In-Situ TEM Studies of the Deformation Mechanism of Nanocrystaline Ni

Z Shan,E A Stach,J M K Wiezorek,D M Follstaedt,J A Knapp,S X Mao

DOI: https://doi.org/10.1017/s1431927605510432

IF: 4.0991

2005-01-01

Microscopy and Microanalysis

Abstract:Extended abstract of a paper presented at Microscopy and Microanalysis 2005 in Honolulu, Hawaii, USA, July 31--August 4, 2005

What problem does this paper attempt to address?

Revealing the Mechanical Bending Mechanisms of Single-Crystalline Rutile TiO2 Nanowires Near Room Temperature: Implications for Nanostructured Semiconductors

Qiong Liu,Arixin Bo,Haifei Zhan,Liangzhi Kou,Yuantong Gu

DOI: https://doi.org/10.1021/acsanm.1c01864

IF: 6.14

2021-01-01

ACS Applied Nano Materials

Abstract:Understanding the deformation mechanisms of rutile titanium dioxide (TiO2) nanowires (NWs) helps to improve the working reliability of TiO2-based nanoelectrical-mechanical systems and better apply strain engineering to these materials. This work investigated the bending deformation mechanisms at the atomic scale using in situ transmission electron microscopy (TEM) near room temperature. Large bending strains of 3.0% to 5.1% could be observed on individual TiO2 NWs near room temperature. The large bending deformation was attributed to the formation of rich stacking faults (SFs) lying on (10 (1) over bar) planes and the nucleation and glide of extended dislocations belonging to the {10 (1) over bar}< 101 > slip system.
In Situ TEM Study on the Nanomechanical Behaviors of Metallic Nanowires

Jiangwei Wang

2014-01-01

Abstract:In this dissertation, the relationships between structure-mechanical properties-deformation mechanisms in face-centered cubic (FCC) and body-centered cubic (BCC) metallic nanowires have been studied using in situ TEM nanomechanical testing. It is well known that smaller is stronger and the widely-observed size effect is believed to arise from dislocation interactions inside nanocrystals. However, the interaction mechanisms in small-volume nanocrystals remain unexplored. Here, it was found that surface-nucleated dislocations can strongly interact inside the confined volume of Au nanowires, which led to a new type of dislocation-originated stacking fault tetrahedra (SFT), at variance to the widely-believed vacancy-originated SFT. The atomic-scale processes of nucleation, migration and annihilation of dislocation-originated SFT were revealed, shedding new light onto the strain hardening and size effect in small-volume materials. Although nanoscale twinning is an effective mean to enhance the strength of metals, twin-size effect on the deformation and failure of nanotwinned metals remains largely unexplored, especially at the minimum twin size. Here, a new type of size effect in nanotwinned Au nanowires is presented. As twin size reaches the angstrom-scale, Au nanowires exhibit a remarkable ductile-to-brittle transition that is governed by the heterogeneous-to-homogeneous dislocation nucleation transition. Quantitative measurements show that approaching such a nanotwin size limit gives rise to the ultra-high strength in Au nanowires, close to the ideal strength limit of perfect Au. Twinning is a fundamental deformation mode that competes against dislocation slip in crystals. At the nanoscale, higher stresses are required for plastic deformation than that in bulk, which favors twinning over dislocation slip. Indeed, deformation twinning has been well-documented in FCC nanocrystals. However, it remains unexplored in BCC nanostructures. Here, it shows that twinning is the dominant deformation mode in BCC-tungsten nanocrystals. A competition between twinning and dislocation slip occurs when changing the loading orientations, attributed to the defect growth controlled plasticity in BCC nanocrystals. Several important commonalities and differences in FCC and BCC nanocrystals deforming at nanoscale are further proposed. The results from this dissertation advance fundamental understanding of plastic deformation in a broad class of metals and alloys, and are of technological importance for degradation control and future design of ultra-strength nanomaterials.
In Situ Nanomechanical Testing of Twinned Metals in a Transmission Electron Microscope

