Abstract:Hollow fiber membranes fabricated via dry/wet phase inversion method usually have two dense skin layers,which will increase its resistance of mass transport as a support membrane. It is necessary that the dense skin layer of support membrane has been eliminated to improve separation performance of composite membrane. The excellent. chemical resistance of poly(vinylidene fluoride) (PVDF) to many acids and alkalis has made it as an attractive membrane material, and then it's often fabricated as porous hollow fiber membrane by phase inversion. In the process, the formation of the skin layer is due to the rapid exchange between solvent and coagulation, so many attempts have been made to slow it, so as to control the formation of the skin layer. In this paper, it has been found that the fabrication progress becomes unstable, and the membrane prepared has noncircular lumen, when the "weak" or "soft" coagulation is used. To increase the fabrication solution stability during membrane formation, dope viscosity was focused in this experiment. Dimethyl acetamide (DMAc) was used as solvent as well as internal coagulant, and the additives including LiCl, water and surfactant Span were chosen to investigate their effect oil the viscosity of the fabrication solution. The dope viscosity will greatly increase after adding LiCl, while the variety of dope viscosity is unconcerned in the fabrication solution concentration as adding water. The homogenization and stability of the fabrication solution are improved by adding Span,and the viscosity increases at the same time. Without increasing PVDF concentration, the stability of the nascent membrane was improved by increasing the fabrication viscosity. The PVDF hollow fiber membrane with the structure of single outer skin layer and finger-like pore through the cross-section, has been successfully fabricated. The mean pore radius and water flux of the single skin hollow fiber membrane were greatly improved.

The influence of support layer structure on mass transfer in pervaporation of composite PDMS–PSF membranes

INFLUENCE OF PSF SUPPORT LAYER STRUCTURE ON THE PERVAPORATION PERFORMANCE OF PDMS/PSF COMPOSITE MEMBRANES

Effect of solvent concentration on development of macrovoids of PVDF phase-diversion membranes

Effect of Support Layer on Pervaporation Performance of PDMS Composite Membranes

Porous PVDF membranes containing amphiphilic comblike polysiloxane formed via phase inversion process

Influence of Support Layer of Composite PDMS Membranes on Performance of Hydrophobic Pervaporation

Influence of Solvents on the PVDF Membrane Properties

Modification of Porous Poly(Vinylidene Fluoride) Membrane Using Amphiphilic Polymers with Different Structures in Phase Inversion Process

Polymorphism in Porous Poly(vinylidene Fluoride) Membranes Formed Via Immersion Precipitation Process

Influence of support layer structure on mass transport of alcohols by pervaporation

Preparation of Stable Multilayer PDMS Composite Pervaporation Membrane Incorporated with In-Situ Transformed Metal Organic Frameworks for Enhanced Butanol Recovery

Influences of Support Layer Hydrophilicity on Morphology and Performances of Polyamide Thin-Film Composite Membrane

Preparation of Reverse Osmosis Composite Membrane with High Flux by Interfacial Polymerization of Mpd and Tmc

Effect of Process Conditions of Interfacial Polymerization on Performance of Reverse Osmosis Composite Membrane

Combining dip-coating and rotate-drying to preparation of PDMS on SiC tubular support with macropore for high pervaporation performance

Influence of Dope Viscosity on the Fabrication of Pvdf Hollow Fiber Membranes with Single Skin Layer

Pervaporation performance of PDMS composite membranes for separation of ethanol/water mixtures(Ⅱ)and effect of membrane preparation conditions

Influence of support layer pore size on interfacial polymerization and polyamide selective layer characterization

PDMS/PVDF pervaporation composite membrane, preparation method and application thereof

Improvement on Surface Hydrophily of Hollow Fiber-Supported PDMS Gas Separation Membrane by PVP Modification

A molecular level based parametric study of transport behavior in different polymer composite membranes for water vapor separation