Sensorless Controlling for BLDCM Using One-shunt Current Detection

Li Xiaoguang,Li Yingchun,Sun Xinya,Ji Yindong

DOI: https://doi.org/10.3969/j.issn.1008-0570.2007.01.001

2007-01-01

Abstract:This paper presents a new controlling strategy for sinusoidal back EMF BLDCM and a one- shunt current detection method that simplifies current sampling. The testing results show the trustable reliability of the method.

What problem does this paper attempt to address?

A Sinusoidal Current Control Method for SPMSM Considering Uneven Demagnetization Fault

Zekai Lyu,Lijian Wu,Haolan Zhan,Yidong Du

DOI: https://doi.org/10.1109/cieec54735.2022.9846628

2022-01-01

Abstract:Irreversible demagnetization is one of the drawbacks of permanent magnet synchronous machines(PMSMs). This article first investigates the influence of uneven demagnetization fault on the current control of surface-mounted PMSMs with fractional-slot winding configurations. The characterization of permanent magnet flux linkage under rotor fault is presented by means of two-dimensional finite element analysis in a 12-slot/10-pole surface-mounted PMSM, and the mathematical model containing interharmonics is built. Then, a proportional-integral-resonant (PIR) current controller is introduced to suppress the interharmonics and reduce the undesired harmonic losses. Finally, experimental results are presented to prove the effectiveness of the proposed method.
Sensorless Control Strategy for Multiphase Induction Motor with Stator and Rotor Resistance Identification Based on Injecting Third Harmonic Current

Sheng Li,Jiaqiang Yang,Yan Wang,Guanghui Yang,Tangtang Gu,Sen qing Zhuo,Fashun Li

DOI: https://doi.org/10.1109/ciycee49808.2020.9332680

2020-01-01

Abstract:It is no longer a problem to operate an induction machine stably with sensorless control, but it is a new challenge to make induction motor system high performance without speed sensor. This paper focus on high performance sensorless control strategy with parameters identification for multiphase induction machines. This method firstly has the advantage of sensorless algorithm. Secondly, accurate rotor magnetic field orientation because of rotor resistance estimation online improves the dynamic performance of the motor and reduces the loss. Additionally, precise rotor resistance, which supplied by third harmonic plane, can increase the stability of system at low speed and negative speed. It is noted that injection of 3 rd harmonic current not only would not bring extra torque ripple, but also can increase torque density of the motor. Finally, to validate the feasibility of proposed method, simulation results by using Matlab/Simulink are shown in the paper.
A Position Sensorless Control Strategy for the BLDCM Based on a Flux-Linkage Function

Wei Chen,Zhibo Liu,Yanfei Cao,Xinmin Li,Tingna Shi,Changliang Xia

DOI: https://doi.org/10.1109/tie.2018.2842719

IF: 7.7

2019-04-01

IEEE Transactions on Industrial Electronics

Abstract:A novel sensorless control strategy for the brushless dc motor (BLDCM) is proposed in this paper. The proposed strategy is realized by employing new flux-linkage functions and can be applied to drive the sensorless BLDCM in the high-speed and low-speed ranges with highly accurate and reliable commutation. Another attractive feature is that the jumping edges of the flux-linkage functions are utilized to determine the commutation points, so there is no threshold needed as compared with other sensorless control methods. In addition, the three-phase current control method is adopted, and terminal voltages in flux-linkage function expressions can be easily obtained by calculation. By this way, the sample delay and the influence of the floating phase voltage can be eliminated, which can improve the accuracy and reliability of the sensorless control strategy. The effectiveness of the proposed strategy is verified by experimental results.

automation & control systems,engineering, electrical & electronic,instruments & instrumentation
Sensorless control of BLDC motors using an improved low-cost back EMF detection method

