File transmission between two PCs based on USB and MCU

FU Jia,FANG Yong,LIU Jia-yong,XIAO Yuan-jun

DOI: https://doi.org/10.3969/j.issn.1671-1742.2005.06.022

2005-01-01

Abstract:A scheme of the data transmission by the combination of P89V51RD2 mcu and USB interface device PDIUSBD12 is introduced.The frame of the principle and the realization of the software design is presented.

What problem does this paper attempt to address?

Real-time Bidirectional Data Transmission Based on USB Interface

Kuang Wang

2005-01-01

Abstract:The article designs a real-time bidirectional transmission channel.And it introduces the theory of the design,selects specific chip,introduces the hardware of the channel,and brings forward the method of designing USB firmware,driver,and application.
Research on USB Data Transmission Technology Based on LabVIEW

程龙飞,何闻

DOI: https://doi.org/10.3969/j.issn.1001-3881.2009.07.036

2009-01-01

Abstract:The USB data transmission technology based on LabVIEW was studied.The USB interface circuit which core chip is PDIUSBD12 produced by PHILIPS,the firmware programming method of the USB interface circuit,and the specific method of compiling application which is based on the LabVIEW were introduced.The result in the data transmission test shows that it can realize the data transmission between superior monitor and inferior computer by using LabVIEW and USB interface.
A Novel Physical-Layer Transceiver Used in USB2.0 Serial Data Link

Li Haoliang,He Lenian,Wang Zi,Yan Xiaolang

DOI: https://doi.org/10.1007/s11767-004-0246-4

2006-01-01

Abstract:The paper proposes a novel transceiver in physical layer for high-speed serial data link based upon Universal Serial Bus (USB) 2.0, comprising transmitter and receiver. In the design, transmitter contains pre-and-main driver to satisfy slew rate of output data, receiver includes optimized topology to improve precision of received data. The circuit simulation is based on Cadence’s spectre software and Taiwan Semiconductor Manufacture Corporation’s library of 0.25μm mixed-signal Complementary Metal-Oxide Semiconductor (CMOS) model. The front and post-simulation results reveal that the transceiver designed can transmit and receive high-speed data in 480Mbps, which is in agreement with USB2.0 specification. The chip of physical-layer transceiver has been designed and implemented with 0.25μm standard CMOS technology.
Design and Realization of Wireless File Transmission System Based on USB2.0

安国娇,王代华,张志杰

DOI: https://doi.org/10.3969/j.issn.1674-6236.2010.03.035

2010-01-01

Abstract:In order to safely and conveniently transfer files without network,the paper designed a wireless file transmission system which consisted of MCU PIC18F4550 with USB2.0 interface and high-speed wireless transceiver chip nRF24L01,it introduced from hardware and software,and elaborated on USB communication between MCU and computer,and communication process of MCU and RF chip.Experiments prove that the system can transfer different size and different format files,and the speed is up to 1.28Mb/s.The design has advantages of simple circuit,high data transmission rate,steady performance and very easy handling.
Design of Data Unilateral Transmission Based on USB 2.0

XIAO Yuan-jun,FANG Yong,ZHOU An-min,LIU Jia-yong,FU Jia

2006-01-01

Abstract:When transferring files between the different security domain,files are required to be only transferred from low security domain to high security domain.An unilateral transferring system was developed based on USB2.0 bus.Its data transmission scheme by combining USB2.0 interface device CY7C68013 and DAUL-PORT RAM was described.Experiment results verify that the system based on USB2.0 interface,DAUL-PORT RAM data buffer and technology of optical couplers insulation realizes high-speed,unilateral and reliable data transmission.
Design and Implementation of Data Uni-directional Transmission System Based on EZ-USB FX2

LI Bo,LIU Jia-yong,JIANG Yu,LIU Xian-kui

DOI: https://doi.org/10.3969/j.issn.1672-2892.2008.01.011

2008-01-01

Abstract:To satisfy the application requirements for host-computers uni-directional data trans- mission in different security ratings, a design scheme of uni-directional transmission system based on EZ-USB FX2 is presented in this paper. And the system which adopts the Universal Serial Bus(USB)2.0 chip Cy7c68013 and IDT72v06 First in First out(FIFO) memory, realizes uni-directional, high-speed, safe and reliable data transmission between the host-computers in different security domains, with hardware design of external FIFO through General Programmable Interface(GPIF) and application program.
File Transfer Based on Zigbee Technology

