Abstract:The article presents the results of studies of the process of obtaining granular materials from high-strength aluminum alloys of the Al - Zn - Mg - Cu system by centrifugation of the melt with ultra-high cooling rates of granules. The concept of a «steam jacket» is introduced, namely, a steam layer that occurs between the granule body and the cooling liquid, which prevents the intensity of heat removal and is an obstacle to increasing the crystallization rate due to the lower thermal conductivity of water vapor. It is established that the formation of a vapor layer always occurs due to the heating of the cooling liquid in contact with the melt drop to boiling temperatures and the transition of the cooler from the liquid phase to steam. The technology of increasing the rate of crystallization of granules due to the constant removal of the vapor layer is proposed. The removal (knocking down) of the vapor shell that occurs around the drop occurs due to the high speed of the drop movement in the cooling medium. Fundamentally important in the industrial implementation of this technology is not so much the design of the device for obtaining pellets by centrifugation of the melt, namely, the high required rotation speed of the spraying crucible of the device under consideration. The results of experimental data are presented to determine the necessary rotation speed of the perforated cup, which ensures the creation of a sufficient initial velocity of the drop movement, leading to a constant churning of the «steam jacket». It is determined that an increase in the rates of heat removal from the crystallized granules and, as a result, an increase in the crystallization rate leads to an increase in the strength characteristics of granular aluminum alloys of the Al-Zn-Mg-Cu system. In particular, in the production of pressed semi-finished products from alloys of the Al-Zn-Mg-Cu system, such as B95, B96c. the increase in the strength characteristics of the material of the press products is up to 15 % compared to the same granular materials obtained by traditional methods with industrial crystallization rates of melt droplets. It is established that this method, based on the removal of the vapor layer around the formed granule, is the only possible one for further increasing the cooling rate and, as a result, the crystallization rate. Reducing the size of granules to the size of powders leads to serious technological problems in the further consolidation of granules and, in fact, is a dead end branch of the further development of granulation methods.

Characteristics of Melted Sulphur Granulation Process in a Water Cooling Tower for Spherical Particles

A granulation process for producing spherical particles of a rubber antioxidant in a water cooling tower

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

Ultralow Adhesion and Phase Change Behaviors of Sulfur Droplets on the Superhydrophobic Surface and Its Application in the Granulation Process

A Novel Granulation Technology for Producing Spherical Wax Particles

Heat Transfer Characteristics of High-Temperature Particle Population in Ultra-Dilute Phase: Particle-fluid-surface Heat Transfer During Falling

Cooling and phase evolution of a molten blast furnace slag particle

Investigation on Unsteady Phase-Change Heat Transfer Characteristics of Centrifugal Granulated Particles

Water Removal from Wax Particle Surface by Gas Shear Flow

The Heat Transfer Characteristics of Semi-molten Wide Sieving Dilute Phase Particles Between Vertical Heating Surfaces

Granulation by Spray Coating Aqueous Solution of Ammonium Sulfate to Produce Large Spherical Granules in a Fluidized Bed

Characteristics of flight trajectory and heat transfer of liquid steelmaking slag droplet during air quenching granulation process

Experimental investigation on granulation characteristics and waste heat recovery of molten slag in gas quenching dry granulation technique

Granulation mechanism of gas quenching blast furnace slag with different basicities

Optimizing heat transfer and solidification crystallization in dry granulation of blast furnace slag

Effects of Granulator Structure and Cooperating Mode with Slag Tube on the Centrifugal Granulation Characteristics of Molten Slag

The Fluidity and Sprayability Characteristics of -200 Mesh Sulfur Powder

Numerical Investigation of Breakup Process of Molten Blast Furnace Slag Through Air Quenching Dry Granulation Technique

Investigation of the features of crystallization of granules of high-strength aluminum alloys of the Al-Zn-Mg-Cu system at ultra-high cooling rates

Copper sulfides agglomeration using a novel lab-scale granulator: Integrated evaluation of bonding, leaching and mechanical behavior

Granulation Effect Analysis of Gas Quenching Blast Furnace Slag with Different Basicities