Li Nan,Wang Jiangwei,Mao Scott,Wang Haiyan

DOI: https://doi.org/10.1557/mrs.2016.66

IF: 5

2016-01-01

MRS Bulletin

Abstract:This article focuses on in situ transmission electron microscope (TEM) characterization to explore twins in face-centered-cubic and body-centered-cubic monolithic metals, and their impact on the overall mechanical performance. Taking advantage of simultaneous nanomechanical deformation and nanoscale imaging using versatile in situ TEM tools, direct correlation of these unique microscopic defects with macroscopic mechanical performance becomes possible. This article summarizes recent evidence to support the mechanisms related to strengthening and plasticity in metals, including nanotwinned Cu, Ni, Al, Au, and others in bulk, thin film, and nanowire forms.
A Molecular Dynamics Study on Mechanical Performance and Deformation Mechanisms in Nanotwinned NiCo-based Alloys with Nano-Precipitates under High Temperatures

Zihao Yu,Hongyu Wang,Ligang Sun,Zhihui Li,Linli Zhu

DOI: https://doi.org/10.1088/1674-1056/ad6cca

2024-01-01

Abstract:Molecular dynamics simulations are performed to investigate the mechanical behavior of nanotwinned NiCo-based alloys containing coherent L12 nano-precipitates at different temperatures, as well as the interactions between the dislocations and nano-precipitates within the nanotwins. The simulation results demonstrate that both the yield stress and flow stress in the nanotwinned NiCo-based alloys with nano-precipitates decrease as the temperature rises, because the higher temperatures lead to the generation of more defects during yielding and lower dislocation density during plastic deformation. Moreover, the coherent L12 phase exhibits excellent thermal stability, which enables the hinderance of dislocation motion at elevated temperatures via the wrapping and cutting mechanisms of dislocations. The synergistic effect of nanotwins and nano-precipitates results in more significant strengthening behavior in the nanotwinned NiCo-based alloys under high temperatures. In addition, the high-temperature mechanical behavior of nanotwinned NiCo-based alloys with nano-precipitates is sensitive to the size and volume fraction of the microstructures. These findings could be helpful for the design of nanotwins and nano-precipitates to improve the high-temperature mechanical properties of NiCo-based alloys.
In Situ Atomistic Observation of the Deformation Mechanism of Au Nanowires with Twin–twin Intersection

Shuchun Zhao,Qi Zhu,Xianghai An,Hua Wei,Kexing Song,Scott X. Mao,Jiangwei Wang

DOI: https://doi.org/10.1016/j.jmst.2020.03.044

2020-01-01

Journal of Material Science and Technology

Abstract:Twin–twin intersections are often observed in face-centered cubic (FCC) metallic nanostructures, which have important contributions to the plastic deformation and strengthening of FCC metals with low stacking fault energies. However, a deep insight into the underlying mechanism involved in the formation and evolution of twin–twin intersections remains largely lacking, especially in experiments. Here, by conducting the in situ straining experiments under high resolution transmission electron microscope (TEM), we directly visualize the dynamic evolution of a twin–twin intersection in Au nanowire at the nanoscale. It shows that dislocations in the incoming twin can either glide onto or transmit across the barrier twin via dislocation interaction with the twin boundary, resulting in the twin–twin intersection. Dynamic twinning and de-twinning of the twin–twin intersection govern the whole deformation of the nanowire. These findings reveal the dynamic behaviors of twin–twin intersection under mechanical loading, which benefits further exploration of FCC metals and engineering alloys with twin–twin intersection structures.
In-Situ HR-TEM Characterizations on Individual Carbon Nanotubes During Its Manipulation, Deformation and Growth

Chuanhong Jin,Kazu Suenaga,Sumio Iijima

DOI: https://doi.org/10.1017/s1431927609092691

IF: 4.0991

2009-01-01

Microscopy and Microanalysis

Abstract:Extended abstract of a paper presented at Microscopy and Microanalysis 2009 in Richmond, Virginia, USA, July 26 – July 30, 2009
In-situ Fabrication, Manipulation and Property Measurements of Single Nanotubes and Nanowires with Near Atomic Resolution

