Abstract:The study employed high-temperature X-ray diffraction, quantitative phase analysis, and tensile mechanical property measurements to investigate the relationship between coefficient of thermal expansion (CTE) and phase composition, along with the average yield strengths and Young's moduli of Al–Cu–Li alloys in three different sheet orientations: 1441, V-1461, V-1469, V-1480, and V-1481. The copper content within the solid solution and the mass fractions of the T 1 (Al 2 CuLi) and δ′(Al 3 Li) phases were determined using an innovative technique based on measuring the lattice distance of the α solid solution, Vegard's law, and balance equations for the elemental and phase compositions of the alloys. It was observed that as the lithium-to-copper ratio in the alloys increased from 0.32 to 1.12, the proportion of the δ′(Al 3 Li) phase increases from 6.3–8.4 wt.% in V-1481, V-1480 and V-1469 alloys to 16.0–17.3 wt.% in 1441 and V-1461 alloys, accompanied by a decrease in the T 1 (Al 2 CuLi) phase from 5 to 1 wt.%. This led to an increase in the Young's modulus from 75 to 77 GPa due to higher overall proportion of intermetallic compounds and a reduction in yield strength from 509 to 367 MPa due to the decrease in the T 1 phase. This decrease in yield strength resulted from the fact that the hardening effect of the T 1 phase was 3–4 times greater than that of the δ′ phase, and this couldn't be offset by an increase in the total intermetallic compound proportion. The observed increase in Young's modulus indicated that the elastic properties of the intermetallic phases were similar, and the rise in the total fraction of intermetallic compounds compensated for the decrease in the T 1 phase. Furthermore, it was demonstrated that СTE, as measured based on the thermal expansion of the solid solution, also depended on the characteristics of the intermetallic phases present in the alloy. This expanded the potential interpretations of СTE measurement results.

Ultrasonic Velocity Measurement of Elastic Constants of Al-CuAl2 Eutectic Composite

Determination of the Elastic Constants of Metal-Matrix Composites by A Laser Ultrasound Technique

Elastic Constant Measurement from Vibrational Mode Frequencies in Resonant Ultrasound Spectroscopy

Elastic Property of Cu_(58.1)Zr_(35.9)Al_6 BMG by Velocity Method

On Measuring the Dynamic Elastic Modulus for Metallic Materials Using Stress Wave Loading Techniques

Anisotropic in elasticity, sound velocity and minimum thermal conductivity of Al-Cu intermetallic compounds

Measurement of the Anisotropic Dynamic Elastic Constants of Additive Manufactured and Wrought Ti6Al4V Alloys

On the Measurement of the Elastic Constants of Small-size Samples by Ultrasonic Method

Measurement of Elastic Constants Using HalbachArray Enhanced EMAT

First-Principles Investigation of Elasticity, Thermal and Electronic Properties of Intermetallics Formed at the Interface of Al-Cu Composites

Measurement of Elastic Constant Matrix of Carbon Fiber Composites With an Ultrasonic 2D-Array Transducer

Determining the Elastic Constants of Isotropic Materials by Measuring the Phase Velocities of the A0 and S0 Modes of Lamb Waves

In-plane Elastic Anisotropic Constants (ieacs) Measurement of Rolling Aluminum Plate at Different Depth Using Ultrasonic LCR Wave

The Elastic Constants Measurement of Metal Alloy by Using Ultrasonic Nondestructive Method at Different Temperature

Microstructure characterization and hardness of Al-Cu-Mn eutectic alloy

The Elastic Constants of Moulded Polymeric Composites

Ultrasonic Evaluation of Acoustoelastic Parameters in Aluminum

Determination of the Elastic Constants of Ceramic Matrix Composites by Ultrasonic Wave Propagation Characteristics

Investigation into the Impact of Phase Composition on the Thermal Expansion and Mechanical Properties of Al–Cu–Li Alloys

Nondestructive Measurements of Elastic Constants of Thin Rods Based on Guided Waves

Measurement of fiber reinforced composite engineering constants with laser ultrasonic