMSE Combined with Niche GA

Internal Damage Localization for Large-Scale Hollow Cylinders Based on Helical Sensor Network

Strain energy numerical technique for structural damage detection.

Assessment of Structural Damage Using Natural Frequency Changes

Damage Detection in Coupled String System by Measured Dynamic Responses

Vibration-Based Damage Detection with Structural Modal Characteristics