ZHU Wenju,YANG Yintang

DOI: https://doi.org/10.3969/j.issn.1004-373x.2007.19.006

2007-01-01

Abstract:In order to make the cost and power consumption of short distant wireless communication technology much less,the paper takes advantage of Zigbee technology whose characteristics are low-cost and low-power,brings forward a file transfer technology based on Zigbee and realizes files-transmitting among several PCs.It centers on embedded processor and RF emitting chips,with the help of peripheral hardware ports to realize the communication with terminal unit.It works well through several testing.Besides,it can fulfill the situation when the transmit amount is not so large and the cost is much smaller.
Design and Implementation of Infrared Data Transmission System Based on USB 2.0

张君怡,王海明,裴东兴

DOI: https://doi.org/10.3969/j.issn.1674-6236.2009.12.018

2009-01-01

Abstract:In order to overcome the deficiency or defect of wire transmission and avoid damaging the measurement equipment because of frequent pluging and drawing,the infrared data transmission system based on USB2.0 are designed in the paper.The overall structure and design and implementation of key hardware are described in detail,and the design of firmware,driver program and application program are also expatiated.It utilizes USB2.0 technology and infrared transmission technology to realize the wireless data transmit between measurement equipment and PC.
Design of Data Transmission System Based on FPGA and USB 2.0

Junsheng Wu,Fuzhou Shang,He Sun,Tian Qin,Qing Li

DOI: https://doi.org/10.4028/www.scientific.net/amm.321-324.417

2013-01-01

Applied Mechanics and Materials

Abstract:In this paper, a high-speed data transmission system based on FPGA (Field Programmable Gate Array) and USB 2.0 (Universal Serial Bus) technology is designed. Firstly, we introduce the hardware of the data transmission system, which includes data acquisition circuit, transmission circuit and power conversion circuit, etc. Secondly, the corresponding software design including USB firmware program, USB driver and firmware modification are described in detail. Finally, the corresponding experiment has been carried out, which show that the developed system will help to achieve the data transmission system with the characteristics of high-speed, integration and low power consumption, etc.
USB Communication Interface Design Based on the PDIUSBD11

J. Xu,Ming Tang

DOI: https://doi.org/10.4028/www.scientific.net/AMM.268-270.1570

2012-12-01

Abstract:Based on the widely used USB communication technology, when the speed requirement is not too high using USB controller chip with I2C bus develops USB interface, you can reduce the use of pin microcontroller ATmega8, simplify connection circuit. This article describes the design method of a Philips company with I2C interface USB interface chip PDIUSBD11, as well as the peripheral hardware circuit connection and USB HID class program design method. The test results show that can reliably achieve communication function between USB and computer, and has good application value.

Computer Science,Engineering
Design and Realization of MPC860's USB communication interface

Kang Hua,Zhang Xiaobin

2007-01-01

Abstract:Being an embedded communication processor which has formidable function,MPC860 not supporting USB will limits its application in some domain.So a method based on FT245BM to realize the MPC860's USB communicationg interface is been raised.There are two means to connect processor with FT245BM,one through the I/O ports of processor and the other though coding of CPLD.Because the I/O port of MPC860 are multiplexing,this method wastes the I/O port resource;Yet the CPLD coding will increase the cost and complexity of the product.S o The control logic sequences needed by FT245BM are realized through microinstruction programming in the MPC860 memory controller UPMA.The hardware and software design are describe in detail.And the method through VCP(Virtual COM Port)driver provided by FTDI to programme communication software on the PC is show as well.The testing prove the communication is stable and reliable,and the purpose to realize the USB interface on MPC860 is reached.
High Speed Transmission System Based on USB Interface Multi Bit Data Format

