Abstract:The cuttlefish have higher swimming speed and more maneuverability than most of the fish mainly benefiting from their unique jet propulsion mechanism, which is realized by the contraction and expansion of their flexible mantle. However it is difficult to mimic this jet propulsion mechanism using conventional electro-mechanical structures. In this paper, the musculature of the cuttlefish mantle and how the mantle flexibly contracts and expands were analyzed first. Then the Shape Memory Alloy(SMA) wires were chosen as the actuators and the soft silica gel was chosen as the body materials to develop a biomimetic mantle jet propeller. The SMA wires were embedded within the soft silica gel formed with cuttlefish mantle shape along the annular direction to mimic the circular muscles of cuttlefish mantle. The water was squeezed out the mantle cavity to form rear jets when the biomimetic mantle was contracted by SMA wires. A mechanical model and a thermal model were established to analyze the jet thrust and the jetting frequency. Theoretical analysis shows that the jet thrust is proportional to the square of the rate of change of SMA strain. Increasing the driving voltage can improve the rate of change of SMA strain, thus can improve both the jet thrust and the jetting frequency. However the jetting frequency is mainly restricted by the cooling of SMA wires. To maximize the jetting frequency, the optimal driving parameters for different driving voltage were calculated. The propulsion performance was tested and the results show that the jet thrust can increase with the driving voltage as predicted and the maximum average jet thrust is 0.14 N when the driving voltage is 25 V. The swimming test was carried out to verify the feasibility of the novel design. It is shown that the biomimetic jet propeller can swim with higher speed as the jet thrust and jetting frequency increase and the maximum speed can reach 8.76 cm·s −1 (0.35 BL·s −1 ) at a jetting frequency of 0.83 Hz.

Initial Prototype Design and Investigation of an Undulating Body by SMA.

Kinematic Modelling and Hydrodynamic Analysis of Biomimetic Pectoral Fins of Cownose Ray

Design and Implementation of Multi-Level Linkage Mechanism Bionic Pectoral Fin for Manta Ray Robot

Overall Design and Flutter Motion Analysis of a Semi-active Manta Ray Robot

Design and analysis of a shape memory alloy buoyancy actuator

Design of a Shape-Memory-Alloy-Based Carangiform Robotic Fishtail with Improved Forward Thrust

Study on the Hydrodynamics and Kinematics of a Biomimetic Fin Propulsor Actuated by SMA Wires

Research on the Hydrodynamics of A Horizontal Trigonal Pectoral Fin Propulsor Actuated by Sma Wires

Computational Research on Modular Undulating Fin for Biorobotic Underwater Propulsor

Design and Locomotion Control of a Myliobatid-inspired Robot Actuated by Passively-flexing Pectoral Fins

A Biomimetic Squid Funnel Actuated by Shape Memory Alloy Wires

Design and testing of a shape memory alloy buoyancy engine for unmanned underwater vehicles

Design, Fabrication and Morphing Mechanism of Soft Fins and Arms of a Squid-like Aquatic-aerial Vehicle with Morphology Tradeoff

Prototype Design of a Kind of Biomimetic Cuttlefish Underwater Robot Actuated by SMA Wires

Bionic Propulsion:The Fluid Structure of Two Fish-tail Models in C-starts

A Prototype of a Biomimetic Mantle Jet Propeller Inspired by Cuttlefish Actuated by SMA Wires and a Theoretical Model for Its Jet Thrust

Fluid-structure investigation of a squid-inspired swimmer

Experimental and analytical study on factors influencing biomimetic undulating fin propulsion performance based on orthogonal experimental design

Research on Biomimetic Fish Fin Driven by NiTi Shape Memory Alloy

Initial Computational Research On An Undulating-Finned Robotic Fish

Design and Mechanical Property of a Biomimetic Pulsatile Jet Propeller Inspired by Cuttlefish Actuated by SMA Wires