Abstract:Further development of capillary electrochromatography (CEC) is to some extent restricted by column technology. Packed capillary columns are most commonly used in CEC because of higher sample capacity and higher sensitivity than open tubular columns, and better reproducibility and uniformity than monolithic columns. Fritting is the core component for the fabrication of packed capillary columns. Therefore various fritting technologies attract continuous attention from analytical community. A convenient fritting method was developed in this study. In contrast to the reported single-particle fritting, this method applies a multi-particle fritting technology to hold stationary phase in capillary columns. Several large porous particles smaller than the column internal diameter were tapped in and immobilized in inlet and outlet of the packing material bed due to direct and indirect keystone effect. Except the smallest permeability by the sintered frit and the lowest breaking pressure by the single-particle frit, EOF mobility and peak dispersion of the multi-particle frit were at the same levels with the formers. In addition, all the three frits avoided bubble formation. It demonstrated that the multi-particle frits met the general requirements of permeability, mechanical resistance and efficiency for packing capillary microcolumns as well as the sintered frits and the single-particle frits. Thus, peak efficiency around 4.3 μm plate height (approximately 232,560 plates per meter) was obtained by multi-particle fritted capillary columns with electrokinetic packing, compared to 6.5 μm plate height by single-particle fritted columns with slurry pressure packing. In particular, the multi-particle fritting was simpler, faster, and more reproducible than the sintered fritting, and the multi-particle fritting was suitable to pack capillary columns of various capillary bore sizes owing to rich commercial resources of fritting particles of various diameters. Multi-particle fritted columns offered satisfactory run-to-run and column-to-column reproducibilities for retention factor, plate height and peak area (precisions of 4.1-9.3% for 10 replicated columns, and precisions of 0.9-3.1% for 30 replicated trials). They also had consistent CEC performance (differences of 1.1-3.9% between the first and 31 st day) during a lifetime more than one month. Application examples in packing capillary columns of 75 and 100 μm i.d. and CEC analysis of sixteen polycyclic aromatic hydrocarbons prove the diversity and reliability of the multi-particle fritting in column technology.

Application of an In-Situ Thermo-polymerized Porous Polymer: Creation of an On-column Frit for a Packed Capillary HPLC Column

Preparation of On-column Frit for Packed Capillary HPLC Column by In-situ Thermo-polymerized Porous Polymer

The Study of the Submicroparticle Packed Column

Multi-particle Frits for Packed Capillary Columns in Electrochromatographic Use

Single step on-column frit making for capillary high-performance liquid chromatography using sol-gel technology.

Preparation and Performance of Inorganic Silica Gel-organic Polymer Mixture Based C_(16) Capillary Monolithic Column

Design and fabrication of fluorous monoliths with tunable surface property for capillary liquid chromatography

Preparation and characterization of inorganic silica-organic polymer mixture based C16 capillary monolithic column

A novel one‐pot strategy of preparation of N ‐phenylacrylamide‐styrene co‐polymer open tubular capillary column for peptides separation

Preparation and evaluation of ultra-long open-tubular capillary columns modified with zeolitic imidazolate framework-8 incorporated polymeric porous layer for liquid chromatography

Fast construction of polymer monolithic columns inside fluorinated ethylene propylene (FEP) tubes for separation of proteins by reversed-phase liquid chromatography

Preparation and Application of Chiral Monolithic Column for Capillary Liquid Chromatography

Use of Gel-Casting to Prepare HPLC Monolithic Silica Columns with Uniform Mesopores and Tunable Macrochannels

Preparation of perfusive chromatographic materials via shear-induced reactive gelation

Preparation of a poly(3'-azido-3'-deoxythymidine-co-propargyl methacrylate-co-pentaerythritol triacrylate) monolithic column by in situ polymerization and a click reaction for capillary liquid chromatography of small molecules and proteins

Rapid Separation of Proteins by Capillary HPLC on a Short Polymethacrylate‐based Strong Cation‐exchange Monolithic Column

Controlling Pore Size and Wettability of A Unique Microheterogeneous Copolymer Film with Porous Structure

Surface-initiated Molecularly Imprinted Polymeric Column: in Situ Synthesis and Application for Semi-Preparative Separation by High Performance Liquid Chromatography.

Preparation and Evaluation of Zwitterionic Polymer Coated Capillary Columns for Analysis of Proteins by Capillary Electrophoresis

Monolithic column based on a poly(glycidyl methacrylate-co-4-vinylphenylboronic acid-co-ethylene dimethacrylate) copolymer for capillary liquid chromatography of small molecules and proteins

A practical interface designed for on-line polymer monolith microextraction: synthesis and application of poly(4-vinylpyridine-co-ethylene glycol dimethacrylate) monolith.