Heteropolyacid-Catalyzed Synthesis of Aspirin

Yanqing Peng,Gonghua Song

DOI: https://doi.org/10.1007/s00897000384a

2000-01-01

The Chemical Educator

Abstract:Aspirin was synthesized from salicylic acid and acetic anhydride in the presence of noncorrosive 12-tungstophosphoric acid as an alternative catalyst to liquid acids, e.g., sulfuric acid. This process can be carried out at room temperature and gives a reasonable yield of isolated product.

What problem does this paper attempt to address?

Preparation of Solid Acid – Activated Carbon as Catalyst in Aspirin Synthesis

Firman Kurniawansyah,Sarah Syifa,Ronal Marada Pakpahan,Hikmatun Ni’mah,Achmad Roesyadi

DOI: https://doi.org/10.1088/1757-899X/1053/1/012059

2021-02-26

IOP Conference Series: Materials Science and Engineering

Abstract:Pharmaceutical synthesis commonly relies on a homogeneous acid catalyst, which is relatively simple in application yet problematic in product purification procedures. This study was an effort to investigate an alternative replacement for homogeneous acid catalysts with an acidified solid catalyst, developed from activated carbon. The activated carbon catalyst had been treated with sulfuric acid before it was applied to produce aspirin (acetylsalicylic acid) through catalytic acetylation route. Using atmospheric pressure reaction, conducted at 353 K, aspirin was successfully synthesized. When salicylic acid and acetic acid glacial were used as reactants, approximately 9-10 % reaction yield could be obtained. Replacement of acetic acid with acetic anhydride in the acetylation reaction produced an overall yield as high as 28 %.
Catalytic Synthesis of Aspirin with Sodium Acetate

Li Cheng-fan

Abstract:Catalytic synthesis of Aspirin over pretreated sodium acetate using salicylic acid and acetic anhydride as starting materials. The results showed when the amount of salicylic acid was 3.0 g, acetic anhydride 6 mL, sodium acetace3%(wt% of salicylic acid and acetic anhydride),55 ℃ reaction for 50 min,the yield of purified Aspirin was 81.9%.The product is characterized by IR and NMR spectrometry. The effects of dose catalyst-to-crude ratio, reaction temperature and reaction time on the yield of Aspirin are discussed.

Chemistry,Engineering
Study on catalytic synthesis of aspirin with potassium dihydrogen phosphate

Kong Xiang-ping

Abstract:Aspirin was synthesized from salicylic acid and acetic anhydride with potassium dihydrogen phosphate catalyst by ultrasonic oscillation.The optimum laboratory conditions obtained by orthogonal experiments were that 3.0 g salicylic acid,6.2 mL acetic anhydride(1 ∶3,mol/mol),0.5 g potassium dihydrogen phosphate,reacted 30～40 min at 75～80 ℃.The FTIR spectrum of the product was completely consistent with the standard spectrum.The potassium dihydrogen phosphate may be used repeatedly as catalyst with nearly 90% recovery.Comparing with the concentrated sulphuric acid catalysis,the potassium dihydrogen phosphate catalyst may be recycled,and has the advantages of security,environmental protection.This method is suitable for undergraduate teaching and industrial production.

Chemistry
Catalytic synthesis of aspirin by trifluoromethanesulfonic acid

Wang Jun

Abstract:Trifluoromethanesulfonic acid was used as the catalyst for synthesis of aspirin from salicylic acid and acetic anhydride at 50 ℃.The effects of catalyst amounts,molar ratio of salicylic acid to acetic anhydride and reaction time on the product yield was investigated.The results showed that the optimum reaction conditions were found as follows:0.2% catalyst based on salicylic acid,molar ratio of salicylic acid to acetic anhydride 1∶ 2.0,and reaction time was 50 min.Under this condition,the yield of aspirin was 90.4%.

