Abstract:Gas distributor is a key component in fluidized beds. Various gas distributors for practical application have been successfully developed and studied in depth. Fluidization of coarse particles is still a challenge for good gas-solid contacting. In this study, a slotted gas distributor with simple structure was proposed for the fluidized bed processing coarse particles. The fluidization characteristics of the Geldart D type large particles (2-2.8 mm walnut shell) were investigated experimentally in a 285 mm × 190 mm × 700mm fluidized bed with the slotted gas distributor whose opening rate was 5.6%. The experimental results were compared with the ones obtained from the traditional perforated distributor. It was found that the bed expansion ratio increased by about 5% and the minimum fluidization velocity reduced by about 8% when using the slotted gas distributor, indicating that the slotted gas distributor had better fluidization characteristics for the large-sized particles. To explain the better fluidization performance of the slotted gas distributor, a computational fluid dynamics (CFD) model was developed based on the Eulerian-Eulerian model, the particle kinetic theory, the standardk-ε turbulence model and the SIMPLE algorithm. The CFD model was used to simulate the behaviors of the gas particle flow in the fluidized bed of walnut shell particles with slotted gas distributor or traditional perforated distributor, and the results of experiment and simulation were agreed well. The simulations were conducted under such operation conditions: The physical two-dimensional model of the rectangular fluidized bed was 285 mm × 700 mm with slotted gas distributor or traditional perforated distributor in which the opening rate was 5.6%. Particles packed in the fluidized bed had the volume fraction of 0.6 and the height of the bed was 200 mm. The superficial gas velocity of inlet was selected as operation parameter, which ranged from 0.615 to 1.128 m/s. The simulation results were compared on the bed pressure fluctuations due to bubble formation, the coalescence and eruption, the maximum bed expansion radio, the transient particle volume fraction distribution, the gas/particle velocity vector distribution and so on between the fluidized beds of these two distributors. It was observed that small bubbles first formed close to the gas distributor, coalesced when rising up, and finally erupted near the bed surface, which resulted in periodic fluctuations of bed pressure with different amplitudes and frequencies. Compared with the traditional perforated distributor, the frequency and amplitude of the bed pressure drop fluctuation caused by the slotted gas distributor were bigger and the bed expansion ratio was higher. The change of the particle concentration in the bed was scattered in the fluidized bed with slotted gas distributor, which was beneficial to the fluidization of particles near the bed wall. Also, the dead zone and recirculation area formed near the wall area were reduced. The V-shaped structure of the slotted gas distributor generated strong upward flow jets. The strong jets could deeply reach the material particle bed and easily bring the formation of bigger bubbles. The bigger bubbles caused more intensive disturbance inside the material bed, and thereby the bed pressure drop fluctuation and the bed expansion ratio were improved. Four small circulations were observed to form within the fluidized bed with slotted gas distributor, which was beneficial to the better mixing of gas and particle. Therefore, coarse particles of walnut shell can be well fluidized with the slotted gas distributor. The study provides a reference for the design and selection of fluidized bed distributor in the process of coarse particle processing in fluidized bed.

Effect of Gas Distributor on Fluidization Characteristics and Reduction Reaction of Mixed Phosphate Ore Particles

Effect of gas distributor on gas–liquid dispersion and mass transfer characteristics in stirred tank

Study on thermal reduction of phosphate ore by carbon in the fluidized bed reactor

Effect of Aluminium Sulfate on Carbothermal Reduction of Phosphorite in a Fluidized Bed

Phosphorus reduction behavior of high-phosphate iron ore during hydrogen-rich sintering

Reaction kinetics of phosphate ore with carbon by smelting reduction technology

Process Parameters and Kinetics of Smelting Reduction Technology for Low-Grade Phosphate Ore Reduction

Fluidization characteristics of ore particles for downstream hydrogen mineral phase transformation equipment

Gasification Behavior of Phosphorus during Hydrogen-rich Sintering of High-phosphorus Iron Ore

Fluidization Effect of Walnut Shell Particles in Fluidized Bed with Slotted Gas Distributor

Experimental Study on Fluidization Characteristics of Phosphate Ore Particles

Influence study on dephosphorization of carbon-containing high-phosphorus iron ore by microwave field

A Numerical Study on the Process of the H2 Shaft Furnace Equipped with a Center Gas Distributor

Optimization of medium–low-grade phosphorus rock carbothermal reduction process by response surface methodology

Hydrodynamic Behaviors of a Spouted Fluidized Bed with a Conical Distributor and Auxiliary Inlets for the Production of Polysilicon with Wide-Size-distribution Particles

Effect of distributor structure on the particle distribution in a vertical two-pass circulating fluidized bed evaporator with a baffle

Reaction kinetics of smelting reduction for phosphorous production with magnesium phosphate slag

Recombination of Hydrogen and Oxygen in Fluidized Bed Reactor with Different Gas Distributors

Study on Fluidization Characteristics of Phosphate Ore Particles with Application of Vibration Field and Addition of SiO2 Particles

The Leaching and Kinetics of Magnesium in Phosphate Ore Slurry During FGD Process

Effect Of Different Additives On Reaction Characteristics Of Fluorapatite During Coal-Based Reduction Of Iron Ore