Abstract:As a processing technique to change the organization and properties of materials, heat treatment was widely used to strengthen metallic materials. This study examines the impact of varying cooling rates and heat treatment durations on the mechanical properties and microstructure of AlSi10Mg alloys produced through Selective laser melting (SLM). The heat treatment process was Solution Heat Treatment (SHT, 525 °C), and the heat treatment time includes 1 h, 2 h, and 3 h. Cooling methods consist of Refrigerant Cooling (RC), Water Cooling (WC), Air Cooling (AC), Oil Cooling (OC), and Furnace Cooling (FC). As the cooling rate decreases and the heat treatment time increases, the size of the formed Si phase particles varies from small to large, and the distribution deviates from inhomogeneous to homogeneous. In addition, the number of precipitated particles increases and then decreases. To investigate the impact of cooling rates and heat treatment time on the mechanical properties of AlSi10Mg alloys, quasi-static tensile and compression tests were performed. On the other hand, the tensile strength of the heat-treatment samples decreases while the ductility increases, and the Vickers hardness of the samples also decreases with decreasing cooling rate and increasing heat treatment time. The results of the study showed that the cooling rate and heat treatment time of the material had a greater effect on its tensile properties than on its compressive properties. The samples treated at 525 °C - 2 h - AC exhibited the highest tensile and compressive properties. Finally, the analysis of the strengthening mechanism of AlSi10Mg alloys through the presence of Si phase particles of varying sizes was conducted using transmission electron microscopy.

Microstructure and Mechanical Properties of an Al–12.7Si–0.7Mg Alloy Processed by Extrusion and Heat Treatment

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Microstructure and mechanical properties of Al−Mg−Si alloy U-shaped profile

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Microstructure Evolution and Mechanical Properties of AZ80 Mg Alloy during Annular Channel Angular Extrusion Process and Heat Treatment

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

Evolution of Microstructure and Mechanical Properties of Al-Zn-Mg-Cu Alloy by Extrusion and Heat Treatment

Correlation of Solidification Microstructure Refining Scale, Mg Composition and Heat Treatment Conditions with Mechanical Properties in Al-7Si-Mg Cast Aluminum Alloys

Microstructural evolution and mechanical properties of an ultrahigh-strength Al−Zn−Mg−Cu alloy via powder metallurgy and hot extrusion

Microstructure and mechanical properties synergistically enhanced via heat treatment modification of the as-extruded Mg-1.5Al-0.5Zn-0.2Y-0.2Ca alloy

Microstructure and properties of extruded Al–Li–Cr alloy prepared from atomised powder

Microstructure evolution, mechanical property response and strengthening mechanism induced by compositional effects in Al–6 Mg alloys

Optimization of Microstructure and Mechanical Property of a Mg-Zn-Y-Nd Alloy by Extrusion Process

Effect of heat treatment on the microstructure and mechanical properties of Al‐9Si‐0.4Mg‐0.1Cu alloy

Microstructures and mechanical properties of high strength Ti-XAl-2Fe-3Cu alloys fabricated by powder compact extrusion

Effect of cooling rates and heat treatment time on Si phase of AlSi10Mg alloy manufactured by selective laser melting: Microstructure evolution and strengthening mechanism

The Effect of Extrusion and Heat Treatment on the Microstructure and Tensile Properties of 2024 Aluminum Alloy

Effect of extrusion parameters on microstructure and mechanical properties of Mg-0.12Ca-0.08Ba alloy

Effects of Heat Treatment on Microstructure and Mechanical Properties of AlSi10Mg Fabricated by Selective Laser Melting Process

Investigation on corrosion behavior and mechanical properties of an extruded Mg-Zn-Al-Sn-Mn alloy

Microstructure and mechanical properties of Mg-Gd-Zn-Zr alloy after hot extrusion