Abstract:Plasma electrolytic oxidation (PEO) of Mg‐based AZ91D alloys was investigated using 50 Hz AC anodizing technique in an alkaline borate solution, which contained a new kind of organic additive and without F, P, and Cr. The anodizing technological parameters have been optimized and a kind of ivory‐white smooth anodic film with high corrosion resistance was obtained. It was found that the formation of the anodic films was always coupled with sparking and oxygen evolution, whose intensity changed with the additive and anodizing voltage. All EIS plots have two capacitive loops and one low frequency inductive component. Two capacitive arcs present the barrier and porous layer of the PEO film and the inductive component in the low frequency domain is a complex behavior due to the porous structure connected to the electrolyte. EIS plots and fitting results show that a self‐sealing process of the PEO firm with different additives takes place in the beginning of immersion time, then corrosion attack becomes a preponderant process to promote the degradation of the film. Tafel results show that PEO treatment decreases the corrosion current density by four, even five orders of magnitude, while additives content does not affect strongly the electrochemical corrosion behavior. Salt spray test shows that the PEO film formed with NaAlO2 and Na2SiO3 presents good corrosion resistance, over 600 h without any sealing treatment. The difference of corrosion resistance arose by additives examined by electrochemical techniques and salt spray test does not show strict corresponding relationship.

Optimization of the Bath Composition for Anodizing of Mag-nesium Alloys

Micro-arc Oxidation Behaviors of AZ91D Magnesium Alloy in Different Electrolytes

Study on structure and properties of microarc oxidation coating on magnesium alloy in phosphate-potassium hydroxide solution

Study on Structure and Properties of Microarc Oxidation Coating Formed on AM60B Magnesium Alloy

Anodization of AZ91 Magnesium Alloy in Alkaline Solution Containing Silicate and Corrosion Properties of Anodized Films

Study on the anodizing of AZ31 magnesium alloys in alkaline borate solutions

Corrosion Properties of AZ31 Magnesium Alloy and Protective Effects of Chemical Conversion Layers and Anodized Coatings

Effect of ZrSiO4 Concentration on the Microstructure and Corrosion Resistance of MAO Coatings Formed on AZ91 Magnesium Alloy

Influence of Anodic Oxidation on the Organizational Structure and Corrosion Resistance of Oxide Film on AZ31B Magnesium Alloy

Study on the Environmentally Friendly Anodizing of AZ91D Magnesium Alloy

Anodizing of AZ91D Magnesium Alloy Using Environmental Friendly Alkaline Borate-Biphthalate Electrolyte

Environmental friendly anodizing of AZ91D magnesium alloy in alkaline borate–benzoate electrolyte

EFFECT OF ELECTROLYTE CONSTITUENTS ON PROPERTIES OF ANODIC COATINGS OF MAGNESIUM ALLOYS

Optimization of the Corrosion Resistance of Electroless Ni–W–P Coatings on Magnesium Alloys by the Response Surface Methodology

The Effect of Phosphate on MAO of AZ91D Magnesium Using AC Power Source

Corrosion resistance enhanced by an atomic layer deposited Al2O3 /micro-arc oxidation coating on magnesium alloy AZ31

Plasma Electrolytic Oxidation of AZ91D Magnesium Alloy with Different Additives and Its Corrosion Behavior

Evaluation of the micro-arc oxidation treatment effect on the protective performance of a Mg-rich epoxy coating on AZ91D magnesium alloy

Optimization of the Experimental Parameters Affecting the Corrosion Behavior for Mg–Y–Zn–Mn Alloy via Response Surface Methodology

The Anodization of Zk60 Magnesium Alloy in Alkaline Solution Containing Silicate and the Corrosion Properties of the Anodized Films

Anodizing of Az91d Magnesium Alloy in Borate-Terephthalic Acid Electrolyte