Abstract:In the present work, we studied the dry tribological behaviour of a 100Cr6 steel, the spherical surface of which was texturized with microindentation. The purpose of adopting a mechanical indentation technique on a non-planar surface was to simultaneously evaluate the effectiveness of adopting a fast, deformation-based technique for improving the contact tribological properties. Specifically, dimples were created using an automatic microhardness tester equipped with a Vickers indenter, setting a load of 0.5 N. Friction tests were performed at different speeds considering textured surfaces with two different void ratios (VRs). Textured and untextured surfaces were tested using a ball-on-disc tribometer. In addition, the effect of dimple size was evaluated by producing Vickers indented surfaces at a load of 5 N per each indentation, while keeping the VR values unchanged and testing the frictional properties of such surfaces at a fixed speed of 4.18 mm/s. Textured surfaces were deeply investigated to motivate the improvement of tribological properties. Notably, compared to the untextured samples, the microindented samples exhibited a much lower coefficient of friction (COF), with a friction reduction compared to the untextured case ranging from 45 to 65%, depending on the VR values. The adoption of large dimples allowed the reduction of the COF, already at smaller VR value but, in such a case, the presence of bulges at the edge of the dimple worsens the wear resistance of the counter surface. In addition to reducing the contact area and the capability to trap any debris in the dimples, the local measurement of strength allowed to clarify that the friction reduction is also determined by the work hardening effect produced by the microindentation texturing. Considering the significant improvements recorded in terms of COF and the high ability to indent even non-planar surfaces, the proposed approach can be considered very promising and, therefore, industrially applicable (e.g. using a specifically designed multi-indenter tool) to affect the friction behaviour of components, even locally, during both their use and their production.

Tribological Properties Of Surface Dimple-Textured By Pellet-Pressing

Surface Texturing for Low Friction Mechanical Components

Effect of Micro-Dimple Geometry on the Tribological Characteristics of Textured Surfaces

Effect of Micro-Dimple Texture on the Tribological Performance of Brass with Titanium Nitride (TiN) Coating under Oil-Lubricated Conditions

A Pocket-Textured Surface for Improving the Tribological Properties of Point Contact under Starved Lubrication

Friction Behavior of a Textured Surface against Several Materials under Dry and Lubricated Conditions

Tribological behaviour of microindented 100Cr6 steel surfaces in dry contact conditions

Effect of Triangular Texture on the Tribological Performance of Die Steel with Tin Coatings under Lubricated Sliding Condition

Tribological behaviors of laser textured surface under different lubrication conditions for rotary compressor

Tribological Properties of Ti6Al4V Titanium Textured Surfaces Created by Laser: Effect of Dimple Density

The Friction And Wear Behavior Of Laser Textured Surfaces In Non-Conformal Contact Under Starved Lubrication

Effect of surface texture on the frictional properties of grease lubricated spherical plain bearings under reciprocating swing conditions

Optimization of Tribological Characteristics of a Combined Pattern Textured Surface Using Taguchi Design

Effects of Laser Surface Texturing and Lubrication on the Vibrational and Tribological Performance of Sliding Contact

Surface textures fabricated by laser and ultrasonic rolling for improving tribological properties of TiAlSiN coatings

Effect of Surface Texture on the Tribological Behavior of Sliding Electrical Contact Interface

Process-surface morphology-tribological property relationships for H62 brass employing various manufacturing approaches

Topology optimization of AISI 4140 steel with surface texture filled by multi-solid lubricants for enhancing tribological properties

Simulation and Experimental Study on Tribological Properties of Herringbone Texture on 42CrMo Bearing Alloy Steel Surface

Improved tribological performance of AISI 316L stainless steel by a combined surface treatment: Surface texturing by selective laser melting and plasma nitriding

Numerical Simulation and Experimental Investigation on Tribological Properties of Gear Alloy Surface Biomimetic Texture