Abstract:Machine learning-based optimization analysis is conducted to improve the performance and reliability of non-metallic seals that undergo dynamic loading. Non-metallic seals, mostly made from elastomeric materials such as rubber, are widely used in the oil and gas industry due to their combination of hyper-elastic behavior and lack of plastic deformation under pressure and temperature cycles. However, these elastomeric materials could soften at elevated temperatures or during cyclic loading which makes them more prone to extrude from the seal region. For simple seals such as O-rings, thermoplastic anti-extrusion backup rings can be used to resist rubber extrusion. For more complex molded or bonded seals subject to cyclic loads and temperature cycles, minimizing the rubber damage and maintaining the seal integrity becomes more challenging as there may be inadequate room for backup rings. Additionally, the rubber may also experience repeated long stroke lengths during service which can cause surface abrasion. Non-metallic seals are extensively used in Sand Control Tools, a class of completion equipment. In the development of these molded and bonded seals, advanced optimization analysis techniques are important to make the seal design sufficiently robust to meet the stringent requirements of industry codes and regulations. Machine learning-based optimization analysis allows for increasing the seal performance and reliability. The Mullins effect is included in the elastomeric material model to capture the material softening effects under cyclic loading. Machine learning-based optimization starts with a feasible design space that is defined based on the controlling design parameters related to the geometry of the seal. Comprehensive Finite Element Analysis is performed on each design sample under the target cyclic load and temperature cycles. The key response parameters of the non-metallic seal are selected as the principal strain and the contact stress in the rubber which together indicate the damage and seal-ability states of the design. A Performance Objective Index is defined as a function of the key response parameters. The FEA results covering the entire design space provide the simulation-driven training data to build the surrogate model using multi-layer neural networks. The optimum design solution is found from the surrogate model which correlates the Performance Objective Index to the design parameters. The results of this study reveal that the performance of the seal is greatly affected by the ratio of the elastomeric seal volume to the gland volume into which the seal is molded. As opposed to the base design, the optimum design shows a solid performance with no signs of extrusion when the principal strain of the rubber is kept below the elongation limit throughout the load cycles, and when sufficient contact stress is developed to maintain the seal.

Computer-Aided Optimization of the Extrusion Process of Automobile Rubber Seal

Quick Profile Die Balancing of Automotive Rubber Seal Extrusion by CAE Technology

Analysis of Structures of the Extrusion Die of Sealing Strip of EPDM Rubber and Test Validaty

The Application of CAE Technique in the Design of Automotive Weatherstrip Seals

Numerical Analysis and Improving Design of Car Door Weatherstrip Seal

Forward extrusion simulation and invert die design of ethylene-propylene-diene rubber in simple dies

Optimized Design Method for Profile Extrusion Die Based on NURBS Modeling

Finite Element Analysis of Reciprocating Sealing Component of Radial Single-piston Pump

Cross Section Shape Optimization Design of Fabric Rubber Seal

Machine Learning Aided Optimization of Non-Metallic Seals in Downhole Tools

Finite element simulation on tire rubber extrusion process

Improved Optimization of a Coextrusion Die with a Complex Geometry Using the Coupling Inverse Design Method

Analysis and structure optimization on buckling destabilization and wrinkling of an automobile weather-strip seal in assemblage

Computer-aided design and optimization of profile extrusion dies for thermoplastics and rubber: a review

FE Simulation of Extrusion to Produce a Thin-Walled Wide Profile Through a Spreading Pocket Die

Optimization of Extrusion Part Based on Moving Least Squares Response Surface Methodology

Optimization of Die Design for Thin-Walled Flat Multi-Port Tube with the Aid of Finite Element Simulation

Optimization of porthole extrusion die for 6063 aluminum alloy profile with thin-walled multi-cavity complex section and analysis of profile performance

Optimization of thin-walled sealing structure based on mechanical simulation

3D Modeling in Injection Molding Seat and Optimization of Its Process Parameters

Numerical analysis of molding process for roll imprinting based on ABAQUS