Zhang Lei,Xiao Wei,Qu Wenlong

DOI: https://doi.org/10.1109/PESC.2006.1712040

2006-01-01

Abstract:In this paper, an improved low-cost back EMF detection method is presented. With proper PWM strategy, the true back EMF zero-crossing point can be directly extracted by detecting voltage difference between the phase terminal and the midpoint of dc link without sensing the motor neutral voltage. No filtering circuit is required, and 100% duty ratio PWM control of BLDC motors is provided with the presented method. For only one of the three phase terminals is sensed to obtain six commutation signals which are used to perform the inverter commutation, the cost of the sensing circuit is reduced significantly; and furthermore, the imbalance in six commutation signals, which is caused by the asymmetrical behavior of three phase windings in BLDC motors, is decreased remarkably. The proposed method makes it possible to achieve good motor performance over a wide speed range and to simplify the starting procedure. The detailed circuit model is analyzed and some experimental results obtained from a sensorless prototype are shown to verify the analysis and confirm the validity of the proposed method.
Adaptive Sensorless Control of High Speed Surface-Mounted PMSM Drives with Inductance Estimator Based on Current Error

Zhihao Song,Wenxi Yao,Kevin Lee

DOI: https://doi.org/10.1109/ecce50734.2022.9947748

2022-01-01

Abstract:Due to their high power density, high efficiency and wide speed range, high speed surface-mounted permanent magnet synchronous motors (SPMSMs) with model-based sensorless field-oriented control (FOC) are evolving rapidly. The accuracy of conventional sensorless control method for SPMSM based on $d$ -axis current error mainly relies on estimated inductance. However, the actual inductance varies in a wide range with different loads, which greatly degrades the performance and narrows the application scope. Therefore, this paper proposes an inductance estimator, which utilizes both $d$ -axis and $q$ -axis current errors to construct a second-order inductance error equation. Consequently, the inductance can be estimated in an adaptive manner to improve the sensorless accuracy in various working conditions. The proposed inductance estimation method is validated on a 14krpm SPMSM, showing convergence from estimated to actual inductances at different loads even with ± 50% inductance variation. As a result, the current amplitude is reduced by more than 10% at full load, verifying the high accuracy and effectiveness of the proposed method.
Current Sampling Scheme for Finite-Control-Set Model Predictive Control of PMSM Drives with Two Shunt Resistors

Zhuoyi Chen,Liang Chen,Jianqi Qiu,Li Shi,Donglian Qi

DOI: https://doi.org/10.1109/PRECEDE57319.2023.10174466

2023-01-01

Abstract:In two-shunt-resistor-based (2-SRB) permanent magnet synchronous (PMSM) drives, the phase currents can only be measured in certain switching states, which brings difficulties in implementing the finite-control-set model predictive control (FCS-MPC) and other non-modulator-based control schemes. A current sampling scheme is proposed for the FCS-MPC of the 2-SRB PMSM drives to reconstruct the phase currents when they are not measurable. To improve the accuracy of the reconstruction and the current control, a recursive least-square regressor considering the incomplete current information is proposed to estimate all parameters in the prediction model. The experimental results on a pump PMSM verify the performance of the proposed scheme in current reconstruction and in model estimation. And the advantage in voltage utilization is also shown.
Online Sensorless Position Estimation for Switched Reluctance Motors Using One Current Sensor

Chun Gan,Jianhua Wu,Yihua Hu,Shiyou Yang,Wenping Cao,James L. Kirtley

DOI: https://doi.org/10.1109/TPEL.2015.2505706

IF: 5.967

2016-01-01

IEEE Transactions on Power Electronics

Abstract:This paper proposes an online sensorless rotor position estimation technique for switched reluctance motors (SRMs) using just one current sensor. It is achieved by first decoupling the excitation current from the bus current. Two phase-shifted pulse width modulation signals are injected into the relevant lower transistors in the asymmetrical half-bridge converter for short intervals during each cu...
Analysis and Comparison of Two Current Sensorless Servo Control Methods for Permanent Magnet Synchronous Motor

Yuhang Sun,Xiehe Lu,Zhihao Song,Wenxi Yao

DOI: https://doi.org/10.1109/ipemc-ecceasia48364.2020.9368060

2020-01-01

Abstract:The cost of motor control system can be reduced by adopting current sensorless control strategy in the application of small power servo motor, and the position control accuracy of the system can be guaranteed. Among the current sensorless control methods, the no current loop method and current estimation method are commonly used. In this paper, the principle and realization process of the two methods are introduced in detail. The performance of the two methods is compared by the open-loop bode diagram of the system, and the parameter robustness of the two methods is compared by the closed-loop zero pole map of the system. The two kinds of current sensorless servo control methods are realized by simulation based on a small power surfaced permanent magnet synchronous motor, and the results of theoretical comparison are verified. Finally, the two control methods are compared in terms of system performance and parameter robustness.
Sensorless control and start-up strategy of permanent magnet synchronous motor