Chemistry
Synthesis of Salan (salalen) Ligands Derived from Binaphthol for Titanium-Catalyzed Asymmetric Epoxidation of Olefins with Aqueous H2O2

Donglu Xiong,Mei Wu,Shoufeng Wang,Fuwei Li,Chungu Xia,Wei Sun

DOI: https://doi.org/10.1016/j.tetasy.2010.01.023

2010-01-01

Abstract:A series of chiral salan (salalen) ligands, easily prepared from the aldehyde derived from chiral binaphthol, are effective ligands for the titanium-catalyzed asymmetric epoxidation of olefins with aqueous H2O2 as the oxidant. One of the titanium–salan complexes was determined by X-ray crystallography.
Catalytic Synthesis of Aspirin with Sodium Acetate by Ultrasonic Wave

Y. Yuan

Abstract:Salicylic acid and acetic anhydride used as raw materials,sodium acetate as catalyst under different conditions for synthesis of aspirin,the optimized conditions were as follows: crystallization time was 2 h,material mole ratio of salicylic acid and facetic anhydride was 1∶2. 5,reaction time was 20 min,reaction temperature was 75 ℃,and the dosage of catalyst was 8% of salicylic acid. Under these conditions,the yield of Aspirin was 88%. This method was litter equipment corrosion and litter environmental pollution than traditional methods,and was an environmentally friendly and efficient way of synthesis of Aspirin.

Chemistry
Using Supported Heteropoly Acids as a Eco-Friendly and Recyclable Catalyst for Efficient Synthesis of Acetylsalicylic Acid

Nesarak Eslamiyakhforouzan,A. Ahmadpour,M. Heravi,Hadiseh Nazari,F. Bamoharram

2010-10-25

Abstract:Catalytic performance of supported Preyssler and Keggin heteropolyacids on silica, H14[NaP5W30O110]/SiO2 and H3[PW12O40]/SiO2, have been studied at room temperature for highly selective and rapid liquid-phase O-acetylation of salicylic acid in order to synthesize acetylsalicylic acid which is well-known century-old chemical pharmaceutical. The usual catalysts in acetylsalicylic acid synthesis are toxic liquid acids such as HNO3 and H2SO4, which would cause serious corrosive and other environmental problems. The performance of silica-supported preyssler and Keggin with various loadings is compared with sulfuric acid method. The heteropolyacids show almost 25% more activity compared with H2SO4.

Chemistry,Environmental Science
Condition investigation on the synthesis of Aspirin by vitamin C catalyst

H. Weile

Abstract:Objective:To synthesize Aspirin by using vitamin C as the catalyst,salicylic acid as the raw material and acetic anhydride as the acylating agent.Methods:The method of acetylation was used.Results:The synthesis conditions was determined,the temperature was 80℃,the reaction time was 40 min,the quantity of vitamin C was 0.2 g,the yield was 56.8%.Conclusion:The method is feasible,and the synthesis condition needs to be improved.

Chemistry,Medicine
The Synthesis and Analysis of Aspirin

Mariam El-Magbri

Abstract:Acetylsalicylic acid commonly known as aspirin is the most widely used drug in the world today. Its analgesic, antipyretic, and anti-inflammatory properties make it a powerful and effective drug to relive symptoms of pain, fever, and inflammation. The purpose of this experiment was to synthesize aspirin by reacting salicylic acid and acetic anhydride in the presence of phosphoric acid to form acetylsalicylic acid. After synthesis, the sample of acetylsalicylic acid was purified by recrystallization and TLC analysis was utilized to check the purity of the sample. The actual yield of aspirin synthesized was 0.546 grams and the theoretical yield was 2.628 grams, thus the percent yield was 20.77% resulting in a percent error of 79.22%. The Rf values of crude product, salicylic acid, and recrystallized product were 0.590 and 0.897, 0.818, and 0.606 and 0.879 respectively. Due to these Rf values, it was brought to the conclusion that the crude and recrystallized aspirin were composed of both salicylic acid and acetylsalicylic acid.

Chemistry,Medicine
Technical Conditions of Synthesizing 5-Bromo-2-hydroxy-3-(1-propionyl) Benzoic Acid Methyl Ester

张华,吕养心,辛成伟,钱超,陈新志

DOI: https://doi.org/10.3969/j.issn.1008-1100.2010.05.007

2010-01-01

Abstract:5-Bromo-2-hydroxy-3-(1-propionyl) benzoic acid methyl ester was synthesized by using salicylic acid as raw material.The mass of catalyst,molar ratio of methanol to salicylic acid in the esterification,the effects of the solvent,feeding mode and molar ratio of reactants in the C-acylation were respectively investigated. The product was characterized by IR and GC-MS.The result indicated that the optimum technical conditions were as follows:m(ion exchange resin):m(salicylic acid)=1.00%,n(methanol):n(salicylic acid) = 7:1,chloroform as solvent;ester was added into the chloroform solution of aluminum chloride;n(aluminum chloride):n(5- bromo-salicylic acid methyl ester):n(propionic anhydride) = 2:1:1.Under these conditions,the total yield of desired product was 74.52%.
Synthesis of Aspirin by Microwave Radiation

Wang Long

Abstract:Aspirin was synthesized through the method of microwave radiation with salicylic acid and acetic anhydride as raw materials.Catalytic effects of stronger sulfuric acid,aluminum chloride and anhydrous sodium carbonate were compared.The optimum synthetic conditions of aspirin were investigated.The results show that when aluminum chloride is used as catalyst,its amount is 3% of the salicylic acid mass,ratio of acetic anhydride and salicylic acid is 2.5∶1,microwave power is 200 W,radiation time is 60 s,yield of aspirin can reach 81.4%.

