Abstract:Hydrogels are a cross-linked network of polymers swollen with liquid and have the potential to be used as a synthetic replacement for local defects in load bearing tissues such as articular cartilage. Hydrogels display viscoelastic time dependent behavior, therefore experimental analysis of stresses at the surface and within the gel is difficult to perform. A three-dimensional model of a hydrogel was developed in the commercial finite element software ABAQUS™, implementing a poro-viscoelastic constitutive model along with a contact-dependent flow state and friction conditions. Water content measurements, sliding, and indentation experiments were performed on neat polyvinyl alcohol (PVA), and on low friction boundary lubricant functionalized (BLF-PVA) hydrogels, both manufactured by freeze-thaw processes. Modulus results from the indentation experiments and coefficient of friction values from the sliding experiments were used as material property inputs to the model, while water content was used to calculate initial flow conditions. Tangential force and normal displacement data from a three-dimensional simulation of sliding were compared with the experiments. The tangential force patterns indicated important similarities with the fabricated hydrogels that included an initially high force value due to time dependent deformation followed by a decrease in a stabile value. A similar trend was observed with the normal displacement. These comparisons rendered the model suitable as a representation and were used to analyze the development and propagation of stresses in the immediate surface region. The results showed that in a three-dimensional stress field during sliding, the maximum stress shifted to the surface and rotated closer to the leading edge of contact. This occurred because the stress field becomes dominated by an amplified compressive stress at the leading edge due to the biphasic viscoelastic response of the material during sliding. Also, the complex multi-axial contact stress field was reduced to focus predominately on stress in the contact surface region in the direction of sliding. The results showed that during biphasic viscoelastic frictional sliding, the maximum tensile stress develops at the trailing edge of contact and a compressive stress develops at the leading edge in the direction of motion. The BLF-PVA hydrogels displayed a decrease in this tensile and compressive stress as compared to the standard PVA. The diminishment of these stresses would be expected to give the BLF-PVA hydrogels lower material wear with greater life expectancy as a synthetic articular cartilage implant.

The Surface Lubricative Properties of PVA/PVP Hydrogels Treated with Radiation Used As Artificial Cartilage

Facile Preparation of Irradiated Poly(Vinyl Alcohol)/Cellulose Nanofiber Hydrogels with Ultrahigh Mechanical Properties for Artificial Joint Cartilage

Mechanical and Tribological Study of PVA–pMPDSAH Double-Network Hydrogel Prepared by Ultraviolet Irradiation and Freeze–Thaw Methods for Bionic Articular Cartilage

Effects of PVA, agar contents, and irradiation doses on properties of PVA/ws-chitosan/glycerol hydrogels made by γ-irradiation followed by freeze-thawing

Preparation, mechanical properties, fatigue and tribological behavior of double crosslinked high strength hydrogel

Radiation synthesis of PVP/CMC hydrogels as wound dressing

Double-Cross-Linked Hydrogel Strengthened by UV Irradiation from a Hyperbranched PEG-Based Trifunctional Polymer

Investigation on the formation mechanisms of hydrogels made by combination of γ-ray irradiation and freeze-thawing

Investigation On The Formation Mechanisms Of Hydrogels Made By Combination Of Gamma-Ray Irradiation And Freeze-Thawing

Cationic Modified PVA Hydrogels Provide Low Friction and Excellent Mechanical Properties for Potential Cartilage and Orthopedic Applications

Double‐network polyvinyl alcohol composite hydrogel with self‐healing and low friction

Carbon quantum dots improve the mechanical behavior of polyvinyl alcohol/polyethylene glycol hydrogel

The Effects of Surface Mechanical Deformation and Bovine Serum Albumin on the Tribological Properties of Polyvinyl Alcohol Hydrogel as an Artificial Cartilage

Tribological Properties and Structure of Ultra-High Molecular Weight Polyethylene after Gamma Irradiation

Influence of Preparation Parameters on the Frictional Behavior of PVA Hydrogel Against Glass Substrate

Thermal and rheological properties of poly(vinyl alcohol) and water‐soluble chitosan hydrogels prepared by a combination of γ‐ray irradiation and freeze thawing

Modification of Frictional Properties of Hydrogel Surface via Laser Ablated Topographical Micro-Textures

Experimental and numerical tribological studies of a boundary lubricant functionalized poro-viscoelastic PVA hydrogel in normal contact and sliding

Structural Study and Preliminary Biological Evaluation on the Collagen Hydrogel Crosslinked by Γ-Irradiation.

Investigation of PVA/ws-chitosan hydrogels prepared by combined γ-irradiation and freeze-thawing

Bioinspired, Recyclable, Stretchable Hydrogel with Boundary Ultralubrication