Abstract:Tailoring the phase constitutions of the interfacial reaction layers under the assistance of ultrasonic vibration is a convenient method to fabricate high-strength Al/Cu brazing joints. In this study, 1060-Al and T2-Cu dissimilar metals were ultrasonically brazed with Zn-3Al (wt. %) filler metals. Effects of ultrasonic brazing time on the microstructure and mechanical properties of joints were investigated. Results showed that the CuZn5 intermetallic compound (IMC) layer and Cu-based diffusion layer were created on the Cu substrate surface in the joint ultrasonically brazed at 400 ℃ for 2 s. However, the CuZn5 IMC layer was gradually transformed into a thin Al4.2Cu3.2Zn0.7 IMC layer by increasing the ultrasonic vibration time to 15 s. A well-matched coherent interface was formed between the Al4.2Cu3.2Zn0.7 ternary phase and the Cu-based diffusion layer. The phase transition of the Cu-side interfacial layer correlated closely with the acoustic cavitations induced super-saturation regions near the Cu substrate surface. The measured tensile strength of the Al/Zn-3Al/Cu joint ultrasonically brazed for 15 s was 89.3 MPa, which was approximately 2.5 times higher than that brazed for 2 s, and the tensile failure mainly occurred at the interface between the Al4.2Cu3.2Zn0.7 layer and the Cu-based diffusion layer.

Ultrasonic Brazing of Aluminium Matrix Composites Assisted by Operation of Melting and Squeezing

Capillary Filling Process During Ultrasonically Brazing of Aluminium Matrix Composites

High-performance joining technology for aluminium matrix composites using ultrasonic-assisted brazing

Ultrasonic brazing of high fraction volume of SiC particulate reinforced aluminium matrix composites

Ultrasonically Aided Brazing of SiCp/A356 Composites

Ultrasonic assisted fabrication of particle reinforced bonds joining aluminum metal matrix composites

Strengthening Mechanism of Ceramic Particle Reinforced Bonds by Ultrasonic Brazing of AlMMCs

Microstructure and Strength of Ultrasonic-Assisted Brazed Joints of Si3N4/6061Al Composites

Ultrasonic brazing of SiC particulate reinforced aluminum matrix composites with high fraction volume

Microstructure and Mechanical Properties of Ultrasonically Assisted Brazing of Dissimilar Cu–Al Alloys

Ultrasonic Dissolution of Brazing of 55% SiCp/A356 Composites

Ultrasonic-Assisted Semi-Solid Forming Method and Microstructure Evolution of Aluminum/Copper Brazed Joints

Interfacial Microstructure and Mechanical Properties of Ultrasonic-Assisted Brazing Joints Between Ti–6Al–4V and ZrO2

Microstructure and Mechanical Properties of Ti–6Al–4V/Al1060 Joints by Ultrasonic-Assisted Brazing in Air

Si Particulate-Reinforced ZnAl Based Composites Joints of Hypereutectic Al50Si Alloys by Ultrasonic-Assisted Soldering

Interfacial Structure and Formation Mechanism in Ultrasonically Aided Liquid Bonding of Al18B4O33/Al Composites in Air

Vibration assisted brazing of SiCp/A356 composites: Microstructure and mechanical behaviour

Ultrasound-assisted Brazing of Cu/Al Dissimilar Metals Using a Zn–3Al Filler Metal

Effect of Ultrasonic Transmission Rate on Microstructure and Properties of the Ultrasonic-Assisted Brazing of Cu to Alumina.

Formation of Amorphous Interfacial Layer Between Zn-based Alloy and SiC Particles under Ultrasonic-Assisted Brazing

Acoustic cavitation-induced microstructure evolution in ultrasonically brazed Al/Cu joints using Zn-Al alloy fillers