Abstract:The designed service temperature of turbine blades is rising with the increasing thrust of aircraft engines. A film cooling system is one of the promising ways to improve the service temperature of turbine blades. However, such a complex film cooling system can reduce the thickness of the blade airfoil and lead to obvious local differences in microstructure; these differences are caused by solidification and mechanical resistance between the blade airfoil and alloys such as standard solid bars. In this study, a thin-walled tube manufactured by the casting process was used to simulate the microstructure of the hollow blade airfoil. The tube was thermally exposed at a temperature range of 900 similar to 1050 degrees C for 300 similar to 1000 h, and the corresponding stress rupture properties under 975 degrees C and 225 MPa (pressure) were examined. The microstructures were investigated using OM, SEM, TEM, and XRD, and the chemical compositions of the precipitates formed were measured through physicochemical phase analysis before and after the thermal exposure. Through this analysis, the relationship between microstructural degradation and stress rupture properties was revealed. The results indicated that dissolution and coarsening of gamma' precipitates, degeneration of MC carbides, and broadening of the gamma' film along the grain boundaries occurred in the K465 alloy tube during thermal exposure between 900 degrees C and 1050 degrees C . With increasing exposure temperatures and prolonged thermal exposure time, the degree of degradation of the gamma' precipitates, carbides, and grain boundaries gradually increased. This resulted in a gradual reduction in stress rupture lives. Unlike the phenomenon observed in our previous study in which a large amount of p phase precipitated in the solid bar following thermal exposure at 900 degrees C; in the present study, the p phase did not form in the tube. However, the degrees of microstructurel degradation in the tube and bar were similar after the thermal exposure at 1000 and 1050 degrees C. The stress rupture lives of the tube were significantly higher than those of the bar after the thermal exposure at 900 whereas their stress rupture lives were similar after the thermal exposure at 1000 and 1050 degrees C. The thin-wall effect caused by the cooling rate on the microstructure and the corresponding stress rupture property of K465 alloy was obvious at 900 degrees C , whereas it was negligible at 1000 and 1050 degrees C . These results provided guidance for the manufacturing and evaluation of microstructural degradation of turbine blades made of conventionally cast polycrystalline superalloys.

Influence of Cooling Structure on Strength of Superalloy Turbine Blade

Dependence of Microstructural Evolution on the Geometric Structure for Serviced DZ125 Turbine Blades

Microstructure Degradation of Service-Exposed Turbine Blades Made of Directionally Solidified DZ125 Superalloy

Influence of Dimension Variation on Strength and Fatigue Life of Single Crystal Cooled Blade

Multidisciplinary Design Optimization of the Composite Cooling Structure for Nickel-based Alloy Turbine Blade

Crystal orientation effect and multi-fidelity optimization of a solid single crystal superalloy turbine blade

Thermal-Fluid-Solid Coupling Analysis on the Temperature and Thermal Stress Field of a Nickel-Base Superalloy Turbine Blade

The influence of crystal orientations on fatigue life of single crystal cooled turbine blade

Fatigue Failure Behavior and Strength Prediction of Nickel-Based Superalloy for Turbine Blade at Elevated Temperature

Investigation on Mechanical Properties of MAR-M247 Superalloy for Turbine Blades by Experiment and Simulation

Numerical Simulation and Prediction of Solidification Structure and Mechanical Property of A Superalloy Turbine Blade

Tensile behavior of single-crystal superalloy with different structured cooling holes

Tensile property of a modeling specimen of DD6 single crystal cooling turbine blade

Investigation on crystallographic behaviors of nickel-base single crystal alloy cooling holes with different spanwise injection angles

Cooling Rate Driven Thin-Wall Effects on the Microstructures and Stress Rupture Properties of K465 Superalloy

Strength Analysis and Structure Optimization About Turbine Blade

Research Progress on Thin-Wall Effect of Nickel-Based Single Crystal Superalloy Turbine Blades

The Influence of the Cooling Bores on Crystal Orientation and Lattice Parameter in Single-Crystalline Cored Turbine Blades

Effects of Solidification Parameters on Microstructure and Mechanical Property of A Ni-Based Superalloy K35 Blade

Numerical Analysis of Conjugated Heat Transfer and Thermal Stress Distributions in a High-Temperature Ni-Based Superalloy Turbine Rotor Blade

Structural Strength Change by Single Crystallization of Turbine Blades and Vanes