Abstract:The mechanical properties of Cu-Ti alloys have been characterized extensively through experimental studies. However, a detailed understanding of why the strength of Cu increases after a small fraction of Ti atoms is added to the alloy is still missing. In this work, we address this question using density functional theory (DFT) and molecular dynamics (MD) simulations with modified embedded atom method (MEAM) interatomic potentials. First, we performed calculations of uniaxial tension deformations of small bicrystalline Cu cells using DFT static simulations. We then carried out uniaxial tension deformations on much larger bicrystalline and polycrystalline Cu cells using MEAM MD simulations. In bicrystalline Cu, the inclusion of Ti increases the grain boundary separation energy and maximum tensile stress. The DFT calculations demonstrate that the increase in tensile stress can be attributed to an increase in the local charge density arising from Ti. MEAM simulations in larger bicrystalline systems have shown that increasing the Ti concentration decreases the density of stacking faults. This observation is enhanced in polycrystalline Cu, where the addition of Ti atoms, even at concentrations as low as 1.5 at.%, increases the yield strength and elastic modulus of the material compared to pure Cu. Under uniaxial tensile loading, the addition of small amounts of Ti hinders the formation of partial Shockley dislocations in the grain boundaries of Cu, leading to reduced local deformation. These results shed light on the role of Ti in determining the mechanical properties of polycrystalline Cu and will enable the engineering of grain boundaries and the inclusion of Ti to improve degradation resistance.

Crystalline to Amorphous Transition and Relative Stability of Amorphous Phase Versus Solid Solution in the Cu–Ti System Studied by Molecular Dynamics Simulations

Relative Stability of Amorphous Phase Versus Solid Solution in the Ni–Ti System Revealed by Molecular Dynamics Simulations

Molecular Dynamics Study of Stability of Solid Solutions and Amorphous Phase in the Cu-Al System

Structural Stability and Amorphization Transition in the Ni–Ti System Studied by Molecular Dynamics Simulation with an N-Body Potential

Structural phase transitions in the Cu-based Cu–V solid solutions studied by molecular dynamics simulation

Lattice Stability of Some Ni-Ti Alloy Phases Versus Their Chemical Composition and Disordering

Theoretical Investigation of Cu Influence on the Stability Characteristics of T-phase in Crossover Alloys

A Molecular Dynamics Study of an Hcp-To-Fco Martensitic Transformation and Its Crystallographic Correlation in A Ti Lattice, Upon Dissolution of Cu Atoms

Interface Stability and Solid-State Amorphization in an Immiscible Cu-Ta System

Atomistic Modeling of Solid-State Amorphization in an Immiscible Cu-Ta System

Metastable phase formation in an immiscible Cu-Ta system studied by ion-beam mixing, ab initio calculation, and molecular dynamics simulation

Impact of local structure on melt dynamics in Cu-Ti alloys: Insights from ab-initio molecular dynamics simulations

Glass Forming Region of Cu-Ti-Hf Ternary Metal System Derived from the N-Body Potential Through Molecular Dynamics Simulation

Critical Solid Solubility of the Ni-Ti System Determined by Molecular Dynamics Simulation and Ion Mixing

First-principles study of crystal structure and stability of T1 precipitates in Al-Li-Cu alloys

Role of Site-selective Doping on Melting Point of CuTi Alloys: A Classical Molecular Dynamics Simulation Study

Interfacial Reaction, Amorphization Transition, and Associated Elastic Instability Studied by Molecular Dynamics Simulations in the Ni-Ta System

Structural And Dynamical Properties Of Liquid Cu80si20 Alloy Studied Experimentally And By Ab Initio Molecular Dynamics Simulations

The liquid-solid phase transition characteristics of AgxCu(500-x) alloy particles: a molecular dynamics study

Prediction of metastable phase formation in an immiscible Cu–Cr system from interatomic potential and ab initio calculation

Modeling the effects of varying Ti concentration on the mechanical properties of Cu-Ti alloys