Abstract:The melt grafting of acrylates onto LLDPE was investigated for monomers of GMA,HPMA, HEMA, EMA, MMA and HEA by Haake mixer. It is found that, the depolymerization would occur during the melt grafting process for the grafted acrylate oligomer chains when the temperature was higher than the ceiling temperature (T-c) of the grafted acrylate polymers, which induced the decrease in the grafting ratio of the acrylates. T-c varied with different molecular structures of acrylate monomers. The influence of the steric hindrance and the special interactions between monomers was discussed. For the monomers with hydroxyl groups (GMA,HPMA, HEMA, HEA), the larger the steric hindrance is, the lower the reaction heat, which results in the lower ceiling temperature. The monomers of MMA and EMA have no hydroxyl groups, so the reaction heat is much lower, which results in the relatively low ceiling temperature than that with hydroxyl groups. The order of the ceiling temperatures was finally suggested: T-c(HEA) > T-c(HEMA) > T-c(HPMA) approximate to T-c(GMA) > T-c(EMA, MMA). The solution polymerization in dichlorobenzene of the acrylate monomers was carried out respectively and the ceiling temperature ranges of different acrylate monomers were identified, which agreed well with the results of melt grafting. The styrene (St) was added as co-monomer to assist the grafting of acrylate monomers onto LLDPE, and the effect could be predicted by the Q-e rule. The grafting ratio of GMA,HPMA,MMA and EMA could be improved by adding St because they can copolymerize with St well and the depolymerization in melt grafting could be depressed even at high temperatures.

Behaviours of Crosslinking and Grafting of EPDM in the Presence of Anhydrous Aluminum Chloride

Effects of the Competition Between Grafting Reaction and Decomposition on the Miscibility and Rheological Behaviors of PS/POE Blends in the Presence of AlCl3

Photoinitiated Crosslinking of EPDM/inorganic Filler Blends and Characterization of Related Properties

The effect of cross-linking system and reinforcement on the cross-linking reaction of peroxide vulcanized ethylene-propylene-diene terpolymer (EPDM) matrix

Mechanical Properties and Thermal Behaviors of Dynamically Photocrosslinked PP/EPDM Blends

STUDY ON SYNTHESIS OF EPDM-g-MAN AND IMPACT TOUGHNESS OF AEMS

Characterization of chemical structure and morphology of MCS graft terpolymer

Influences Of Grafting Formulations And Processing Conditions On Properties Of Silane Grafted Moisture Crosslinked Polypropylenes

Effects of Dynamic Crosslinking on Crystallization, Structure and Mechanical Property of Ethylene-Octene Elastomer/EPDM Blends

Influence of the reaction conditions on the solid-state graft copolymerization of methyl methacrylate and polyethylene/polypropylene in situ alloys

Dynamically photocrosslinking of polypropylene/EPDM blends as a thermoplastic elastomer

Influence of the Degree of Grafting on the Morphology and Mechanical Properties of Blends of Poly(butylene Terephthalate) and Glycidyl Methacrylate Grafted Poly(ethylene‐co‐propylene) (EPR)

Study on Solution Polymerization of EPDM-g-MS by Grafting Method

Melt Grafting of Vinyltrimethoxysilane and Water Crosslinking of Polypropylene/Ethylene-Propylene Diene Terpolymer Blends

Photocrosslinking of an Ethylene–propylene–diene Terpolymer and the Characterization of Its Structure and Mechanical Properties

Degradation and Thermal Properties of in Situ Compatibilized Ps/Poe Blends

EPDM/MMA-St-An Suspension Graft Copolymerization and Toughness of AEMS

Molecular Dynamics Simulations on Epoxy Resin Composite via Grafting Acryloyl-chloride to Inhibit Electron Transport and Improve Thermal-mechanical Properties

Mechanical properties and structural characteristics of dynamically photocrosslinked PP/EPDM blends

Influence Of Grafting Formulations And Extrusion Conditions On Properties Of Silane-Grafted Polypropylenes

MOLECULAR STRUCTURE EFFECT ON MELT GRAFTING OF ACRYLATES ONTO LLDPE