Abstract:It is highly desirable to undercool titanium based alloy melts and modulate their dendritic solidification process due to the relevant applications in aerospace engineering. But the serious chemical reactivities of this category of alloys result in potent heterogeneous nucleation and suppress remarkable undercoolings in the course of normal material processing. This paper shows that such a challenge can be solved by containerless processing approach. Liquid Ti-25 wt.%Al alloy is highly undercooled and rapidly solidified under containerless state by both electromagnetic levitation and drop tube techniques. Its metastable undecoolability, crystal nucleation mechanism and dendrite growth process are examined experimentally and analyzed theoretically. Those heterogeneous nuclei with wetting angles above 60 are found to be quite difficult to eliminate even during levitation processing, thus reducing the undercoolability of this alloy. The maximum undercooling of bulk alloy melt reaches 210 K (0.11 TL). The thermodynamic driving force to initiate the nucleation of -Ti phase increases almost linearly with the enhancement of undercooling. The phase dendrite displays a growth velocity up to 11.2 m/s, indicating that the rapid solidification is realized at the relatively slow cooling rate of levitated alloy melt. With the increase of undercooling, phase dendrite experiences a kinetic transition from solute diffusion controlled to thermal diffusion controlled growth. Once undercooling exceeds 100 K, the nonequilibrium solute trapping effect brings about the practically desirable segregationless solidification. Nevertheless, the single condition of substantial undercooling is insufficient to suppress the solid state transformation of phase. It is decomposed into 2-Ti3Al phase plus a small amount of -TiAl compound after containerless solidification at levitated state. A more efficient approach to controlling and modulating the solidification microstructures is to utilize the coupled effects of high undercooling and rapid quenching, which proves to be feasible through the rapid solidification of alloy droplets inside drop tube. For those alloy droplets with diameters ranging from 77 to 1048 m, their cooling rates attain a maximum of 1.05105 K/s, and the predicted maximum undercooling is 227-778 K. In this case, phase dendrites are well refined and kept in a metastable state until ambient temperature. The heat transfer calculations indicate that the thermal radiation is the dominant cooling mechanism for the large alloy droplets above 690 m, whereas thermal convection becomes the major cooling mechanism for the small alloy droplets below 690 m. The microgravity condition during free falling does not show apparent effect on the microstructural formation of these alloy droplets.

Cooling And Crystallization Of Molten Aluminum Alloy Drops In Water

Analysis of features of heat transfer processes during crystallization of aluminum alloy granules in aqueous and water-vapor media

Investigation of the features of crystallization of granules of high-strength aluminum alloys of the Al-Zn-Mg-Cu system at ultra-high cooling rates

Observation of Dendrite Growth Velocity and Microstructure Transition in Highly Undercooled Single Phase Alloys

Dendritic Solidification of Highly Undercooled Dilute Alloys

Phase-field model of isothermal solidification in multicomponent alloys for multiple grains

Concentration and Fluid Flow Effects on Kinetics, Dendrite Remelting and Stress Accumulation Upon Rapid Solidification of Deeply Undercooled Alloys

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

Uniform Droplet Spraying of Magnesium Alloys: Modeling of Apollonian Fractal Structures on Micrograph Sections

Numerical modeling and simulation of water cooling-controlled solidification for aluminum alloy investment casting

An Integrated Model for Dendritic and Planar Interface Growth and Morphological Transition in Rapid Solidification

Numerical Simulation of Dendrite Growth of Aluminum Alloy

Crystallization of high stable Zr55Al10Ni5Cu30 bulk amorphous alloy

3D Stochastic Modeling of Grain Structure for Aluminum Alloy Casting

Three Dimensional Numerical Simulation of Solidification Microstructure of Single Phase Alloy

The Solidification of Cucr Alloys under Various Cooling Rates

Substantial undercooling and rapid dendrite growth of liquid Ti-Al alloy

Cooling Crystallization of Aluminum Sulfate in Pure Water Modulated by Sodium Dodecylbenzenesulfonate

The Mechanism of Dendrite Formation in a Solid-State Transformation of High Aluminum Fe-Al Alloys

Crystallization Kinetics of Mg65Cu25Nd10 Amorphous Alloy

Uncovering Microstructure Evolution and Dynamic Softening Mechanism of Spray-Deposited AlZnMgCu Alloy Under Thermal Deformation