L-M Peng,Q Chen,JY Wang,MS Wang,ZY Zhang,CH Jin,XL Wei

DOI: https://doi.org/10.1017/s1431927606069510

IF: 4.0991

2006-01-01

Microscopy and Microanalysis

Abstract:Extended abstract of a paper presented at Microscopy and Microanalysis 2006 in Chicago, Illinois, USA, July 30 – August 3, 2005
Research on Deforming Mechanism of Nanocrystalline Cu Thin Film under Contact Deformation

ZOU Pengyuan,LIU Xiaoping,ZHANG Yuefei

DOI: https://doi.org/10.3969/j.issn.1000-6281.2015.05.006

2015-01-01

Abstract:In this paper, magnetron sputtering and Lithography technology were used to fabricate the “Cu/photoresist/ SiO2/Si”structure. Indentation deformation was conducted on Cu nanocrystalline thin film ( approximately 50nm) with indenter. Using the developed thin film in?situ transmission technology, the thin film with indentation area could be directly transformed onto the copper grid for in?situ transmission electronic microscope research ( TEM ) . The deforming mechanism of nanocrystalline Cu thin film in indentation area was observed by high resolution electronic microscope ( HRTEM ) . The results showed that deformation twinning constituted the main deformation mode in the grains ( <40nm). TEM results presented that twinning could be formed by the emission of partial dislocations from grain boundary, which could change the shape of grain. On the other hand, the self?multiplication of partial dislocation in the grain could also form the deformation twinning on the twinning plane under local stress.
In Situ Tem Nanomechanics

Yu Q.,Legros M.,Minor A. M.

DOI: https://doi.org/10.1557/mrs.2014.306

IF: 5

2015-01-01

MRS Bulletin

Abstract:In situ transmission electron microscopy (TEM) nanomechanical testing has benefited from a number of recent technical developments related to both how deformation is imaged and how deformation is induced and measured inside a TEM instrument. These developments have led to new insights into the deformation mechanisms of a wide range of metals and alloys, as well as measurements of the unusual mechanical properties of small-scale objects such as whiskers and nanocrystals. Herein, we describe this recent progress through selected highlights of recent findings on the dynamic behavior of defects such as dislocations, twins, and grain boundaries.
Recent Electron Microscopy Results on Micro- and Nanostructured Ni-Ti-(X) Shape Memory Alloys

D. Schryvers,Wim Tirry,Zhiqing Yang,Shanshan Cao,He Tian,Rémi Delville

2009-01-01

Abstract:The present contribution will focus on recent advanced transmission electron microscopy studies of Ni-Ti based alloys with the emphasis on features related to the martensitic transformation. The examples range from the atomic scale when looking at the atomic structure of a precipitate to the micron scale when looking at the configuration of these precipitates or to twin configurations in particular ternary alloys. An example of the first is the refinement of the atomic structure of a Ni4Ti3 precipitate formed in Ni-rich Ni-Ti alloys to enhance the shape memory behaviour. A slice-and-view study to obtain the 3D configuration of these precipitates is an example of the latter. Some other examples will be discussed as well.
In-situ observation of crack propagation through the nucleation of nanoscale voids in ultra-thin, freestanding Ag films

yuefei zhang,fei wang,peng zang,jin wang,shengcheng mao,xiaona zhang,junxia lu

DOI: https://doi.org/10.1016/j.msea.2014.09.056

2014-01-01

Abstract:A tensile technique was developed and coupled with in-situ transmission electron microscopy observations to directly characterize the crack propagation mechanism in sputter-deposited, ultra-thin, freestanding nanocrystalline Ag thin films with a thickness of 60nm. The developed technique directly revealed the fracture mechanism; the thin film with nanoscale grains exhibits ductile fracture behavior, and the crack propagates through void nucleation, growth, and coalescence ahead of the crack tip. A model for the energy release rate during the propagation of nanovoids was established to quantitatively characterize the equilibrium length of the voids. Based on experimental measurements and theoretical calculations, the effects of stress distribution and energy transformation on the nucleation position, equilibrium length, and growth rate of the nanovoids are discussed.
In situ observation of intergranular fracture propagation in nanocrystalline freestanding ultrathin tungsten film

