Abstract:Diamond-like carbon (DLC) coatings have attracted much attention due to their excellent hardness, low friction, and superior corrosion resistance. Unfortunately, the poor adhesion caused by internal stress limits the typical thickness to below 3-5 mu m. This paper presents a novel interlayer design and interface engineering and the induced excellent adhesion of thick diamond-like carbon (DLC) coatings on a high speed steel substrate. The interlayer has fundamentally a graded Cr/CrCx/CrC/DLC structure, but various treatments to the hetero-interfaces have been conducted including sequential energetic ion bombardments with Cr at the substrate/Cr interface using high-power impulse magnetron sputtering (HiPIMS) and with C at the CrC/DLC interface using an anode layer ion source. It has been observed that the critical load has been improved from 18 N for a single Cr interlayer to 77 N for a Cr/CrCx/CrC interlayer for thick DLC coatings of 13 mu m. Using the same design, a very high critical load of 73 N has been achieved on the ultra-thick DLC coating of 50 mu m. This interlayer design has allowed the deposition of a DLC coating that is not only thick but also hard with excellent tribological properties. The DLC coatings have a high hardness of > 18 GPa, a low friction coefficient of 0.12 and a low wear rate of (1.7 +/- 0.2) x 10(-15) m(3)/N.m. This paper discusses the effect of the ion bombardment of the interlayer on the coating adhesion and the strengthening mechanisms. (C) 2017 Elsevier B.V. All rights reserved.

Fracture Resistance Enhancement of Diamond-Like Carbon/nitrogenated Diamond-Like Carbon Multilayer Deposited by Electron Cyclotron Resonance Microwave Plasma Chemical Vapor Deposition

Mechanical and Tribological Properties of Diamond-Like Carbon Films Deposited by Electron Cyclotron Resonance Microwave Plasma Chemical Vapor Deposition

Fracture Strength and Toughness of Chemical-Vapor-deposited Polycrystalline Diamond Films

Film Thickness Effects on Mechanical and Tribological Properties of Nitrogenated Diamond-Like Carbon Films

Structure and Mechanical Performance of Nitrogen Doped Diamond-like Carbon Films

Diamond-like Carbon Film on 20 CrNiMo Steel Prepared by Hollow-Cathode Glow Discharge

Wear-resistance of Diamond-like Carbon Thin Films Deposited on the Metal Seal Ring Surface by Plasma Gun at an Atmospheric Pressure

The properties of N-doped diamond-like carbon films prepared by helicon wave plasma chemical vapor deposition

Structural Characterization And Properties Enhancement Of Diamond-Like Carbon-Films Synthesized Under Low-Energy Ne+ Bombardment

Deposition of nano-diamond-like carbon films by an atmospheric pressure plasma gun and diagnostic by optical emission spectrum on the process

Investigation of fracture toughness and microstructure of micro-scaled multilayer-DLC/silicon system via pillar splitting method

Electrodeposition, microstructure and tribological performance of Ni/(N) incorporated diamond-like carbon films

Atomic insights on nanoindentation-induced plastic-deformation behavior of tetrahedral amorphous carbon film

Tribological Properties of Diamond-Like Carbon Films Deposited by Pulsed Laser Arc Deposition

Structural Characters and Tribological Properties of Diamondlike Carbon Films

Micromechanical properties of hydrogenated diamond-like carbon multilayers

Microstructure, wear and corrosion behavior of nano-CeO2 doped diamond-like carbon (DLC) composite films

Enhanced tribological and corrosion properties of DLC/CrN multilayer films deposited by HPPMS

Effects of sp3 bond ratio and modulation ratios on nanotribology behaviors of diamond-like carbon coatings investigated using atomistic nanoscratching simulations

Excellent Adhered Thick Diamond-Like Carbon Coatings by Optimizing Hetero-Interfaces with Sequential Highly Energetic Cr and C Ion Treatment

Multilayer Diamond‐Like Carbon Films on Monocrystalline Diamond