Abstract:As an inevitable by-product of potable water production, drinking water treatment residue (DWTR) recycling to make ceramsite can provide both environmental and economic benefits in constructing filtration treatment system for water environment remediation. Given the varied properties of DWTR from different waterworks, this study aims to identify the key factors affecting ceramsite production from DWTR as main ingredient based on five different DWTR with using clay as the auxiliary material. The results showed that of sintering temperature (500-1000 °C), DWTR:clay ratio (5:5 to 9:1), sintering time (5-60 min), and granule diameter (5-15 mm), the sintering temperature was the key parameter. Increasing temperatures from 500 to 1000 °C gradually promoted DWTR sintering by enhancing Si and Al crystallization, which typically increased the formation of SiO2 and CaAl2Si2O8 crystals in ceramsite. Ceramsites made from different DWTR tended to have different properties, mainly resulting from varied contents of Si (20.2%-48.6%), K (0.0894%-2.39%), Fe (4.56%-14.3%), and loss on ignition (11.7%-39.5%). During ingredients preparation to produce up-to-standard ceramsite, supplying additional Si and diluting loss on ignition were necessary for all DWTR, while supplying K and diluting Fe may be required for specific DWTR, due to the potential varied DWTR compositions caused by different water production processes applied (e.g., type of flocculants). Further toxicity characteristic leaching procedure analysis indicated the increased leaching of Cu. However, DWTR based ceramsite was identified as non-hazardous material; even, sintering treatment reduced the leachability of Ba, Be, Cd, and Cr. DWTR based ceramsite also had relatively high specific surface area (22.1-50.5 m2/g) and could adsorb Cd, Cu, and Pb from solution. Overall, based on appropriate management, DWTR can be recycled as the main ingredient in the production of ceramsite for water environment remediation.

New technology of utilizing dried sludge for making ceramsite

Utilization of Dried Sludge As an Additive for Making Ceramsite

Utilization of Dried Sludge for Making Ceramsite

Ceramsite Made with Water and Wastewater Sludge and Its Characteristics Affected by SiO2 and Al2O3.

Technological Study on Sintering Ceramisite with Sewage Sludge and Sediment and Fly Ash

Ceramsite obtained from water and wastewater sludge and its characteristics affected by Fe2O3, CaO, and MgO

Preparation of high-strength ceramsite from coal gangue and printing and dyeing sludge: Design strategy and modelling mechanism

Preparation of ceramsite using solid residue from anaerobic digestion of waste activated sludge and its enhancing effect on catalytic ozonation

Influence of Ceramsite with Assembly Unit of Sludge and Excavated Soil on the Properties of Cement Concrete

The Technical Study on the Preparation of Lightweight Ceramsite Made from Sewage Sludge and Fly Ash

Preparation of Lightweight Ceramsite from Solid Waste Using SiC as a Foaming Agent

The Influence of sintering temperature on sludge ceramsite

Effect of additives on the properties of ceramsite from solid wastes

Preparation of ultra-lightweight ceramsite from waste materials: Using phosphate tailings as pore-forming agent

Ceramsite obtained from water and wastewater sludge and its characteristics affected by (Fe2O3 + CaO + MgO)/(SiO2 + Al2O3)

A Study on Ceramsite Production Using Dredging Sea Mud and Its Biofilm Formation Capacity Evaluation

Ceramsite production using water treatment residue as main ingredient: The key affecting factors identification

Process and property optimization of ceramsite preparation by Bayan Obo tailings and blast furnace slag

Effect of Sewage Sludge Addition on Microstructure and Mechanical Properties of Kaolin-Sewage Sludge Ceramic Bricks

Preparation and Properties of Porous Ceramsite from Waste Foundry Sand and Ash

Effect of sintering temperature on the characteristics of sludge ceramsite