Fei Wang,Yuefei Zhang,Junxia L��,Peng Zang,Jin Wang,Xiaona Zhang

DOI: https://doi.org/10.1016/j.matlet.2014.02.052

IF: 3

2014-01-01

Materials Letters

Abstract:Crack propagation in sputter-deposited freestanding nanocrystalline tungsten films with a thickness of 38nm was studied using an in situ transmission electron microscopy (TEM) tensile technique. Distinct from coarse-grained tungsten, a totally intergranular fracture mode and toughening mechanisms were identified in the nanocrystalline tungsten. The transition of the fracture mode indicates that the plasticity is improved, and the improvement may be attributed to the effect of nano-size grains and the freestanding surface, which facilitate a high percentage of grain boundaries (GB) and a weak binding force. A theoretical model of the energy release rate and the deflection angle of cracks was established to quantitatively characterize the preferred deflection angle. The model predictions are in good agreement with the experimental findings.
Effect of Grain Size on Deformation and Fracture of Inconel718: an In-Situ SEM-EBSD-DIC Investigation

Wenjie Gao,Junxia Lu,Jianli Zhou,Ling'en Liu,Jin Wang,Yuefei Zhang,Ze Zhang

DOI: https://doi.org/10.1016/j.msea.2022.144361

IF: 6.044

2022-01-01

Materials Science and Engineering A

Abstract:The effects of grain size on tensile behavior of Inconel718 superalloy have been characterized by an in-situ tensile stage inside a scanning electron microscopy (SEM) combined with electron backscatter diffraction (EBSD) and digital image correlation (DIC) at room temperature. The microstructure evolution and mechanical properties of specimens under different heat treatments were performed and compared. The in-situ tensile test showed that the yield strength, ultimate tensile strength and reduction of cross section decrease with the increasing grain size. An in-situ EBSD study showed that with increasing stress the local plastic deformation become more inhomogeneous. An analysis combined in-situ SEM morphology evolution, DIC strain distribution and EBSD results indicated that the grains deformed coordinately. Geometrically necessary dislocation (GND) density depends on the grain size and the orientation of individual grains. The coordinated deformation ability decreased with increasing grain size. The fracture morphology showed that with the increase of grain size, the fracture mechanism transformed from the ductile transgranular fracture to the brittle intergranular-transgranular mixed fracture.
Dynamic Atomic Mechanisms of Plasticity of Ni Nanowires and Nano Crystalline Ultra-Thin Films

Xiaodong Han,Lihua Wang,Pan Liu,Yonghai Yue,Mingjie Yang,Jialin Sun,Ze Zhang

DOI: https://doi.org/10.4028/www.scientific.net/msf.654-656.2293

2010-01-01

Materials Science Forum

Abstract:Using our recently developed in situ transmission electron microscopy techniques, we revealed that the FCC structured Ni nanowires with diameter of about 30 nm possess ultra-large strain plasticity. Dynamic complex dislocation activities mediated the large strain bent-plasticity and they were monitored at atomic scale in real time. The bent-induced strain gradient allows studying the strain effects on dislocation mediated plasticity. We also explored the deformation techniques to more general cases, the nano thin films. An example of tensile Pt ultra-thin film is presented.
In-situ high energy X-ray diffraction study of deformation behavior in Nb nanoparticle-martensitic NiTi composite wire

Xiangguang Kong,Ying Yang,Yang Ren,Lishan Cui,Shijie Hao

DOI: https://doi.org/10.1016/j.compositesb.2023.110856

2023-08-01

Abstract:This study investigated the deformation behavior in Nb nanoparticle-martensitic NiTi composite wire during tensile loading by means of in-situ high-energy X-ray diffraction. Compared to Nb nanowires, the dispersedly distributed Nb nanoparticles have little effect on the transformation and deformation behaviors of NiTi matrix, causing the absence of R phase transformation and the occurrence of deformation twinning in NiTi matrix. Meanwhile, the occurrence of deformation twinning in NiTi matrix can reduce the shape strain to be coordinated by the unfavorable orientated martensite variants, and thus decreases the internal stress among NiTi martensite variants generated during martensite reorientation process. In addition, TEM result proved that Nb nanoparticles can achieve exceptionally large elastic strain in B19′-NiTi matrix (∼4%), just as Nb nanowires. However, this large elastic strain (stress) will be released with the occurrence of NiTi deformation twinning.