ZHANG Jinpeng,ZHAO Jianjun,TANG Haifeng,ZHAO En

DOI: https://doi.org/10.3969/j.issn.1672-9722.2017.12.026

2017-01-01

Abstract:This design realizes a data transmission system based on USB2.0 interface.The system from the FPGA to produce a 35-bit added to 250 from 0 of the counter,to achieve the value of the counter through the USB to the host computer's function.The design of the FPGA chip uses Altera's CycloneII EP2C5Q208C8N,USB chip Cypress's EZ-USB series CY7C68013A.Through the Quartus II software,Keil software,Cypress console for USB interface design of multi-bit data transmission system.The system can be used for high-precision,high-speed,low-cost bulk data transmission.
Design of USB Control System Based on CY7C68013A

赵铁军

DOI: https://doi.org/10.3969/j.issn.1004-373x.2010.13.060

2010-01-01

Abstract:With the increasing development of the communication technology,the universal serial bus(USB) as a new interface technology that makes the connection of PCs with peripheral equipments very simple has been extensively adopted.The feature of USB2.0 is introduced firstly,and then the overall plan for designing the control system by using CY7C68013A is presented.The function of the system firmware and the design of drive program are discussed in detail.The key issues which should be taken more attention during the system design are proposed.The control system firmware is programmed with C language.The control interface on PC is developed under the VC++6.0 development environment.The experiment indicates that the whole system runs perfectly well.
Communication through USB between PC and industrial control system

Li-ping ZHOU,Jie LI,Wen-gen ZHANG,Feng-qi DING

DOI: https://doi.org/10.3969/j.issn.1006-6047.2005.09.018

2005-01-01

Abstract:The serial port is normally used in the communication between PC and industrial control system.Due to the high performances of USB(Universal Serial Bus),a data acquisition system based on USB is designed.It consists of enhanced P89C61X2(single-chip computer),SJA1000(CAN controller) and ISP1581(USB2.0 interface chip).The industrial control system is based on FCS of CAN bus.The design and implementation of communication between PC and industrial control system through USB is expounded.The results show that it is practical to real-timely acquire and process the data and information from CAN through UBS communication.
Design and Realization of USB Interface Based on Series EZ-USB

XIE Wei-bang,WU Xiao-ming

DOI: https://doi.org/10.3969/j.issn.1003-8868.2011.03.001

2011-01-01

Abstract:Objective To design a high-speed USB interface which is used in community-oriented health care system.Methods To realize the high-speed data transmission between PC and monitoring system,the authors take good advantage of the EZ-USB-FX2 supplied by Cypress Company.After the brief description of CY7C68013a,it clarified the methods to design a high-speed USB interface by using CY7C68013a.The procedure includes hardware design,firmware development,driver production and PC program development.Results USB interface based on EZ-USB-FX2 was designed.A high-speed USB interface which was used in community-oriented health care system was supplied.Low cost and facilitation of the community-oriented health care system was realized.Conclusion The interface is convenient to be used in community-oriented health care system.
Wireless Temperature and Humility Monitoring System Based on USB Interface

王军,何鹏举,杨杰

DOI: https://doi.org/10.3969/j.issn.1002-1841.2009.12.017

2009-01-01

Abstract:To meet the requirement of temperature and humility collecting,a point-to-multipoint wireless temperature and humidity monitoring network was designed,which belonged to star network architecture.It took the wireless communication module nRF401 as the foundation,the client machine combined AT89C2051 MCU with the digital humiture sensor SHT11,and the server machine was constructed using the P89C51RD2BN MCU and USB interface chip PDIUSBD12.This paper introduced the system's hardware schematics and the humiture data acquisition methods,and a more detailed analysis of wireless communication protocol and USB firmware design method.Be tested of upper computer software,the system runs stably and has good usability,which may be applied in many kinds of wireless humiture monitoring.
Based on CH375 Transmit Data to USB

WEI Jing-bin,LIU Jun-feng,QIAN Ji,CHEN Qi-lin

DOI: https://doi.org/10.3969/j.issn.2095-6835.2010.02.063

2010-01-01

Abstract:In this article, a lot of monitoring, measurement and control systems can not be easy to transfer data to mobile devices. Here introduced a USB interface chip QinHeng CH375 and MCS51 MCU as the core, U disk and mobile hard disk storage medium as the data storage programs. The module gives the hardware circuit design and U disk reading and writing program, and points out the error-prone debugging details. The result of the experiment shows that this method with low cost, high reliability, high universality, can be easily integrated into a variety of monitoring, measurement and control system.
USB high-speed and incessant data transmission firmware programming technology

