Abstract:The surface modification of continuous fiber was conducted by the inductive coupling radio frequency cold plasma (ICP) technique. The influence of the plasma parameters, such as treatment time, discharge pressure, power, etc. on the surface chemical composition,surface morphology,surface roughness and surface free energy of continuous fiber was systematically studied by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and dynamic contact angle analysis (DCAA), respectively. Results showed that the plasma treatment introduced some polar groups such as 0 C 0 onto the continuous fiber surface, increasing the percentage of surface polar groups; the plasma etched the fiber surface obviously,enhancing the surface roughness and surface free energy and improving the wettability of the fiber distinctly. Plasma treatment conditions should be appropriate during surface modification of fibers by clod plasma. After CF was treated for 5 min,CF surface polar group was increased to a relatively higher level. However,the effect of plasma etching on CF surface is relatively slower. After CF was treated for 5 min,CF surface roughness was changed a little. However, after CF was treated for more than 15 min CF surface roughness was increased significantly. Based on the study above, the interfacial adhesion and fracture mechanism of continuous fiber reinforced soluble polyaromatic ether resin composites was also systematically analysed by interlaminar shear strength (ILSS), water absorption and scanning electron microscopy (SEM) measurements. It was found that CF reinforced poly(phthalazinone ether sulfone ketone) (PPESK) composite interfacial adhesion mechanism analysis indicats that both chemical bonding and mechanical interlocking interaction has a positive effect on composite interfacial adhesion, however, mechanical interaction has a dominant effect on composite interfacial adhesion than chemical bonding interaction. Armos aramid fiber composite interlaminar, shear strength increased from 59. 5 MPa for untreated sample to 68. 8 MPa for plasma treated for 10 min under discharge power at 200 W, with an increase of 15. 6%. The water absorption decrease of composite also indirectly showed that oxygen plasma treatment improved composite interfacial adhesion. The primary failure mode of Armos aramid or PBO/PPESK composites shifted from interface failure to matrix fracture after oxygen plasma treatment. The interfacial adhesion of Armos aramid or PBO/PPESK composites was improved by oxygen plasma treatment due to the chemical linkage and mechanical bonding between Armos aramid or PBO fibers and PPESK matrices, and the chemical linkage effect exhibits more contribution than the mechanical bonding.

Surface Modification of Polyimide Films Via Plasma Polymerization and Deposition of Allylpentafluorobenzene

Modifying wetting properties of PI Film: The impact of surface texturing and CF 4 and O 2 plasma treatment

Modification of Si(100) Surface by Plasma-Enhanced Graft Polymerization of Allylpentafluorobenzene

Surface Modification of Poly(tetrafluoroethylene) Films Via Plasma Treatment and Graft Copolymerization of Acrylic Acid

Localized Surface Hydrophilicity Tailoring of Polyimide Film for Flexible Electronics Manufacturing Using an Atmospheric Pressure Ar/H2O Microplasma Jet

Characterization of fluoropolymer films deposited by magnetron sputtering of poly(tetrafluoroethylene) and plasma polymerization of heptadecafluoro‐1‐decene (HDFD) on (100)‐oriented single‐crystal silicon substrates

Surface Modification of Aramid Fiber by Plasma Induced Vapor Phase Graft Polymerization of Acrylic Acid. I. Influence of Plasma Conditions

Surface Modification of Polyimide Films Using Unipolar Nanosecond-Pulse DBD in Atmospheric Air

Ar Plasma-induced Graft Polymerization of Acrylic Acid Onto PTFE Films

The Modification of PTFE Films Grafted Acrylic Acid with Ar Plasma

Plasma Mode Influences on the Surface Hydrophobization of Polyimide

Research On Surface Modification Of Polytetrafluoroethylene Coupled With Argon Dielectric Barrier Discharge Plasma Jet Characteristics

Deposition of Nanostructured Fluoropolymer Films on Silicon Substrates Via Plasma Polymerization of Allylpentafluorobenzene

Studies on Surface Modification of Poly(tetrafluoroethylene) Film by Remote and Direct Ar Plasma

Thermal imidization of poly(amic acid) precursors on surface-modified poly(tetrafluoroethylene) films via graft copolymerization with glycidyl methacrylate

Study On Surface Modification Of Polytetrafluoroethylene Film By Ar Remote-Plasma

Surface Modification of Polymeric Materials by Plasma Immersion Ion Implantation

Surface Modification and Adhesion Improvement of Expanded Poly(tetrafluoroethylene) Films by Plasma Graft Polymerization

Hydrophilic modification of a polyimide film surface

INTERFACIAL STUDIES OF CONTINUOUS FIBERS REINFORCED POLY(AROMATIC ETHERS) CONTAINING PHTHALAZINONE MOIETIES

Surface Modification of PET Films Using Pulsed AC Plasma Polymerisation Aimed at Preventing Protein Adsorption