engineering, multidisciplinary,materials science, composites
B11-O-10In Situ Atomic Scale Mechanical Microscopy

Xiaodong Han,Ze Zhang

DOI: https://doi.org/10.1093/jmicro/dfv080

2015-01-01

Microscopy

Abstract:We developed in situ atomic scale mechanical microscopy (ASM) for investigation of the deformation dynamics of materials with simultaneous atomic scale imaging. The In situ TEM mechanical testing techniques are generally applicable to regular TEM samples by tensile experiment with simultaneous double tilt, and thus the ability of obtaining atomic scale imaging about the deformation dynamics of the deformed materials. We show several examples of the atomic scale deformation dynamics of Ni, Pt, Au and Cu as well as Cu-Zr metallic glass. It was revealed that these materials show unusual large strain elasticity, size-dependent elasto-plastic transitions and the unusual plasticity behaviors at nano-scale. For example, the cross-over plasticity mechanisms from partial dislocation to full dislocation and twins were discovered in deformation of nano single crystalline Cu samples. A long standing puzzle and uncertainties of grain rotation in ultra-small nano-sized polycrystalline materials (grain size less than 8nm) was demonstrated through this in situ: ASM. It was uncovered that the dislocation climb takes care of the grain rotation behaviors in small grain systems. These results shed lights in understanding the interesting mechanical behaviors and the related dislocation activities of the metallic materials at small scale and useful for designing new materials with strength and ductility as well as those applications in micro- and nano- electronics and mechanics.
Atomic-Scale-Deformation-Dynamics (asds) of Nanowires and Nanofilms

Ze Zhang,Yuefei Zhang,Kun Zheng,Yonghai Yue,Lihua Wang,Pan Liu,Xiaodong Han

DOI: https://doi.org/10.4028/www.scientific.net/msf.654-656.1190

2010-01-01

Abstract:Nanowires and nanofilms are fundamental building blocks of micro and nano-electronics for both of bottom-up and top-down technologies. Monitoring and recording the mechanical property dynamics at atomic scale are important to understand the atomic mechanism of new and surprising nano-phenomena and design new applications. Through years' endeavors, we developed tensile and/or bending in-situ atomic-lattice resolution electron microscopy methods and equipments for nanowires and successfully conducted atomic-lattice resolution mechanical tests on individual nano-objects. With this, we observed the brittle materials SiC and Si nanowires (NWs) become highly ductile at room temperature. The crystalline structural evolution processes corresponding to the occurrence of unusual large strain plasticity includes the dislocation initiation, dislocation accumulation and amorphorization as well as the necking of the one dimensional nanowires were fully recorded at atomic scale and in real time. We also expand the experimental methods and equipments to two-dimensional nanofilms. An example of tensile experiment on nano-crystalline Au films is presented. The deformation mechanisms of nano-crystalline gold films were observed at the atomic scale and real-time. At the mean time, an atomic scale the crack blunting behavior was captured and the plastic deformation mechanism of the single nano-crystalline was revealed.
Tensile deformation and fracture mechanisms of Cu/Nb nanolaminates studied by in situ TEM mechanical tests

Z. Liu,M.A. Monclús,L.W. Yang,M. Castillo-Rodríguez,J.M. Molina-Aldareguía,J. LLorca

DOI: https://doi.org/10.1016/j.eml.2018.10.007

IF: 4.728

2018-11-01

Extreme Mechanics Letters

Abstract:The mechanisms of deformation and failure of Cu/Nb nanolaminates manufactured by accumulated roll bonding were analysed using in-situ TEM mechanical tests. Dog-bone small-scale tensile specimens were prepared using a FIB-based technique with the layers parallel and perpendicular to the loading axis. Load, deformation and TEM micrographs were recorded during the in-situ TEM mechanical tests. The specimens deformed parallel to the layers presented very high strain hardening and ductility while those deformed in the perpendicular orientation were more brittle. These results were rationalized in terms of the deformation and fracture mechanisms observed during the tests.