Yao-zhong ZHANG,Jin HUANG,Min KANG

DOI: https://doi.org/10.15938/j.emc.2015.10.001

2015-01-01

Abstract:In order to realize sensorless vector control of permanent magnet synchronous motor, a novel method based on improved flux observer was adopted. A low-pass filter was used instead of a pure inte-grator, which reduced the errors caused by the initial value and DC offset. The magnitude and phase er-rors of the stator flux linkage introduced by the low-pass filters were compensated in the polar coordinate to make accurate estimation of speed and rotor position. In order to start motor successfully under the load conditions, a start-up method called I-f control was used, which can avoid the problem of overcurrent. A new switching strategy was also adopted. The given position was switched to the estimated according to weighting function. At the same time the given stator current was changed accordingly. It ensured that motors could switch from I-f control mode to vector control mode smoothly and reliably. The experimental results verify that the sensorless control system can work reliably and stably with smooth switching process and good control performance.
Design of Dual Mode Brushless DC Motor Controller Based on Position Sensor or Sensorless

CHEN Tie-zheng,YAN Gang-feng

DOI: https://doi.org/10.3969/j.issn.1673-6540.2011.02.008

2011-01-01

Abstract:A dual mode control method of brushless DC motor(BLDCM) either with position sensor or sensorless was presented.The controller worked with position sensor under normal condition,but it would switch to the sensorless mode automatically once the position sensor was broken down or the signal wire got disconnected.The mode tran-sition technology and sensorless rator position detecting technology were mainly discussed.Under the sensorless mode,by using short pulse test method based on the magnetic saturation effect of the stator iron and the maximum probability method,the position of the rator still or at low speed could be located.By using the back EMF zero-crossing point detecting method,the rator's position could be located at higher speed.
Independent Current Control of Dual Parallel SRM Drive Using a Public Current Sensor

Chun Gan,Jianhua Wu,Ning Wang,Yihua Hu,Wenping Cao,Shiyou Yang

DOI: https://doi.org/10.1109/tmech.2016.2592981

2016-01-01

IEEE/ASME Transactions on Mechatronics

Abstract:Switched reluctance motors (SRMs) have been considered a potential candidate for automotive applications due to its rare-earth-free feature and wide speed range. Conventionally, a current sensor is installed in each phase for the current regulation control, which will considerably add the cost and volume to multimotor drives. This paper proposes an independent current control technique for dual parallel SRM drives using only one current sensor. In order to identify the individual motor currents from the public current, a pulse injection scheme is developed accordingly. Two pulses are individually injected into the lower transistors of the dual converter in the excitation regions and the fixed current sampling points triggered by the injected pulse are presented for motor current identification. The independent current control for the dual SRM can be directly implemented by the public current sensing, although the motor parameters are different. The developed system requires only one current sensor without additional hardware or reduced system performance. The simulation and experimental results on parallel 750 W and 150 W three-phase 12/8 SRM drives are presented to confirm the effectiveness of the proposed method. With this scheme, the dual-motor drive can be more compact and cost effective for traction drive applications.
Current Sensorless Deadbeat Predictive Control Method for Permanent Magnet Synchronous Motor

Jiang Long,Ming Yang,Ying-qiang Li,Dian-Guo Xu

DOI: https://doi.org/10.1109/iecon.2017.8217436

2024-01-01

Abstract:A deadbeat predictive control based current sensorless control method is proposed as a backup method in this paper, by replacing the current feedback with the predicted current at one sampling period ahead, the feedback current information is not needed, thus current sensors can be omitted. Noticing that parameter mismatch will largely influence the control performance of predictive control, q axis inductance is identified online by recursive least square (RLS) method when the motor is functioning with healthy current sensors. Effectiveness of the proposed methods is verified through experiment on a 750W PMSM servo system and it shows that favorable speed response can be achieved.
Position Sensorless Control for PMSM Drives with Single Current Sensor

