Abstract:TiO2 and other semiconductor materials were found to have photocathodic protection effect for the metal coupled with these semiconductors film, as the potential of the metal shifted to a more negative value than its corrosion potential and the corrosion of the metal was prevented. TiO2 has been one of the most important semiconductors because of its good environmental friendliness and chemical stability. However, due to the wide band gap of TiO2 (3.2 eV) and the recombination of the photogenerated electron-hole (e–-h+) pairs, it can only absorb the light with the wavelength less than 380 nm, and it is hard to maintain the cathodic protection in the dark. In this paper, CdSe and other materials were applied to improve the photocathodic protection property. TiO2 nanotubes was prepared by anodization method, and CdSe was deposited on the TiO2 nanotube arrays by cyclic voltammetry method, and the optimum condition was selected from different cycles. The surface morphology and crystal phase of the composite was investigated by scanning electron microscopy (SEM), X ray diffraction (XRD) method. The photocathodic protection property of the composite material for 304 stainless steel in seawater was investigated by the electrochemical method including open circuit potential (OCP), electrochemical impedance spectroscopy (EIS) and the tafel polarization curves method. The experimental results showed that open circuit potential of 304 stainless steel decreased from -190mV to -500mV when the light was turned on, and the electrode potential slowly rises to about -250mV after the light was turned off. The composite material still could maintain the protective effect on stainless steel after the light was turned off. The work was supported by the Project of National Development and Reform Commission, the Nantong Science Project (BK2014008), and National Basic Research Program of China (2014CB643304).

Fabrication of Titania Nanotubes as Cathode Protection for Stainless Steel

TiO2 Nanotube Arrays Modified Titanium: A Stable, Scalable, and Cost-Effective Bioanode for Microbial Fuel Cells

Facile fabrication of SnO2 modified TiO2 nanorods film for efficient photocathodic protection of 304 stainless steel under simulated solar light

Photoelectrochemical Performance of SnS 2 Sensitized TiO 2 Nanotube for Protection of 304 Stainless Steel

Fabrication of Well-Aligned Tio2 Nanotube Arrays with Outstanding Light-Induced Hydrophilicity Performance

Preparation of In2s3/Agins2/Tio2 Nanotube Arrays and Enhanced Photoelectrochemical Cathodic Protection for 304 Ss Under Visible Light

Fabrication and photoelectrochemical activity of Mn/Cr co-doped titanium oxide nanostructures and their application in photocathodic protection of stainless steel

Preparation of FeS2/TiO2 nanocomposite films and study on the performance of photoelectrochemistry cathodic protection

PDA decorated spaced TiO2 nanotube array photoanode material for photocathodic protection of 304 stainless steels

Photocathodic Protection of TiO2 Composite Material on 304 Stainless Steel

Fabrication of Titanium Oxide Nanotube Arrays by Anodic Oxidation

The Photo-Induced Cathodal Protection Of 304ss With Graded Bandgap Ferrite/Tio2 Nanostructures

Covalent Organic Framework Decorated TiO2 Nanotube Arrays for Photoelectrochemical Cathodic Protection of Steel

Photogenerated cathodic protection properties of Ag/NiS/TiO2 nanocomposites

Preparation of SnIn4S8/TiO2 Nanotube Photoanode and Its Photocathodic Protection for Q235 Carbon Steel Under Visible Light

Enhanced Light Response of Titania Nanotube Arrays Sensitized with Pyrite Fes2

Effect of Co3O4/TiO2 heterojunction photoanode with enhanced photocathodic protection on 304 stainless steel under visible light

Fabrication of CdSe/ZnIn2S4 modified TiO2 nanotube composite and its application in photoelectrochemical cathodic protection

Morphology controlled synthesis of Co(OH)2/TiO2 p-n heterojunction photoelectrodes for efficient photocathodic protection of 304 stainless steel

Fabrication of TiO2 Nanotube by Electrochemical Anodization: Toward Photocatalytic Application

Fabrication of multi-layered TiO 2 /CdS@ZnS nanocomposite film for highly stable and efficient photocathodic protection of carbon steel