Abstract:Gel polymer electrolyte films (GPEs) based on polyacrylonitrile (PAN) complexed with NaF salt and an Al2O3 nanofiller were prepared via solution cast method. Structural studies were performed to investigate the order of conductivity under the influence of salt and nanofillers. The prepared films were characterized using energy dispersive x-ray spectrometry (EDS) to determine the chemical composition in wt%. EDS studies reveal that PAN–NaF with Al2O3 ceramic filler decreases the degree of crystallinity with increasing concentration of the nanofiller. The UV–Vis spectrum was recorded by a Hewlett-Packard HP8452A diode array spectrometer. The structural effect of salt and nanoparticles on the conductivity was also confirmed by UV–Vis spectroscopy. The mechanical properties of the prepared polymer electrolytes were determined using a Universal Tensile Machine (Instron Model 5565, Canada) with a constant crosshead speed of 10 mm/min. The addition of nanoparticles increased both the modulus and the strength of the polymer nanocomposites. Both the tensile strength and Young’s modulus increased with increasing functionalized nanoparticle loading. The change in transition temperature caused by the incorporation of the Al2O3 nanofiller and plasticizer into the PAN+NaF complex was studied by differential scanning calorimetry (DSC) analysis. Additionally, DSC thermograms were recorded to measure the glass transition temperature and melting temperature of PAN-based electrolytes using a Mettler instrument. Conductivity studies were carried out for all the prepared polymer electrolytes to understand the conduction mechanism. The role of the ceramic phase is to reduce the melting temperature, which is ascertained from DSC. The sample containing PAN:NaF (70:30) exhibits the highest conductivity of 1.82 x 10−4 S cm−1 at room temperature (303 K) and 2.96 x 10−3 S cm−1 at 378 K. The polymer electrolytes considered in the present study exhibited an Arrhenius type of conduction. The polymer electrolyte containing 3 wt% Al2O3 nanofiller showed an ionic conductivity of 5.96 × 10−3 S cm−1. To determine transfer numbers, Wagner’s polarization method can be used. From these studies, it is observed that the conduction mechanism is predominantly due to ions. Using this (PAN–NaF– Al2O3) (70:30:3) electrolyte, a solid-state electrochemical cell was fabricated, and its discharge profiles were studied under a constant load of 100 kΩ. Finally, several cell profiles associated with this cell were evaluated and reported.

Gel polymer electrolytes based on polyacrylonitrile and a novel quaternary ammonium salt for dye-sensitized solar cells

Polyaniline-grafted silica nanocomposites-based gel electrolytes for quasi-solid-state dye-sensitized solar cells

A Novel Polymer Quaternary Ammonium Iodide and Application in Quasi-Solid-state Dye-Sensitized Solar Cells

Electrochemical and structural characterization of polyacrylonitrile (PAN)–based gel polymer electrolytes blended with tetrabutylammonium iodide for possible application in dye-sensitized solar cells

Polyacrylonitrile-based gel polymer electrolytes for dye-sensitized solar cells: a review

Efficiency enhancement in dye-sensitized solar cells with a novel PAN-based gel polymer electrolyte with ternary iodides

Effect of incorporating different polyaniline‐surface modified nanosilica content into polyurethane‐based quasi‐solid‐state electrolyte for dye‐sensitized solar cells

A quasi-solid-state dye-sensitized solar cell based on the stable polymer-grafted nanoparticle composite electrolyte

Transparent Succinonitrile-Modified Polyacrylate Gel Polymer Electrolyte for Solid Electrochromic Devices

Poly(acrylamide-co-acrylic acid)-based gel polymer electrolytes incorporated with sodium iodide for dye-sensitized solar cells (DSSCs)

A Novel Composite Polymer Electrolyte Containing Room-Temperature Ionic Liquids and Heteropolyacids for Dye-Sensitized Solar Cells

Preparation and Characterization of Novel Polymer-Based Gel Electrolyte for Dye-Sensitized Solar Cells Based on poly(vinylidene fluoride-co-hexafluoropropylene) and poly(acrylonitrile-co-butadiene) or poly(dimethylsiloxane) bis(3-aminopropyl) Copolymers

Effect of PEG Molecular Weight on the Polyurethane-Based Quasi-Solid-State Electrolyte for Dye-Sensitized Solar Cells

Gel Electrolytes Containing Several Kinds of Particles Used in Quasi-Solid-State Dye-Sensitized Solar Cells

Structural, Optical, and Electrical Studies of PAN-Based Gel Polymer Electrolytes for Solid-State Battery Applications

High-Performance PVDF-HFP Based Gel Polymer Electrolyte Modified by Core-Shell SiO2-PMMA for Electrochromic Devices

Review on mixed cation effect in gel polymer electrolytes for quasi solid-state dye-sensitized solar cells

Crosslinked poly(acrylonitrile–glycidyl methacrylate) as a novel gel polymer electrolyte

Solidifying Liquid Electrolytes with Fluorine Polymer and Silica Nanoparticles for Quasi-Solid Dye-Sensitized Solar Cells

Low-Dose Imidazolium Cation Grafted Polymeric Nanotubes for Quasi-Solid-State Dye-Sensitized Solar Cells

Polyvinylidene fluoride‐co‐hexafluoropropylene polymer gel electrolyte‐enabled dye‐sensitized solar cell for sustainable energy