Hao Yan,Wenjie Wang,Yongxiang Xu,Jibin Zou

DOI: https://doi.org/10.1109/tie.2022.3148748

IF: 7.7

2023-01-01

IEEE Transactions on Industrial Electronics

Abstract:The aim of this article is an attempt to provide a more credible control mode or a fault-tolerant control strategy for permanent magnet synchronous motor (PMSM) drives when an unexpected failure occurs to the current or position sensor. Considering that, a position sensorless control method that uses only one current sensor is proposed. Different from a traditional position sensorless control scheme that utilizes additional current sensors to obtain information of multiple phase currents, only a single current sensor (SCS) arranged on one of the current branches is included among the whole control circuit. Three-phase currents are reconstructed by sequentially sampling the SCS under specific voltage vectors, and directly employed for motor position estimation. A nonlinear position observer established according to the gradient descent is adopted. Focusing on the special current-acquisition pattern in this article, a step-size optimization method based on golden section search is proposed to minimize position estimation error. The experimental results reveal that the method in this article is comparable to the traditional full-current-sensor method in terms of position estimation, which confirms the fault-tolerant capability as one certain sensor of the control structure malfunctions.
Speed Sensorless Model Predictive Current Control Based on Finite Position Set for PMSHM Drives

Xiaodong Sun,Teng Li,Zhen Zhu,Gang Lei,Youguang Guo,Jianguo Zhu

DOI: https://doi.org/10.1109/tte.2021.3081436

IF: 6.519

2021-12-01

IEEE Transactions on Transportation Electrification

Abstract:As an efficient control strategy, model predictive current control (MPCC) has rapid response and simple calculation. This article proposes an improved MPCC scheme for permanent-magnet synchronous hub motor (PMSHM) drives. The mentioned control scheme uses the parameter values at the last moment to obtain the back electromotive force (EMF) and utilizes the obtained back EMF to obtain the predicted current value at the next moment. In the actual application of the motor, to enhance the robustness of the control system, a sliding mode controller is used to replace the conventional proportional-integral (PI) speed loop, and a finite position phase-locked loop based on the dichotomy is added to achieve sensorless speed control and provide an accurate rotor position angle. To improve the steady-state performance, the method of duty cycle is introduced, and the null vector and the actual vector are used together in the same control cycle. The simulation and experimental results both show the effectiveness of the proposed MPCC scheme, and the steady-state performance of MPCC is greatly improved compared with traditional MPCC.

engineering, electrical & electronic,transportation science & technology
A Sensorless BLDCM Speed-adjustment System Based on DSP

王微子,冼峰峰,王敏,周顺荣

DOI: https://doi.org/10.3969/j.issn.1004-7018.2004.07.006

2004-01-01

Abstract:This paper is mainly about how to use DSP to realize the sensorless BLDCM speed-adjustment system.A new current commutation theory based on analyzing the three-phase voltages is introduced. Compared with the traditional back-EMF method, it greatly improves the control system performance and brings about a new prospect for BLDCM.
An Efficiency Optimization Method for Sensorless Control of Sinusoidal PMSM

Lü Yisong,Li Xuchun,He Ji,Wu Zhengli

DOI: https://doi.org/10.19595/j.cnki.1000-6753.tces.2010.06.003

2010-01-01

Abstract:This paper presented a novel method for the sensor-less control of sinusoidal PMSM. The idea is different from the traditional one of estimating rotor position. Using the current-based PMSM parameter vector map, it is achieved through ‘mandatory synchronization-efficiency optimization’ method. The paper introduces the achieving method and demonstrated the stability according to torque-angle curve of PMSM. The method is clearly thought-out and has low complexity, the parameters of motor are adaptable, and the hardware system is simple and easy to be achieved. Our experimental results show the feasibility of the method.
A Novel Position-Sensorless Method of BLDCM Utilizing Inductance Variation

XU Ming-you,CHEN Min-xiang,LV Lu-ying

DOI: https://doi.org/10.3969/j.issn.1004-7018.2009.08.015

2009-01-01

Abstract:Back-emf method is one of the most widely used methods among the position sensorless control techniques of brushless DC motor.However,it is hard to detect the back-emf when the motor is at still or low speed.Based on the inductance variation this paper put forward a new method to solve these problems. Simulation and experimental results were also presented to verify the analyses. Finally,suggestions were listed for further research and application.
Position Tracking Controlling System of Position Sensorless Bldcm by Using Smc

