Abstract:The purpose of this paper is to model and characterize the ultimate bending strength of laminated braided fabric reinforced composites.An experimental procedure has been carried out to measure the load–deflection relationships of laminated beams made from multilayers of diamond braided carbon fabrics and an epoxy matrix subjected to 4-point bending.Two braiding angles, i.e. 5° and 15°, with different fabric arrangements have been utilized.The failure mechanisms of the fabric laminae within the laminate were realized with the help of a resin combustion and fabric peeling technique.It was found that the failure of the beams always initialed from the top surface and that some layers including the bottom surface did not fail when the maximum lateral load was applied.This shows that the ultimate bending strength of a laminate generally does not correspond to the stress level at which the last-ply failure takes place.Thus, in addition to the maximum normal stress failure criterion incorporated with the present modeling approach, a critical deflection or curvature condition is also necessary in order that the ultimate bending failure can be identified.The overall load shared by a lamina in the laminate is two-dimensional (2D), and is determined by virtue of the classical lamination theory.However, the lamina local response within its ply system is three-dimensional (3D) due to a complicated fibrous preform contained, and is analyzed based on the bridging model.Only the individual fiber and matrix properties and the laminate geometric parameters are required, which can be easily determined/measured beforehand.Using measured beam deflection corresponding to which the ultimate bending load occurred as the additional controlling parameter, the predicted load–deflection curves up to the third-ply failure for a number of the braided carbon–epoxy laminates agree reasonably well with the experimental results.

Modelling of Inter-Laminar Toughening from Chopped Kevlar Fibers

Low-velocity Impact Damage Research on CFRPs with Kevlar-fiber Toughening

On the effect of long carbon nanotubes on mode i delamination toughness of laminated composites

The Role of Ply Angle in Interlaminar Delamination Properties of CFRP Laminates

Experimental Investigation of Low-Velocity Impact Behavior and CAI on Composite Laminates by Discrete Interleaved Toughening

3D FEM Analysis of the Interlaminar Reinforcement of Short Fibers

Experimental and numerical investigation into interlaminar toughening effect of chopped fiber-interleaved flax fiber reinforced composites

Experimental and Numerical Study on the Mode I Delamination Toughness of Z-Pinned Composite Laminates

Cellulose Nanocrystal-Polyetherimide Hybrid Nanofibrous Interleaves for Enhanced Interlaminar Fracture Toughness of Carbon Fibre/epoxy Composites

A semi-analytical model for the mode II fracture toughness of multidirectional composite laminates

Fiber Bridging Analysis of Interlaminar Short Fibers in Mode Ⅱ Delamination

Interlaminar toughening in structural carbon fiber/epoxy composites interleaved with carbon nanotube veils

Study of Synergistic and Competitive Mechanisms on Toughening Cfrp Composites with Intrinsic and Extrinsic Multiscale Interleaves

Finite Element Analyses of Face/Core Interfacial Fracture Toughness of Composite Sandwich with Reinforced Chopped Fibers

Controllable Delamination of CNT-Reinforced Carbon Fiber Films by Harnessing Mechanical and Topological Characteristics of the Composites

Effect of fiber orientation of adjacent plies on the mode I delamination fracture of carbon fiber reinforced polymer multidirectional laminates

Research on Interlayer Properties of Short Fiber Intercalated Carbon Fiber/epoxy Composites

Fracture toughness and fiber bridging mechanism for mode-I interlaminar failure of spread-tow woven composites

Modeling and Characterization of Bending Strength of Braided Fabric Reinforced Laminates

In-situ Damage Mechanism Investigation and a Prediction Model for Delamination with Fibre Bridging in Composites

A Damage Model Reflecting the Interaction Between Delamination and Intralaminar Crack for Failure Analysis of FRP Laminates