Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Studies on cure kinetics of epoxy friction material for ultrasonic motor

Cure Kinetics of an Epoxy Resin Containing Naphthyl/dicyclopentadiene Moieties and Bis‐phenoxy (3‐hydroxy) Phosphine Oxide System and Properties of Its Cured Polymer

The Curing Behavior and Properties of Diglycidyl Ether of 4,4′-Bis(4-hydroxybenzoyloxy)-3,3′,5,5′-tetramethylbiphenyl and Its Composites with Multi-Wall Carbon Nanotubes

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Studies on Cure Kinetics of Diglycidyl Ether of 4,4′-Bisphenol/4,4′-diaminobiphenyl Using the Advanced Isoconversional Method

Experimental Study of Friction Material adhere to the Stator of the Traveling Wave Type Rotary Ultrasonic Motor

Tribological performance of filled PTFE-based friction material for ultrasonic motor under different temperature and vacuum degrees

Experimental Investigation on Friction Characteristics of Ultrasonic Motor

CURE KINETICS OF A TGDDM EPOXY/DDS System MODIFIED WITH POLYSULFONE NANOFIBER

Study on the Curing Behavior of Polythiol/phenolic/epoxy Resin and the Mechanical and Thermal Properties of the Composites

Research on PTFE-based Friction Materials of Ultrasonic Motor

Effect Of Hardness Of Frictional Materials On Properties Of Ultrasonic Motors

Crosslink UHMW-PE matrix composite for to traveling wave rotary ultrasonic motor

Cure Kinetics of Carbon Nanotube/tetrafunctional Epoxy Nanocomposites by Isothermal Differential Scanning Calorimetry

The curing kinetics and mechanical properties of epoxy resin composites reinforced by PEEK microparticles

Cure Kinetic Study of Carbon Nanofibers/Epoxy Composites by Isothermal Dsc

Cure Kinetics of Epoxy Resin Used for Advanced Composites

STUDY OF CURING BEHAVIORS OF CARBON NANOTUBES/EPOXY COMPOSITES

Thermal Characterization of Carbon‐nanofiber‐reinforced Tetraglycidyl‐4,4′‐diaminodiphenylmethane/4,4′‐diaminodiphenylsulfone Epoxy Composites

Cure Kinetics of Epoxy-Based Nanocomposites Analyzed by Avrami Theory of Phase Change

Testing and Analysis of Frictional Performance of Carbon Fiber/Metal Composite Materials