Abstract:With the continuous improvement of various armor protection technologies, the armor protection performance has increased significantly, and then the damage performance requirements of armor-piercing ammunition have also increased. In order to improve the penetration ability of the liner, a new three-layer liner structure is designed in this paper. The jet forming process was simulated by AUTODYN software. The mechanism of shaped jet forming of three-layer liner was studied. The reason why the penetration depth of three-layer liner was higher than that of ordinary liner was explained. The influence of three-layer liner on the propagation of detonation wave and the change of pressure when detonation wave acted on liner were found, which provided a new idea for improving the penetration depth of jet. The influence of liner material, cone angle and stand-off on jet forming and penetration was also studied by orthogonal optimization experiment, and the structural parameters with the best penetration performance were obtained. The results show that the pressure at the convergence point increases first and then decreases during the formation of the jet of the three-layer liner. The pressure at the convergence point when the three-layer liner material is from low impedance to high impedance from the outside to the inside is much larger than the pressure at the convergence point from high impedance to low impedance. When the three-layer liner material is Al 2024-Copper–Tantalum from the outside to the inside, the pressure at the convergence point of the three-layer liner at different times is higher than that of the double-layer liner and the single-layer liner. Reasonable matching of different impact impedance materials in the three-layer liner can greatly improve the pressure value of the detonation wave acting on the cone liner. The maximum pressure at the convergence point on the axis is 39.10 GPa, which is 22.00% higher than that of the double-layer liner at the convergence point, and 53.03% higher than that of the single-layer liner at the convergence point. The orthogonal design test scheme is simulated and analyzed. The penetration depth is taken as the observation index, and the range analysis is adopted. The results show that the material matching of the three-layer liner has the greatest influence on the depth of the jet penetrating the target plate, followed by the cone angle of the three-layer liner. Relatively speaking, the stand-off has the least influence on the result. Reasonable matching of materials with different impact impedances in the three-layer liner can maximize the penetration depth of the jet into the target plate.

Finite Element Simulation and Experimental Comparison on Perforating Casing of Peroration Bullet

3 Dimensional Finite Element Simulation on Perforating Casing of Peroration Bullet

Finite Element Simulation on Jet Flow of SDP45 Type Peroration Bullet

Finite Element Analysis and Simulation of Oilfield Perforating Charge Penetration Depth

Study on Forming Law and Penetration of a Spherical Cone Composite Structure Liner Based on the Explosion Pressure-Coupling Constraint Principle

Formation and Penetration Properties of a Shaped Charge with Zr41.2Ti13.8Cu12.5Ni10Be22.5 Liner

Numerical Simulation of the Shaped Charge Jet Formation and Penetration Through the Wall of Perforating Gun

Numerical Simulation of Effect of Liner’s Structure on Performance of Shaped Charge Jet

Density Effect of PTFE-Copper Powder Metallurgy Liner Material on the Perforation Performance of Shaped Charge Jets

Experimental and numerical study on the flight and penetration properties of explosively-formed projectile

Numerical Simulation and Analysis of Shelled Explosive Penetrated but Not Detonated

Numerical Simulation of Conical Shaped Charge Jet Formation Process

Investigation of Penetration Performance of Zr-based Amorphous Alloy Liner Compared with Copper

A study on the surface overpressure distribution and formation of a double curvature liner under a two-point initiation

Smooth Particle Hydrodynamics-Based Characteristics of a Shaped Jet from Different Materials

The Influence of Closed-Cell W-Shaped Liner Parameters on the Penetration Performance of Integral Annular Shaped Charge

Numerical simulation of the extruded process of Cased Telescoped Ammunition

Study on the detonation wave propagation of shaped charge with three-layer liner and its driving characteristics to liner

Experimental and Numerical Study on the Penetration Performance of a Shaped Charge

Investigation of the Fracture and Fragmentation of Implosively Driven Thin-Walled Cylindrical Shell: From Thermodynamic Analysis to CDEM Simulation

Numerical Investigation on Crack Formation and Penetration Mechanism between Adjacent Blastholes