Chemistry
Synthesis of aspirin butanol ester

Zhang Yan-jun

Abstract:OBJECTIVE To synthesize prodrug Aspirin butanol ester.METHODS Aspilin was obtained by the reaction of Salicylate and Anhydride and the aspirin butanol ester was synthesized with aspilin and butanol in the dehydration of DCC.RESULTS Four aspirin butanol esters were synthesized.CONCLUSION The structures of the target compounds were characterized by IR,1H NMR.

Chemistry,Medicine
Macrocycles 14 - Polycondensations of Aspirin and Other Monomers of Salicylic Acid

LM Tang,M Rabenstein,HR Kricheldorf

DOI: https://doi.org/10.1002/1521-3935(20010601)202:9<1497::aid-macp1497>3.0.co;2-a

IF: 2.996

2001-01-01

Macromolecular Chemistry and Physics

Abstract:Aspirin was polycondensed at various temperature-time combinations with or without the addition of a catalyst. Furthermore, several polycondensations of both the trimethylsilyl ester of aspirin, and o-trimethylsiloxybenzoyl chloride were conducted. Viscosity and GPC measurements indicated that from all three monomers only oligoesters having number average molecular weights (M̄n) ≤ 1 500 Da were obtained. FAB mass spectra of crude reaction products revealed that cyclic oligoesters (having DPs up to 7) were formed as the main reaction products under all circumstances. When ortho and meta trimethylsiloxybenzoyl chloride were copolycondensed with variation of the molar ratio, the molecular weights decreased with higher feed ratios of the salicylic acid derivative. Obviously, the salicylic monomer favored cyclization reactions at the expense of the chain growth. The predominant formation of cyclic oligoesters (with M̄ns up to 5 000 Da) was confirmed by MALDI-TOF mass spectra.
Improvement of Synthetic Method of Lysine Aspirin

Kun Chen,Xin Zhu,Qikang Tian,Lan Zhang

DOI: https://doi.org/10.1088/1757-899x/677/2/022054

2019-12-01

IOP Conference Series: Materials Science and Engineering

Abstract:Abstract The synthesis method of lysine aspirin was improved, and the new method was applied to the synthesis of similar new drugs. Aspirin is reacted with an aqueous solution of sodium hydrogen carbonate to prepare its sodium salt, and lysine was reacted with a sodium salt thereof in water to prepare lysine aspirin. The product was identified by melting point, infrared spectroscopy and high performance liquid chromatography; the cysteine salts of aspirin was prepared by this method, and the product was identified by micro melting point apparatus and infrared spectroscopy. Lysine aspirin was synthesized by the reaction of sodium acetylsalicylate with lysine. The author measured the melting point and infrared absorption spectrum of the cysteine salt sample of aspirin, which was initially determined to be possible. The new method offers the possibility to expand the production route of lysine aspirin, and also provides new ideas for the preparation of similar new drugs.
Synthesis of acetyl salicylic acid with sodium benzoate as catalytic

Tian Xu

2006-01-01

Abstract:Acetyl salicylic acid was catalytic synthesized by the reaction of salicylic acid with acetic anhydride catalyzed by sodium benzoate.The target compound could be obtained in 82.8% yield after heating of the(reaction) mixtures(salicylic acid 2.0?g,acetic anhydride 2.8?mL,sodium benzoate 8%～10%(w of salicylic acid)),60～65?℃ reaction for 25～30?min,which indicated that sodium benzoate was an environment-friendly catalyst with safety,little pollution and high catalytic performance and could be used in the future (industrial) applications.
Synthesis of Acetylsalicylic Acid with Rare Earth Chloride Catalyst

Bai He-long

Abstract:Acetylsalicylic acid was synthesized with salicylic acid and acetic anhydride as reactants,rare earth trichloride as catalyst.The influence of factor was discussed.The appropriate conditions were determined to be:molar ratio of salicylic acid and acetic anhydride:1:2.0,catalyst:EuCl3,reaction time:40 minutes,reaction temperature:85℃～90 ℃,the yield can be over 88%.