Luo Hao,Tian Shulin,Li Li

DOI: https://doi.org/10.3969/j.issn.1002-7300.2011.08.023

2011-01-01

Abstract:About the data transmission of USB,the most concerned is the efficiency and reliability of data.In practical application,how to efficiently and incessantly transmit the data is very important.Because of the different starting points of concerning issues,there are many methods of the high-speed and incessant data transmission.The firmware programming problems of USB high-speed and incessant data transmission were researched by using the ping-pang data transfer mode in the firmware programming to achieve the high-speed and incessant data transmission.The test showed that the efficiency of data transmission could be improved by this method and a large number of incessant data transmission could be achieved,which increased the reliability and continuity of data transmission.
Design for USB interface of data acquisition system based on EZ-USB FX2

王东,李公平,潘小东,方登富

DOI: https://doi.org/10.3969/j.issn.1004-373X.2015.04.020

2015-01-01

Abstract:Taking EZ?USB FX2 interface chip as an example,several aspects involved with USB interface design of indus?trial CT data acquisition system are introduced in detail in this paper. In this design,Slave FIFO is used in EZ?USB chip to im?prove the speed of data transmission. In this way, the USB kernel is not involved in the data transmission. Inside the CY7C68013A chip,4 kB configurable endpoint buffer is contained. It is the large capacity data transmission terminal,which can be configured to fulfill high?speed data transmission with peripheral circuit,but does not need 8051 firmware program to join with. The basic framework is contained in the EZ?USB firmware program development kit provided by CYPRESS company. In this paper,the structure and characteristics of the CY7C68013A chip are introduced,the EZ?USB FX2 firmware frame is ana?lyzed,the firmware example code is given,the firmware code loading way is described,and the interface between application program and driver is illustrated. With USB interface developed by means of EZ?USB chip,the development difficulty was great?ly reduced,and the development efficiency was improved.
Design of Data Transmission in Home Health Care Based on USB

WANG Wei-xia,HUANG Yue-shan,WU Xiao-ming

DOI: https://doi.org/10.7687/J.ISSN.1003-8868.2013.02.012

2013-01-01

Abstract:Objective To solve the slow transmission speed of CC2430 with serial port in home health care in order to send the collected physiological information from local computer to the remote server for remote diagnosis or health services.Methods USB interface was switched to realize the communications between CC2430 and local computer.Socket network programming technology was used to send the collected physiological information from the local computer to the remote server with Visual C++6.0 as software platform.Results The low transmission speed of serial port in home health care was solved,and the real-time transmission and display of physical information were realized.The network communication between local computer and the remote server was implemented.Conclusion The whole data transmission process of home health care is designed and completed,which has a certain reference value for the development of home health care.The design of the USB interface can be used in many other fields.

File transmission between two PCs based on USB and MCU

Real-time Bidirectional Data Transmission Based on USB Interface

Research on USB Data Transmission Technology Based on LabVIEW

A Novel Physical-Layer Transceiver Used in USB2.0 Serial Data Link

Design and Realization of Wireless File Transmission System Based on USB2.0

Design of Data Unilateral Transmission Based on USB 2.0

Design and Implementation of Data Uni-directional Transmission System Based on EZ-USB FX2

File Transfer Based on Zigbee Technology

Design and Implementation of Infrared Data Transmission System Based on USB 2.0

Design of Data Transmission System Based on FPGA and USB 2.0

USB Communication Interface Design Based on the PDIUSBD11

Design and Realization of MPC860's USB communication interface

High Speed Transmission System Based on USB Interface Multi Bit Data Format

Design of USB Control System Based on CY7C68013A

Communication through USB between PC and industrial control system

Design and Realization of USB Interface Based on Series EZ-USB

Wireless Temperature and Humility Monitoring System Based on USB Interface

Based on CH375 Transmit Data to USB

USB high-speed and incessant data transmission firmware programming technology

Design for USB interface of data acquisition system based on EZ-USB FX2

Design of Data Transmission in Home Health Care Based on USB