Abstract:Ni–SiC nanocomposite coatings were prepared on a brass substrate by electrocodeposition. The electrodeposition was carried out by adding the SiC nanoparticles to a nickel-containing bath. Nickel deposition processes were analyzed by cathodic polarization curves, and the plating parameters were determined preliminarily by analyzing the effects of different technological parameters on the deposition process. Then, electrocodeposition processes were carried out with different concentrations of SiC nanoparticles in the bath. The effects of current density, stirring rate, and SiC nanoparticle’s concentration in the plating bath on the hardness of coatings were investigated by microhardness tests. Besides the microhardness tests, wearing tests and corrosion tests were also applied to the coatings with the highest hardness and coatings of pure nickel. The structures and surface morphologies of the coatings were examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM) methods. The experimental results show that the microhardness of the codeposited coating increases with increasing current density and attains a maximum at the SiC concentration of 6 g/L. The decrease in the microhardness at higher SiC concentrations may be due to agglomeration of nanosized particles in the plating bath. Increasing the stirring speed did not give a better quality deposition as coatings produced at low stirring rates always had higher microhardness values than did those at high stirring rates. Furthermore, the Ni–SiC nanocomposite coatings have lower friction coefficient and better corrosion resistance than those of pure nickel coatings.

Influence of Surfactant on the Properties of Electroplated Ni-SiC Composite Coating

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Electrochemical Properties and XPS Analysis of Ni-B/SiC Nanocomposite Coatings

Effects of Surfactants SDS and CTAB on Ni-SiC Deposition

Preparation, Mechanical Properties and Wear Resistance of Ni–W/SiC Nanocomposite Coatings

Influence of Electrodeposition Process Parameters and Si3N4 Nanoparticle Concentration on Microhardness and Wettability of Ni-Co-Si3N4 Nanocomposite Coatings

Effects of Surfactants on Electroless Ni-P Plating on Al2O3 Ceramic and Properties of Coatings

A Study of Electroless Ni Plating on SiCp/Al Composite Materials

Effect of SiC Contents on Wear Resistance Performance of Electro-Codeposited Ni-SiC Composite Coatings

Effect of SiC Nanoparticles on the Structure and Properties of Ni+W-SiC Nanocoatings

Effect of Pretreatment Modes of Silicon Carbide Nanoparticulates on the Properties of Electroplated Ni-SiC Nanocomposite Coatings

Enhanced mechanical and wear properties of Ni-W-SiC composite coatings by synergistic influence of micro-nano SiC mixture

A Study on the Electrocodeposition Processes and Properties of Ni–SiC Nanocomposite Coatings

Effect of Α-Al2o3 Coatings on the Interface of Ni/SiC Composites Prepared by Electrodeposition

Study of fabrication and wear properties of Ni–SiC composite coatings on A356 aluminum alloy

Corrosion Behavior of Ni-P-Nano-Al2o3 Composite Coating in the Presence of Anionic and Cationic Surfactants

Comparative study on the wear resistance and corrosion resistance of NiW and NiCoW composite coatings with micro- and nano-SiC particles

Investigation on Microstructure and Properties of the Electrodeposited Ni-SiC Composite Coating

Electroless deposition of nickel on the surface of silicon carbide/aluminum composites in alkaline bath

Enhanced Mechanical and Tribological Capabilities of a Silicon Aluminum Alloy with an Electroplated Ni–Co–P/Si3N4 Composite Coating

Influence of a Zwitterionic Surfactant on the Surface Properties of Electroless Ni–P Coating on Mild Steel