Chemistry
Synthesis of Acetylsalicylic Acid with Iodine as Catalyst

Yu Fang-yuan

Abstract:cetylsalicylic acid was synthesized from salicylic acid and acetic anhydride catalyzed by iodine. The results showed that the method for synthesizing acetylsalicylic acid with iodine as catalyst featured rapid reaction rate, less dosage of catalyst, obtained product with high purity and no pollution to environment etc. The optimum esterification conditions were as follows: molar ratio of acetic salicylic acid to anhydride to iodine was 2:1:0.0039, reaction time was 30 min, reaction temperature was at range of 80 -85℃, and the yield can be reached 85.9%.

Chemistry
Aspirin: an efficient catalyst for synthesis of bis (pyrazol-5-ols), dihydropyrano[2,3-c]pyrazoles and spiropyranopyrazoles in an environmentally benign manner

Maryam Fatahpour,Fatemeh Noori Sadeh,Nourallah Hazeri,Malek Taher Maghsoodlou,Mojtaba Lashkari

DOI: https://doi.org/10.1007/s13738-017-1133-x

2017-05-06

Journal of the Iranian Chemical Society

Abstract:This article aimed to present two facile and environmental friendly routes for the rapid assembly of biologically active compounds including pyrazol core using aspirin as a novel and green catalyst. The synthesis of bis(pyrazol-5-ol) derivatives was developed via one-pot, pseudo-five-component condensation, and the target dihydropyrano[2,3-c]pyrazoles and spiropyranopyrazoles were prepared by one-pot, four-component reaction. These reactions can be performed in tandem from readily available starting materials. The main merits of the present methods are operational simplicity, no need for column chromatography, inexpensive materials, avoidance of harmless and corrosive acid catalysts, short reaction times, good yields of the products, and utilization of aspirin as a non-toxic, cheap, commercially available, and efficient catalyst.Graphical abstract

chemistry, multidisciplinary
Catalytic synthesis of Aspirin over sodium bisulfate

Lin De

Abstract:Catalytic synthesis of Aspirin over pretreated sodium bisulfate is studied. The effects of dose of catalysttocrude ratio, reaction time and reaction temperature on the yield of Aspirin are discussed.The results showed when the amount of salicylic acid was 3.0 g,acetic anhydride 6 ml,sodium bisulfate 3.16%(wt% of salicylic acid and acetic anhydride), 75 ℃ reaction for 30 min,the yield of purified Aspirin was 76.9%. The product is characterized by IR and UV spectrometry. This method had the application value.

Chemistry

Heteropolyacid-Catalyzed Synthesis of Aspirin

Preparation of Solid Acid – Activated Carbon as Catalyst in Aspirin Synthesis

Catalytic Synthesis of Aspirin with Sodium Acetate

Study on catalytic synthesis of aspirin with potassium dihydrogen phosphate

Catalytic synthesis of aspirin by trifluoromethanesulfonic acid

Synthesis of Salan (salalen) Ligands Derived from Binaphthol for Titanium-Catalyzed Asymmetric Epoxidation of Olefins with Aqueous H2O2

Catalytic Synthesis of Aspirin with Sodium Acetate by Ultrasonic Wave

Using Supported Heteropoly Acids as a Eco-Friendly and Recyclable Catalyst for Efficient Synthesis of Acetylsalicylic Acid

Condition investigation on the synthesis of Aspirin by vitamin C catalyst

The Synthesis and Analysis of Aspirin

Technical Conditions of Synthesizing 5-Bromo-2-hydroxy-3-(1-propionyl) Benzoic Acid Methyl Ester

Synthesis of Aspirin by Microwave Radiation

Synthesis of aspirin butanol ester

Macrocycles 14 - Polycondensations of Aspirin and Other Monomers of Salicylic Acid

Improvement of Synthetic Method of Lysine Aspirin

Synthesis of acetyl salicylic acid with sodium benzoate as catalytic

Synthesis of Acetylsalicylic Acid with Rare Earth Chloride Catalyst

Synthesis of Acetylsalicylic Acid with Iodine as Catalyst

Aspirin: an efficient catalyst for synthesis of bis (pyrazol-5-ols), dihydropyrano[2,3-c]pyrazoles and spiropyranopyrazoles in an environmentally benign manner

Catalytic synthesis of Aspirin over sodium bisulfate