Long Bo,Cao BingGang,Jiang Hui,Zhou Hao bing,Yang Hua

DOI: https://doi.org/10.1109/mesa.2006.296976

2006-01-01

Abstract:This paper is mainly about position sensorless BLDCM tracking controlling system, which substitutes the traditional position sensorless BLDC controlling system. By the virtue of overcoming the disturbance of hall which causes the wrong actions of the controlling circuit, this method improves the stability of the whole system. In addition, as it is difficult to build the mathematical model of the system for the unbalance distribution of the rotator and magnet field, the effect of slot and parameter uncertainness. Sliding Model Control has the characteristic of good robustness and self-adapting, which is especially suitable for position sensorless BLDC controlling system. This paper provides a new method to track the back electromotive force of every phase, simulation proves to gain good result and is feasiable.
A Position Sensorless Control Strategy for PMSM Drives with Single Phase Current Sensor

Guanda Xu,Fei Xiao,Chuanqiang Lian

DOI: https://doi.org/10.1109/tte.2023.3319367

IF: 6.519

2023-01-01

IEEE Transactions on Transportation Electrification

Abstract:This article aims to provide a more credible control scheme or a fault-tolerant control strategy for permanent magnet synchronous motor (PMSM) drives without a position sensor. Considering that, a position sensorless control strategy is proposed using only one phase current sensor. First, the mathematical model of full-order sliding mode observer (FSMO) is established in the stationary reference frame. Second, the coordinate transformation and notch filter (NF) are carried out for the only measurable phase current to calculate the current error information, which is needed by the FSMO. Third, a phase-locked loop (PLL) is employed to estimate the position. The motor parameter variation effect on the position estimation is evaluated. The observer’s stability and parameter design method are analyzed through the Lyapunov theory. The proposed method utilizes a single current sensor to reconstruct the three-phase current and position signals, which improves the economy of inverters and provides the possibility of fault-tolerant control with few sensors. Compared with existing methods, it is simpler to implement and does not require changing the power unit structure. Finally, experiments have shown that the proposed method is comparable to the full-current-sensor method in terms of position estimation and control performance. Compared to the traditional method, the proposed method has higher accuracy of position estimation and better dynamic and steady-state control performance.

engineering, electrical & electronic,transportation science & technology

Sensorless Controlling for BLDCM Using One-shunt Current Detection

A Sinusoidal Current Control Method for SPMSM Considering Uneven Demagnetization Fault

Sensorless Control Strategy for Multiphase Induction Motor with Stator and Rotor Resistance Identification Based on Injecting Third Harmonic Current

A Position Sensorless Control Strategy for the BLDCM Based on a Flux-Linkage Function

Sensorless control of BLDC motors using an improved low-cost back EMF detection method

Adaptive Sensorless Control of High Speed Surface-Mounted PMSM Drives with Inductance Estimator Based on Current Error

Current Sampling Scheme for Finite-Control-Set Model Predictive Control of PMSM Drives with Two Shunt Resistors

Online Sensorless Position Estimation for Switched Reluctance Motors Using One Current Sensor

Analysis and Comparison of Two Current Sensorless Servo Control Methods for Permanent Magnet Synchronous Motor

Sensorless control and start-up strategy of permanent magnet synchronous motor

Design of Dual Mode Brushless DC Motor Controller Based on Position Sensor or Sensorless

Independent Current Control of Dual Parallel SRM Drive Using a Public Current Sensor

Current Sensorless Deadbeat Predictive Control Method for Permanent Magnet Synchronous Motor

Position Sensorless Control for PMSM Drives with Single Current Sensor

Speed Sensorless Model Predictive Current Control Based on Finite Position Set for PMSHM Drives

A Sensorless BLDCM Speed-adjustment System Based on DSP

An Efficiency Optimization Method for Sensorless Control of Sinusoidal PMSM

A Novel Position-Sensorless Method of BLDCM Utilizing Inductance Variation

Position Tracking Controlling System of Position Sensorless Bldcm by Using Smc

A Position Sensorless Control Strategy for PMSM Drives with Single Phase Current Sensor