Abstract:Amphiphilic azo polymers with different azo chromophores and degree of functionalization (DF) were synthesized, and colloidal spheres of the polymers were prepared by gradual hydrophobic aggregation in selective solvents. To obtain suspensions of colloidal spheres, the required amounts of water were added into the THF solutions at a certain stirring rate. As the water content reached ca. 70 vol%, an excess of water was added into the suspensions to "quench" the formed structures. The obtained suspensions of colloidal spheres were sealed after THF was completely volatilized and were characterized by DLS and UV-Vis spectroscopy. The size and size-distribution of colloidal spheres were measured by using a DLS/SLS-5022F laser light scattering apparatus. Before the measurement, the sample was clarified by a 0.45 mu m Millipore filter to remove dust, and all the DLS measurements were carried out with 90 degrees scattering angle. UV-Vis spectroscopy was used to study the azo chromophore structure variation in the colloid formation process by measuring the parameters such as the trans-to-cis photoisomerization rate and the isomerization degree at the photostationary state. In the photoresponse experiments, the sample was irradiated by a 365 nm UV light source, and the light intensity was 7000 mV/cm(2) at a distance of 38 cm and 21000 mV/cm(2) at a distance of 5 cm. respectively. In our experiment. the sample was 15 cm away from the UV light, and the temperature of the environment was 30 degrees C. The influences of molecular structure and preparation conditions on the size and photoresponsive properties of the colloidal spheres were studied in some detail. The result shows that the functional group type and DF as well as the preparation conditions (initial polymer concentration, the rate of water addition, etc.) have significant effects on the size and photoresponsive properties of the colloidal spheres. The size of colloidal spheres increases with the increase of DF and initial concentration, but decreases with the increase of the rate of water addition. The photoinduced isomerization rate of poly {2-[4-(4-ethoxyphenylazo)phenoxy] ethyl acrylate-co-acrylic acid} (PEAPE) colloids is higher than that of poly {2-[4-(4-cyanophenylazo) phenoxyl ethyl acrylate-co-acrylic acid} (PCNPE) colloids. The PEAPE colloids with higher DF show a slower photoisomerization rate. The photoinduced isomerization rate of the colloids decreases with the increase of initial concentration and the decrease of the rate of water addition. The possible mechanism for the influence is also discussed based on thermodynamics and kinetics consideration. It is believed that the colloidal spheres form through a self-assembling process controlled by the dynamic conditions. For high initial concentration and slow water dropping rate, more polymer chains tend to aggregate on the compact cores formed from the most hydrophobic chains as the water content is above the critical water content (CWC). Moreover, the polymeric chains had chance to rearrange themselves to form stable and compact structures due to the slow rate of water addition. On the other hand, as the rate of water addition increased I the polymeric chains attached to the cores were quickly "frozen" before they could completely adjust their conformations. Also, they could form new less compact cores so as to weaken the continuous aggregation probability. As a result, the formed aggregates had loose structures, and the photoinduced isomerization rate was relatively fast.

Optical Behavior of Organic Pigments in Aqueous Dispersions and Its Application

Preparation and colloidal dispersion behaviors of silica sol doped with organic pigment

Preparation and characterization of organic pigments and their fluorescence properties depending on bulk structure

Density functional theory/time-dependent density functional theory investigations on the color-structure relationship of biopigment molecules

The Optical Properties of Nanoparticle Dispersions Prepared by a High Speed Thin Film Mixer

Effect of bead mill dispermat system with specific surfactants on organic pigments

Size Dispersion of the Filler Particles and Its Consequences on the Light-Extinction Properties of TiO 2 /PET Nanocomposite Fibers

Erasure Effect Of The Reading Beam On The Decay Process Of Chi((2)) In All-Optical Poling

Evaluation on the Performance of Liquid Whitening Pigment for Paper

The Effects of Particle Size and Distribution of Disperse Dye on the Dyeing Performance of PLA Blended Fabric

Modification of C.I. Pigment Red 146 with surfactants and graphene oxide

Effect of particle size, transparency and light intensity on the color of powder

Milling Processing, Morphology, and Optical Characterization of Powders from Natural Pigments as a Potential Sensitizing Material for Optical Sensors and Dye-Sensitized Solar Cells

Measurement Of The Behaviors Of Optoelectron In The Photosensitive Material By The Dielectric Spectrum Technology

Effect Of Organic Nano-Pigments On Contrast Ratio Of Color Filters

Study of Sedimentation Process for Titania Pigment and Polyacrylic Dispersant Water-Borne System

INFLUENCES OF STRUCTURE AND PREPARATION CONDITIONS ON SIZE AND PHOTORESPONSIVE PROPERTIES OF AMPHIPHILIC AZO POLYMER COLLOIDAL SPHERES

Preparation of Organic Pigment Microcapsules and Its Application in Pigment Printing of Silk Fabric

Xerographic property, optical absorption, and X-Ray diffraction study of azo/TiOPc composites

<title>Measurement of the behaviors of optoelectron in the photosensitive material by the dielectric spectrum technology</title>

Research on Formula of Cyan UV Inkjet Ink