Abstract:In this paper, the effects of the width of the mold on the surface velocity, flow field pattern, turbulent kinetic energy distribution, and surface-level fluctuation in the mold were studied with measurement of the flow velocity near the surface of the mold at high temperature with the rod deflection method and numerical calculation with the standard k-ε model coupled with the discrete-phase model (DPM) model for automobile exposed panel production. Under the conditions of low fixed steel throughput of 2.2 ton/min, a nozzle immersion depth of 140 mm, and an argon gas flow rate of 4 L/min, as the width of the mold increases from 880 mm to 1050 mm and 1300 mm, the flow velocity near the surface of the mold decreases. The flow direction changes from the positive velocity with the mold widths of 880 mm and 1050 mm to the unstable velocity with the mold width of 1300 mm. The calculated results are in good agreement with the measured results. The turbulent kinetic energy near the submerged entry nozzle (SEN) gradually increases, and the risk of slag entrainment increases. Under the conditions of high fixed steel throughput of 3.5 ton/min, the SEN immersion depth of 160 mm, and the argon gas flow rate of 10 L/min, as the width of the mold increases from 1600 mm to 1800 mm and 2000 mm, the velocity near the mold surface decreases. The flow velocity at 1/4 of the surface of the mold is positive with the mold width of 1600 mm, while the velocities are negative with the widths of 1800 mm and 2000 mm. The calculated results are basically consistent with the measured results. The high turbulent kinetic energy area near the nozzle expands to a narrow wall, and the risk of slag entrainment is significantly increased. In both cases of low and high fixed steel throughput, the change rules of the flow field in the mold with the width are basically the same. The argon gas flow rate and the immersion depth of SEN should be adjusted reasonably to optimize the flow field in the mold with different widths under the same fixed steel throughput in the practical production.

Optimization Analysis on Gap Size of Molding for Pb-GF Composite Wire

Effect of Gap Size on Coating Extrusion of Pb-GF Composite Wire by Theoretical Calculation and Experimental Investigation

Influence of technological parameters on coating speed of Pb-GF composite 'wire

Theoretical Derivation and Experimental Verification of Optimal Gap During Extrusion of Composite Wire of Lead Coated on Glass Fiber

Determination of casting parameters of thick wall die-casting of magnesium alloy and simulation of its processing

Thickness Distributions of Mold Flux Film and Air Gap in Billet Ultra-High Speed Continuous Casting Mold Through Multiphysics Modeling

Optimized Design of Compound Wire with Low Electrical Resistivity for Metal Packaging

Extrusion process of lead-clad glass fiber composites

Optimization of Billet Tube Mold Designs for High-Speed Continuous Casting

Simulation and Optimization of Casting Technique on Upper Beam of 80MN Rapid Forging Press

Optimization of porthole extrusion die for 6063 aluminum alloy profile with thin-walled multi-cavity complex section and analysis of profile performance

THE PHYSICAL SIMULATION ON EXTRUSION PROCESS OF GLASS FIBER COMPOSITE WIRE COATED BY LEAD

Research on clad-extrusion of Pb/Cu composite wire

Optimization of Flow Field in Slab Continuous Casting Mold with Medium Width Using High Temperature Measurement and Numerical Simulation for Automobile Exposed Panel Production

Optimized Design for a Combined Die with Two Stress Rings in Cold Forging Considering Thermal-Mechanical Effects

Analysis of Longitudinal Cracking and Mold Flux Optimization in High-Speed Continuous Casting of Hyper-Peritectic Steel Thin Slabs

Optimization of squeeze casting process of gearbox cover based on FEM and Box-Behnken design

Study of workability limits of porous materials under different upsetting conditions by compressible rigid plastic finite element method

Research on Lightweight Injection Molding (CAE) and Numerical Simulation Calculate of New Energy Vehicle

Co-effect of Microstructure and Surface Constraints on Plastic Deformation in Micro- and Mesoscaled Forming Process

Effect of Mold Width on the Flow Field in a Slab Continuous-Casting Mold with High-Temperature Velocity Measurement and Numerical Simulation