Abstract:Statement of problem: The selective laser melting (SLM) manufacturing technique has been widely employed to produce Co-Cr dental metal frameworks. The selection of Co-Cr alloy powders has the potential to influence the microstructure and tensile properties, consequently impacting the bond strength of the metal-porcelain. However, limited information is available regarding the effect of Co-Cr alloy powder on these properties when all other factors remain consistent. Purpose: The purpose of this in vitro study was to assess how the choice of Co-Cr alloys during SLM manufacturing influences the microstructure, tensile properties, and bond strength of metal-ceramic combinations. Material and methods: Three different Co-Cr alloy powders, Co-Cr-Mo, Co-Cr-Mo-W, and Co-Cr-W were selected in this study. The powder characteristics and chemical compositions were analyzed using a scanning electron microscope (SEM) and energy dispersive X-ray (EDX) analysis, respectively. Subsequently, 12×12×15-mm cube specimens, cylindrical tensile test specimens, and 25×3×0.5-mm metal strips were fabricated using the SLM technique. Microstructural investigations of the cube specimens were conducted after metallographic preparation using SEM. The cylindrical tensile specimens (n=8) from each composition were subjected to tensile tests at a deformation rate of 0.5 mm/min. Following the application of ceramic to the metal specimens (n=10) in each group, the strength of the metal-ceramic bond was evaluated through a 3-point bend test conducted at a crosshead speed of 1 mm/min. Mechanical properties obtained from the tensile tests and bond strength values were statistically analyzed using a one-way ANOVA and Tukey post hoc comparison tests (α=.05). Results: Melt pool boundaries, columnar and equiaxed grains, and precipitates were observed in the microstructures of 3 different alloys produced by SLM. The Co-Cr-Mo-W alloy had more uniformly dispersed and finely distributed precipitates compared with other alloy compositions. The Co-Cr-Mo-W alloy had exhibited the highest yield strength (1068.0 ±41.2 MPa) and ultimate tensile strength (1263.4 ±10.7 MPa) while showing the lowest ductility under the tensile tests (6.1 ±0.9%) among all 3 alloys. Significant differences in the tensile mechanical properties were observed in the alloys except between the yield strength of the Co-Cr-Mo and Co-Cr-W alloys. The highest elongation (8.9 ±1.2%) was seen in the Co-Cr-Mo alloy. However, no significant differences were detected regarding the bond strength of all 3 groups (P>.05). The mean bond strength values were approximately 42 MPa for all the alloys. Conclusions: The results indicate that the selection of different Co-Cr alloy powders used in SLM production may influence both microstructure and tensile properties. However, the strength of the metal-ceramic bond of Co-Cr alloys remained unaffected by this selection.

Comparative study of metal-ceramic bonding strength by selective laser melting(SLM) and traditonal casting technology

[Metal-ceramic bond strength of Co-Cr alloy processed by selective laser melting]

Metal-ceramic bond strength of Co-Cr alloy fabricated by selective laser melting

[Effect of different sandblasting conditions on the metal-ceramic bonding strength of Co-Cr alloy fabricated by selective laser melting technology]

Bond strengths of porcelain to cobalt-chromium alloys made by casting, milling, and selective laser melting

Evaluation of the mechanical properties and porcelain bond strength of cobalt-chromium dental alloy fabricated by selective laser melting

EFFECT OF REPEATED FIRINGS ON METAL CERAMIC BOND STRENGTH OF CO-CR ALLOY FABRICATED BY DIRECT METAL LASER SINTERING AN IN-VITRO STUDY

Comparison of tensile properties and porcelain bond strength in metal frameworks fabricated by selective laser melting using three different Co-Cr alloy powders

Bond strength and interfacial analysis of six CoCr alloys made by conventional casting and selective laser melting

Comparative Analysis of Mechanical Properties and Metal-Ceramic Bond Strength of Co-Cr Dental Alloy Fabricated by Different Manufacturing Processes

Comparative analysis of the microstructures and mechanical properties of Co-Cr dental alloys fabricated by different methods

Adhesion of veneering porcelain to cobalt-chromium dental alloys processed with casting, milling, and additive manufacturing methods: A systematic review and meta-analysis

Metal-ceramic bond strength of a cobalt chromium alloy for dental prosthetic restorations with a porous structure using metal 3D printing

Evaluation of bond strength of porous cobalt-chromium metal and pressed ceramic fabricated by additive manufacturing

Microstructure Evolution and Mechanical Properties of Ceramic Shell Moulds for Investment Casting of Turbine Blades by Selective Laser Sintering

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Performance Study and Heat Treatment Analysis of Selective Laser Melting SiC/18Ni300 Martensitic Mold Steel Composites

A Comparable Study on Laser Welding Behaviors of Selective Laser Melted 304 Stainless Steel, Inconel 718 Superalloy and Ti-6Al-4V Alloy

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Characteristics of Metal Specimens Formed by Selective Laser Melting: A State-of-the-Art Review

Effects of post-treatment on metal-ceramic bond properties of selective laser melted Co-Cr dental alloy. Part 1: Annealing temperature