Abstract:In this study, the cooperative effect of Mg and Si contents on the microstructural evolution, mechanical properties, and deformation behavior of the cast Al–Li–Mg–Si alloys is investigated. Five different Al–Li–Mg–Si alloys are prepared by conventional casting method, which are referred to as Alloy A-E. The results show that with the increase in the Mg content, the amount of lath-like Mg2Si precipitates and bulk-like AlLiSi particles increases, which leads to an improvement in the strength and ductility of alloys. The amount of intergranular Si-rich phases in Alloy D increases with the increase in the Si content. Further, a higher Si content in Alloy E promotes the formation of bulk-like AlLiSi. The geometric phase analysis (GPA) results reveal strain partitioning behavior at the interface of Mg2Si precipitates and AlLiSi particles, which follows the Orowan looping or dislocation cutting strengthening mechanism. The geometrically necessary dislocation (GND) density calculation results suggest that the lath-like Mg2Si precipitates play a critical role in the deformation behaviors of Alloy A-C. The hindering effect of lath-like Mg2Si precipitates on the movement of dislocations decreases the GND density gap between high-angle grain boundaries or junctions and grain interior and improves the resistance to deformation. However, the deformation behaviors of Alloy D and E with higher Si content are mainly governed by the intergranular Si-rich phases. Finally, a methodological framework is established to elucidate the effect of precipitates and/or intergranular phases on the deformation behaviors of materials using a combination of GPA and GND density calculation methods.

Prediction of the Effect of Alloying Elements on in Situ Reaction in Synthesizing (aln+mg2si)/mg Composites

Prediction of the effect of alloying elements on in-situ reaction in synthesizing (AIN+Mg2Si)/Mg composites

Thermodynamics and Kinetics to Alloying Addition on In-Situ AlN/Mg Composites Synthesis via Displacement Reactions in Liquid Mg Melt

Prediction of chemical stability in SiCp/Al composites with alloying element addition using Wilson equation and an extended Miedema model

Size control of in situ formed reinforcement in metal melts-theoretical treatment and application to in situ (AlN + Mg2Si)/Mg composites

Thermodynamics of the Effect of Alloying Additions on In-Situ Reaction to Synthesize TiC/Mg Composites

Effect of Mg on Nucleation Process of Recrystallization in Al–Mg–Si/SiCp Composite

Thermodynamic Effect of Alloying Addition on In-Situ Reinforced TiB 2 /al Composites

Thermodynamic Effects of Alloying Elements on Solid-State Interfacial Reactions in a Multicomponent System: Theoretical Treatment and Application in SiC f /Ti Composites

Influence of Processing Parameters on the Microstructure of (aln+mg2si)/mg Metal Matrix Composites

Fabrication and Formation Mechanism of in Situ AlN and Mg2Si Particles-Reinforced Mg Matrix Composites

Work of Adhesion in Al/SiC Composites with Alloying Element Addition

Cooperative Effect of Mg and Si Contents on the Microstructural Evolution, Mechanical Performance, and Deformation Behavior of Cast Al–Li–Mg–Si Alloys

Promoting Effect of Silicon Particles on Gas-Diffusion-reaction System: In-situ Synthesis of AlN in Al-Si Materials

Effect of Alloying Elements on the Short-Range Orders and Atomic Diffusion Behavior of Liquid Al−9Si Cast Alloys

The Effect of Alloying Elements on Formation and Evolution Mechanism of Manganese‐Containing Inclusions in Medium/High‐Manganese Steels

Predicting the Cooperative Effect of Mn–Si and Mn–Mo on the Incomplete Bainite Formation in Quaternary Fe–C Alloys

The Effect of Mn on the Microstructure of Spray-Deposited Al–20Si–5Fe–3Cu–1Mg Alloy

Effects of Mg, Si and multiple rare earth addition on microstructures of Al 3Ti /A356 composites

Effects of Mg, Si and Multiple Rare Earth Addition on Microstructures of Al<sub>3</sub>Ti /A356 Composites

Model Prediction of Thermodynamics Activity in Multicomponent Liquid Alloy