mechanics,materials science, multidisciplinary
In situ TEM studies of the large plastic deformation of nanocrystalline gold nanowire

Yue MENG,Lihua WANG,Ze ZHANG,Xiaodong HAN

DOI: https://doi.org/10.3969/j.issn.1000-6281.2014.04.003

2014-01-01

Abstract:In this paper, the deformation behaviors of nanocrystalline gold nanowire were in-situ observed with homemade TEM double tilt tensile device. The nanocrystalline nanowires exhibit approximate 48% of homogeneous elongation ability. The in-situ TEM observation indicates that the ultra-large plastic deformation is realized through the coordination of grain boundary sliding and grain boundary migration. During the deformation process, the grain boundary sliding provides the large plastic deformation ability, which is at the mean time accommodates by the grain boundary migration.
Atomistic Processes of high-temperature plastic deformation of nanoscale body-centered cubic tungsten

Sixue Zheng,Zhengwu Fang,Scott X. Mao

2023-11-08

Abstract:Much scientific and practical interest is currently focused on the atomic-scale mechanical behaviors of metallic nanocrystals with different crystal structures at room temperature, while the high-temperature plastic deformation in tungsten nanocrystals remains not well understood, due to the technical difficulty in elevating the experimental temperature during in situ mechanical tests in an extremely small chamber of transmission electron microscopes. In this study, a in situ high-temperature nanomechanical testing method is developed based on electrical-current-induced Joule heating in the metallic nanocrystal. By this method, it is found that three distinct deformation modes, that is deformation twinning, body-centered-cubic-face-centered-cubic-body-centered-cubic phase transformation and perfect dislocation slip, are sequentially activated in the tungsten nanocrystal during high-temperature tensile test. Such ductile behavior is related to not only the experimental temperature and but also the loading orientation. These findings shed light on the atomic-scale plastic deformation in body-centered cubic metals at elevated temperature.

Materials Science

In-Situ TEM Studies of the Deformation Mechanism of Nanocrystaline Ni

Revealing the Mechanical Bending Mechanisms of Single-Crystalline Rutile TiO2 Nanowires Near Room Temperature: Implications for Nanostructured Semiconductors

In Situ TEM Study on the Nanomechanical Behaviors of Metallic Nanowires

In Situ Nanomechanical Testing of Twinned Metals in a Transmission Electron Microscope

A Molecular Dynamics Study on Mechanical Performance and Deformation Mechanisms in Nanotwinned NiCo-based Alloys with Nano-Precipitates under High Temperatures

In Situ Atomistic Observation of the Deformation Mechanism of Au Nanowires with Twin–twin Intersection

In-Situ HR-TEM Characterizations on Individual Carbon Nanotubes During Its Manipulation, Deformation and Growth

In-situ Fabrication, Manipulation and Property Measurements of Single Nanotubes and Nanowires with Near Atomic Resolution

Research on Deforming Mechanism of Nanocrystalline Cu Thin Film under Contact Deformation

In Situ Tem Nanomechanics

Recent Electron Microscopy Results on Micro- and Nanostructured Ni-Ti-(X) Shape Memory Alloys

In-situ observation of crack propagation through the nucleation of nanoscale voids in ultra-thin, freestanding Ag films

In situ observation of intergranular fracture propagation in nanocrystalline freestanding ultrathin tungsten film

Effect of Grain Size on Deformation and Fracture of Inconel718: an In-Situ SEM-EBSD-DIC Investigation

Dynamic Atomic Mechanisms of Plasticity of Ni Nanowires and Nano Crystalline Ultra-Thin Films

In-situ high energy X-ray diffraction study of deformation behavior in Nb nanoparticle-martensitic NiTi composite wire

B11-O-10In Situ Atomic Scale Mechanical Microscopy

Atomic-Scale-Deformation-Dynamics (asds) of Nanowires and Nanofilms

Tensile deformation and fracture mechanisms of Cu/Nb nanolaminates studied by in situ TEM mechanical tests

In situ TEM studies of the large plastic deformation of nanocrystalline gold nanowire

Atomistic Processes of high-temperature plastic deformation of nanoscale body-centered cubic tungsten