Abstract:It is crucial to increase the values of S BET/burn-off ratio to achieve activated carbon (AC) with a higher SO2 adsorption capacity at a low cost from flue gas. In this study, at first, Jixi bituminous coal was used as a raw material to prepare a series of pre-treated samples by oxidation treatment and adding different amounts of the FeCl3 catalyst. Then, the AC samples were prepared by pyrolysis under a N2 atmosphere and physical activation with CO2. Finally, the change in the physico-chemical structure of different samples was determined to study the effects of oxygen functional groups and FeCl3. The results show that the rapid growth of mesopores is mainly influenced by the evolution of oxygen functional groups, whereas the micropores are mainly influenced by the FeCl3 catalyst during pyrolysis. These effects can also further improve the size and the carbon type of the aromatic structure from a different perspective to promote the disordered microstructure of treated chars (1FeJXO15-800H, 3FeJXO15-800H and 6FeJXO15-800H) as compared to the ordered microstructure and less pores of the un-pretreated char (JX-800). Then, the active sites can no longer be consumed preferentially in the presence of the catalyst; this results in the continuous disordered conversion of the microstructure as compared to the ordered conversion of JX-800 char during activation. On the one hand, the developed initial pores of 1FeJXO15-800H, 3FeJXO15-800H, and 6FeJXO15-800H chars promote the favorable diffusion of activated gas, following the non-hierarchical development. On the other hand, the presence of Fe-based catalysts facilitates the etching of carbon structure and the rapid and continuous development of the micropores, hindering the severe carbon losses on the particle surface. Finally, the 3FeJXO15-800H char with a high value of S BET (1274.64 m2 g-1) at a low burn-off value (22.5%) has the highest S BET/burn-off ratio value of 56.65 m2 g-1/%, whereas the JX-800 char with a low value of S BET (564.19 m2 g-1) at a burn-off value of 58.2% has the lowest S BET/burn-off ratio value of 9.69 m2 g-1/%. Therefore, the presence of oxygen functional groups and FeCl3 has obviously changed the evolution of the physico-chemical structure in activated carbon to effectively enhance the values of S BET/burn-off.

The Effect of Activated Carbon Fiber Structure and Loaded Copper, Cobalt, Silver on the Adsorption of Dichloroethylene

Modification of Activated Carbon Fiber by Loading Metals and Its Capablity of Iodine Absorption

Hierarchical Pore Structure of Activated Carbon Fabricated by CO2/microwave for Volatile Organic Compounds Adsorption

Adsorption of Volatile Organic Compounds on Activated Carbon Fiber Prepared by Carbon Dioxide

Adsorption of Polychlorinated Dibenzo-P-dioxins/dibenzofurans on Activated Carbon from Hexane.

Poly(N,N-dimethylaminoethyl methacrylate) modification of activated carbon for copper ions removal

Effect of Metallic Oxides on Adsorption of SO2 on Activated Carbon

Influence of Transition Metals on the Pore Structure and Adsorption Properties of Spherical Activated Carbon

Effect of Char Structures Caused by Varying the Amount of Fecl3 on the Pore Development During Activation

Effect of Activated Carbon Prepared from Grapefruit Peel on the Treatment of Heavy Metal Copper

Experiment of Activated Carbon from Sludge with Different Constituent of Extracellular Polymeric Substances

Effects of Oxygen Functional Groups and FeCl3 on the Evolution of Physico-Chemical Structure in Activated Carbon Obtained from Jixi Bituminous Coal.

Effects of Carbonization and Activation Temperatures on the Characteristics of Activated Carbon-CaCl2 Composite Adsorbents

Technological Process and Mechanics of Adsorption of Heavy Metal Cadmium by Modified Activated Carbon

Preparation of Activated Carbon Microspheres from Phenolic Resin with Metal Compounds by Sub- and Supercritical Water Activation

Boosting the adsorption capacity of activated carbon prepared from Amygdalus communis shells using physicochemical co-activation method

Specific alkali metal sites as CO2 traps in activated carbon with different pore size for CO2 selective adsorption: GCMC and DFT simulations

Effect analysis of pore wall thickness, pore size, and functional group of activated carbon on adsorption behavior based on molecular simulation

Effects of Catalysts on the Pore Structure and Morphology of a Lignite Char

Loading mechanism and double-site reaction mechanism of Cu on activated carbon for enhanced oxidation of CO from flue gas

Evaluation of adsorption efficiency of activated carbon functionalized with methyl diethanolamine in carbon dioxide gas